Univex Duro 7510 User manual

INSTRUCTION 7510,7512
MANUAL DURO SERIES Slicer
WE THANK YOU FOR YOUR PURCHASE OF OUR
MODEL 7510, 7512 SLICER.
SINCE 1948
7510/12/1099
ED7

7510/7512
TABLE OF CONTENTS
DESCRIPTION PAGE
Table of Contents 1
List of Illustrations 1
Introduction 3
Installation Instructions 3
Important Safety Warnings 3
Operating Instructions 4
Sharpening Instructions 4-5
Operator's Care of Slicer / Lubrication 5-6
Trouble Shooting Chart 8
Mechanics Maintenance 9
Repair, incl. Disassembly, Replacement and Reassembly 10-12
Replacement of Parts, List 13-26
Warranty Back Cover
LIST OF ILLUSTRATIONS
ILLUSTRATION PAGE
Figure 1 Overall View of Meat Slicer, Model 7510-7512 2
Figure 2 Lubrication Diagram, Model 7510-7512 7
Figure 3 Base and Knife Housing Assembly 13-14
Figure 4 Sharpening Assembly 15
Figure 5 Carnage Assembly, Model 7510 16
Figure 5A Carnage assembly, Model 7512 17
Figure 6 Carnage Ann and Slide Assembly 18
Figure 7 Slice Adjustment Assembly 19
Figure 8 Fence Assembly 20
Figure 9 Motor, Mount and Drive Assembly 115V, 50/60 21-22
Figure 9A Capacitor Panel 100V, 50/60HZ, 1PH 23
Figure 10 Motor, Mount and Drive Assembly 220V, 50HZ 24-25
Figure 10A Capacitor Panel 220-240 V, 50/60HZ, 1PH 26
Figure 11 Electrical Wiring Diagram (115V, 60/50HZ , 1PH) 27
Figure 11 A Electrical Wiring Diagram (220-240V, 50/60HZ, 1PH) 28
Figure 11B Electrical Wiring Diagram (100V, 50/60HZ, 1PH) 29
PAGE 1

7510/7512
OVERALL VIEW OF MEAT SLICER
MODEL 7510 -7512
FIGURE1
1ON-OFF SWITCH 8ADJUSTMENT SPACER
2INDICATOR LIGHT 9ELECTRIC CORD
3CARRIAGE 10 CARRIAGE ARM KNOB
4FENCE 11 CARRIAGE ARM
5LAST SLICE DEVICE 12 REMOVABLE CHEESE SCRAPER
6KNIFE SHARPENER 13 GRADUATED KNOB
7KNIFE GUARD 14 SERIAL NAME PLATE (ON REAR)
PAGE 2

7510/7512
INSTRUCTION MANUAL
INTRODUCTION
This manual contains instructions for the Installation, Operation, Care, Maintenance and Repair of the
Meat Slicing Machine. Disassembly, Replacement and Reassembly Instructions are included. A
trouble shooting
guide is provided. A complete Replacement Parts list with identifying figures is also
included to facilitate identification and ordering of replacement parts.
INSTALLATION INSTRUCTIONS:
INSPECTION
All Univex slicers are inspected and tested at the factory; however, they should be reinspected
carefully by the person making the installation for loose, damaged or broken parts. Detached parts and
fixtures should be checked against packing list to determine all are present. Any damages should be
reported to the Carrier immediately, and any shortages of parts or fixtures reported to Univex
Corporation.
WARNING:
After slicer has been inspected, wash slicer completely with warm water and mild soap.
For SAFETY follow the cleaning instructions on page 5-6.
INSTALLATION:
The most efficient installation of your Univex slicer will depend upon the layout of your kitchen.
Locate your slicer where it will save steps for the operator and be sure to provide sufficient clearance
around it for ease of maintenance and cleaning, as well as for efficient and safe use.
Slicer should be operated on a sturdy bench or table with the height determined to suit the operator. It
is most important that the forearm of the operator be at the proper level for ease and safety of
operation
as well as for maximum production. This height is considered optimum when the carriage
handle (Figure 1 [11])
of the slicer is at approximately the height of the operator's elbow when
standing.
IMPORTANT
WARNING\CAUTION: Electrical wiring instructions are found in the wiring diagram fFig. 11.
Fig.
11 A and Fig. 1
1B). Before making electrical connections, CHECK the
specifications on the name plate to make sure that they agree with those on
your electrical service. A grounding type three terminal plug is p
rovidedfor
safety. If you do not have a mating receptacle, have a qualified electrician
provide grounding provisions in accordance with local safety codes.
IMPORTANT SAFETY WARNINGS
The slicer knife is extremely sharp! Never touch the knife, always keep
hands and fingers clear of the
knife. Never run slicer without the guard or other parts in place and securely fastened. Take extra care
to avoid accidents by keeping the knife guard and sharpening assembly cover ON at all times. When
the machine is not in
use, the slice adjustment knob should be turned back to the closed position
(beyond "0") so that the knife edge is not exposed.
Observe the cleaning instructions on Page 5-6
for best results and for safety. Also remember to always
turn off slicer and disconnect the electrical supply cord.
When slicing, always work the carriage using only the carriage arm handle (Figure 1 [11]).
Do not
hold or push the carriage from any other place.
PAGE 3

