Universal Tool UT8965 User manual

Description
The Universal Tool model UT8965 Positive Clutch is equipped with a 1/4" hexago-
nal quick change driver bit holder. Fully reversible with the flip of the lever makes
this a quick and easy tool to use. Ideal for sheet metal, wood and self-tapping
screws. Includes a 360° adjustable side handle to assist operator control, through
handle exhaust to reduce noise and a variable trigger to make starting screws
easier.
UT8965
POSITIVE CLUTCH SCREWDRIVER
PLEASE READ AND FOLLOW ALL WARNINGS
PL-0270
Universal Tool
A Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate
or service this Universal Tool product. Failure to comply with the
instructions could result in personal injury and/or property damage!
Retain these instructions for future reference.
Safety Instructions
The following general instructions are
furnished as general guidelines for use
of your pneumatic tool. They cannot
comprehensively cover all possible or
conceivable uses of the subject tool.
For additional information on the safe
use of air tools, we advise you to
obtain a copy of ANSI B186.1 Safety
Code for Portable Air Tools, available
from the following source:
American National Standards
Institute, Inc.
11 West 42nd Street
New York, NY 10036.
The use of the word “shall” in the
following instructions, indicates that
adherence to the particular require-
ment is necessary to conform to ANSI
B186.1.
Tool Application and Usage
Portable tools shall be used only for
the purposes intended in their design
and within the capacity for which they
were intended and rated. It shall be
the tool owner’s and/or employer’s
responsibility to instruct each operator
in the safe use of the tool. Tools shall
not be used without guards and safety
devices as furnished by the manufac-
turer. Where an air tool is modified or
altered, the modifier shall provide the
safeguards to enable it to be safely used
in the operations intended and to comply
with any applicable provisions as
contained in ANSI B186.1.
Tool Installation
Pressure regulators shall be used to limit
air pressure to the rated pressure where
the supply pressure exceeds the tool’s
rated pressure. Air hoses and lines shall
be relieved of compressed air before
being disconnected or disjointed, unless
there is automatic valve closing protec-
tion at the joint being separated. Syn-
thetic lubricants which can cause
deterioration of elastomer seals shall not
be used in air systems of air tools.
Tool Maintenance
It shall be the tool owner’s and/or
employer’s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools shall
be disconnected from their compressed
air supply before repairs are attempted.
Repairs shall be consistent with the
manufacturer’s recommended proce-
dures. Tool, hoses and fittings shall be
replaced if unsuitable for safe operation.
It shall be the tool owner’s and/or
employer’s responsibility to keep required
rating markings and warnings on the tool
in legible condition.
FPMC
Read Operating Instructions
Always become familiar with all the
instructions and warnings before
operating any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection
should meet or exceed the
standards as set forth in the United
States ANSI Z87.1, Occupational
and Educational Eye and Face
Protection. Look for the marking
Z87.1 on your eye protection to
insure that it is an approved style.
For further information, ANSI Z87.1,
Occupational and Educational Eye
and Face Protection, is available
from the American National
Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used
when the noise level exposure
equals or exceeds an 8 hour time-
weighted average sound level of 85
dBA. Process noise, reflective
surfaces, other tools being
operated nearby, all add to the
noise level present in your work
area. If you are unable to determine
your noise level exposure, we
recommend the use of hearing
protection.
Avoid Prolonged Exposure to
Vibration
Tools can vibrate during use.
Prolonged exposure to vibration or
very repetitive hand and arm
movements, can cause injury.
Stop using any tool if discomfort,
tingling feeling or pain occurs. You
should consult your physician
before resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at
an air pressure of 90 pounds per
square inch gauge pressure (90
PSIG) maximum, at the tool. Use of
higher air pressure can, and may
cause injury. Also, the use of
higher air pressure places the
internal components under loads
and stresses they were not
designed for, causing premature
failure. The air supply should be
clean and dry, preferably
lubricated. For best results, drain
the moisture from your compressor
daily.
