UNITED USF-669 User manual

INSTRUCTION MANUAL
16" STAND FAN 3 IN 1
Model: USF-669
READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire or electrical shock, do not use this
fan with any external speed control device.
This appliance can be used by children aged from 8 years
and above if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they
understand the hazards involved.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons.
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. To prevent fire or shock hazard, DO NOT expose this appliance to rain
or moisture.
2. Dangerous high voltages are present inside this enclosure. To avoid
electric shock, DO NOT open the cabinet, refer servicing to qualified
personnel only.
3. This appliance is intended for household use only and not for
commercial, industrial or outdoor use. Other use not recommended
may cause fire, electric shock or injury.
4. Ensure the fan is not placed near drapes,curtains, or any objects that
may be drawn into the fan.
5. To protect against fire, electrical shock and injury to persons, do not
immerse the unit, plug or cord in water or spray it with liquids.
6. The apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
product.
7. No naked flames sources, such as candles, should be placed on the
product.
8. Ventilation should not be impeded by covering the ventilation
openings. Slots and opening are provided for ventilation to ensure
reliable operation of the product and to protect it from overheating.
9. Care required with the use of this apparatus in tropical climates. Do
not use the appliance to temperatures over 40 °C.

10. Place the fan on a stable level and dry surface when operating to
avoid overturning.
11. Only connect to a suitably AC 220-240V~50Hz mains socket.
12. Do not operate the fan in the presence of explosive and/ or flammable
fumes. Do not place the fan or any parts near an open flame, cooking
or other heating appliance.
13. Do not operate the fan with a damaged cord or plug, after a
malfunction or if it is dropped or damaged in any manner.
14. Do not operate the fan without the fan grilles properly in place.
15. Do not place the fan close to an open window. Rain splashing on the
fan could cause an electric shock hazard.
16. Do not let the power cord hang over the edge of a table or counter or
let it touch any hot surfaces.
17. Do not insert or allow foreign objects to enter the grille openings as
this may cause damage to the appliance.
18. Do not use the fan if grille becomes damaged or loose.
19. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety.
20. Children should be supervised to ensure that they do not play with the
appliance.
21. Switch the fan OFF and unplug it from the outlet when it is not in use,
when moving fan from one location to another and before cleaning.
22. To disconnect, grip the plug and pull it from the wall outlet. Never pull
by the cord.
23.Do not attempt to repair, disassemble or modify the appliance. There
are no user-serviceable parts inside. Refer all servicing to qualified
service personnel.

ASSEMBLY INSTRUCTIONS:
Stand fan
1. Unscrew the pole clamp (14) from the lower base pole (15) by turning
counter-clockwise and set aside. Pull out the adjustable pole (13) all the
way to the top. (You may have to push it up from the bottom to get it up)
2. Set the base on a level dry surface and remove the screws from the
base (18), then install the lower base pole (15) and match the 4 holes over
the 4 screw holes on the base and replace the 4pcs of screws back onto
the base.
3. Place the base (18) on through the column with the tabs/slots pointed
downward.
4. Replace the pole clamp (14) and tighten by turning clockwise.
5. Place the fan motor into the top of the inner pipe, tighten the Set Screw.
6. Unscrew the rear guard central fixing nut (4) on the front of the motor by
turning counterclockwise.
7. Mount the rear guard (5) to the motor front cover by matching 3 holes on
the guard to the 3 round positioning knobs on the motor front cover. Push

in firmly until the 3 knobs protrude through the 3 holes.
8. Replace and tighten the rear guard central fixing nut (4) by turning nut
clockwise to hold the rear guard (5) in place.
9. Put the fan blade (3) onto the motor shaft by matching the shafts slots
with the blades slot, tighten the fan blade (3) with blade retaining nut (10)
by turning it counterclockwise.
10. Test fan by rotating the blade with your hands, make sure there isn’t
any contact with the nut. The fan blade should rotate freely, otherwise
repeat all steps again, beginning from step (4).
11. Mount front guard (1) onto the rear guard and use the guard nut and
screw (2) to fix them together.
Table fan
1.Insert the fan body on the base and tighten the screw behind the body.
2.Use the 4pcs screw to fix the base.
Wall fan
1.Use the 2pcs screw to fix the
base onto a wall.
2.Insert the fan body on the
base and tighten the screw
behind the body.

OPERATION:
1. Set the fan on a level dry surface.
2. Plug the power cord into a standard AC 220-240V wall outlet.
3. Rotate the speed key to set the desired speed 3=“HI” 2=“MED”
1=“LOW”.
4. Rotate back to the position 0=“OFF” key to turn the fan off.
5. To start or stop the fan head oscillation, press or pull the oscillating knob
on the top of
the motor housing.
6. To change the air flow angle, move the head forward or backwards.
MAINTENANCE
Always turn off the fan and remove the plug from the socket-outlet
before cleaning.
Clean the external surfaces of the fan with a soft damp (not
dripping wet) cloth.
WARNING:
Do not immerse the fan in water.
Do not use any cleaning chemicals such as detergents and
abrasives.
Do not allow the interior (special for the PCB) to get wet as
this could create a hazardous situation.
When the unit is not in use, make sure that it is unplugged from the
wall socket. To store the fan, you may pack it in the original carton
and store it in a cool and dry place until later use.
In case of malfunction or doubt, do not try to repair the fan yourself;
it may result in a fire hazard or electric shock.

NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high
quality materials and components which can be recycled
and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life,
should be disposed of separately from your household
waste. Please dispose of this equipment at your local
community waste collection/ recycling centre.
In the European Union there are separate collection systems for used
electrical and electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, Amiridis-Savvidis S.A. states that this product, complies with the
requirements of below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14/ 35 / EU
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU
The detailed declaration of conformity can be found at
www.united-electronics.gr
Exclusive importer in Greece:
Amiridis –Savvidis S.A.
87A, 17th Noemvriou str, P.C. 55534
Thessaloniki –Greece
T: [phone] | F: [phone]
www.amiridis-savvidis.gr
www.united-electronics.gr