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals
known to cause cancer, birth defects or
reproductive harm. Some examples of
these chemicals are:
•Lead from lead-based paints
•Crystalline silica from bricks, cement
and other masonry products
•Arsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals, work in a well-ventilated
area and work with approved safety
equipment such as those dust masks that
are specially designed to filter out
microscopic particles.

UT8965
POSITIVE CLUTCH SCREWDRIVER
UT8965
POSITIVE CLUTCH SCREWDRIVER
Universal Tool’s Limited Warranty
Universal Tool warrants their tools to be free from defects in material and workmanship
for one year from the date of purchase. This warranty does not apply to tools which
have been abused, misused, modified or repaired by someone other than Universal Tool
or their authorized service centers. If a Universal Tool proves defective in material or
workmanship within one year after purchase, return it to any authorized service center
or Universal Tool freight prepaid. Please enclose your name, address and adequate
proof of purchase and a short description of the defect. Universal Tool will, at their
option, repair or replace defective tools, free of charge. Repairs or replacements are
warranted as described above for the remainder of the original warranty period. Univer-
sal Tool’s sole liability and your exclusive remedy under this warranty is limited to repair
or replacement of the defective tool. There are no other warranties expressed or implied
and Universal Tool shall not be liable for incidental, consequential or special damages,
or any other damages, costs or expense of repair or replacement as described above.
Replacement Parts
Ref. Description Part # Ref. Description Part #
Parts Breakdown for UT8965
Specifications
Free speed .................................................................................................................. 1,800 RPM
Bit retainer ............................................................................................ 1/4" Hex Quick Change
Maximum torque ....................................................................................................... 65 in./lbs.
Weight ................................................................................................................................ 2.5lbs.
Overall length ....................................................................................................................... 8.5”
Average air consumption ................................................................................................. 4 CFM
Air inlet .......................................................................................................................... 1/4" NPT
Recommended hose size .............................................................................................. 3/8" I.D.
Maximum air pressure ....................................................................................................... 90 PSI
Tool Operation and Maintenance
•Daily, before putting tool into operation,
disconnect air hose and pour 1/4 oz. of
air tool oil into the air inlet.
•Blow out air line to clear it of accumu-
lated dirt and moisture. Connect tool and
operate momentarily to allow oil to be
carried through tool.
•Hose runs longer than 8 feet should be
connected to a 1/2” ID hose to provide
sufficient volume for proper performance.
•We recommend oil made exclusively for
air tools or equivalents which include
moisture absorbants, rust inhibitors,
metal wetting agents and an EP (extreme
pressure) additive.
1Air Inlet 9389501
2Deflector 9389502
2-1 Gasket 9389502-1
3 Spring 9389503
4 Valve 9328804VN
5 Valve Seat 9328835N
6 Spacer 9328825N
7Sliencer 9389507
8Housing 9389508
9Dowel Pin 9389509
10 Valve Bushing 9389510
11 O-Ring 9389511
12 Reverse Valve 9389512
13 Valve Stem 9389513
13-1 O-Ring 9287617
13-2 Retainer 9389513-2
14 Trigger 9389514
15 Spring Pin 9389515
16 Retainer 9389516
17 Rotor Blades (5) 9389517
18 Ball Bearing 9389518
19 Rear Plate 9389519
20 Rotor 9389520
21 Cylinder 9389521R
21A Pin (2) 9389521A
22 O’Ring 9389522
23 Front Plate 9389523
24 Ball Bearing 9389524
25 Ball Bearing 9389525
26 Washer (2) 9389526
27 Gear Cage 9596527
28 Pinion Gear (2) 9389528
29 Needles (18) 9389529
30 Pin (2) 9389530
31 Ball Bearing 9389531
32 Ring Gear 9389532
33 Gear Case 9596533
34 Clutch (2) 9596534
35 Retainer Ring (2) 9596535
36 Spring 9596536
37 Spacer 9589029N
38 Spindle 9596538
39 Steel Ball 9589046
40 Clutch Case 9596540
40B Anvil Bushing 9589028
41 Bit Retainer Sleeve 9589031
42 Spring 9589043
43 Bit Washer 9589032
44 Bit Ring 9589033