7510/7512
OPERATION INSTRUCTIONS
The Univex slicer is designed to meet the Cook's demand for an efficient, sturdy slicer. The Univex
slicer will give unfailing performance over a period of years, when operated and maintained
according to instructions contained herein.
START/STOP SWITCH
The slicer is started by pushing the start/stop toggle switch (Figure 1 [ 1 ])
upwardtotheONposition.
A pilot light (Figure 1 [2]) is provided to indicate when the slicer is turned on.
SLICE ADJUSTMENT
WARNING:
Dial type knob adjustment (Figure 1 [13])
allows for slice thicknesses ranging from
paper thin up to 5/8".
Dial graduations allow you to precisely set up specific slice
thickness for various needs. When not in use, always return knob back to its fully
closed position (beyond "0") so that the knife edge is not exposed.
POSITIVE HOLD CARRIAGE
CAUTION:
A last slice gravity feed grip (Figure 1 [5])
is provided which can be locked out of the
way when not required. Do not use this last slice device to work the carr
iagebackand
forth. Use only the carriage arm handle (Figure 1 [11]).
Always make sure the carriage is positively secured to the slicer by checking to see that the carriage
arm knob (Figure 1 [10]) is fully tightened. Failure to do this could result in t
hecarriagestrikingand
damaging the knife edge.
KNIFE GUARD
WARNING:
The knife guard (Figure 1 [7])
covers the knife edge completely except under the
sharpener cover and the forward edge where slicing will be performed. This forward
edge is covered by the edge of the fence, but only when the slice adjustment is
completely closed.
The knife guard (Figure 1 [7])
can be removed for cleaning by unscrewing the knife
guard knob (Figure 3 [2]).
For safety, keep the knife guard on at all times except when
cleaning. Never operate the slicer with the knife guard removed.
SHARPENING INSTRUCTIONS
This slicer is equipped with a knife having a concave or hollowed rear surface for superior slicing
quality. Of course, any knife however superior must be sharpened re
gularly and properly in order to
produce not only the highest quality slices, but also to allow it to maintain its productivity. The knife
sharpener (Figure 1 [6]) on this machine is a top mounted built-
in design for simplicity and ease of
use. It even has an automatic aligning feature.
WARNING:
The following sharpening procedure will provide high quality sharpening results and
should also be followed for safety considerations:
(1) WARNING: Keep away from the knife edge.
(2) Completely close the slice adjustment (beyond "0") so that the knife edge is not exposed.
(3)
The knife's cutting area should be clean and free from food, especially grease. Grease will ruin the
ability of a grinding stone to sharpen an edge. The stone simply will not cut. If cleaning is
PAGE 4

7510/7512
necessary, follow the procedure outlined on Page 5-6.Remember to unplug the electrical supply cord.
(4) Loosen sharpener lock pin (Figure 3 [4]) which bears against sharpener post, then lift sharpener assembly
(Figure 1 [6]) and rotate it 1/2 turn (180 degrees). Then seat it down over knife.
(5) Tighten sharpener lock pin (Figure 3 [4]). As the lock is tightened, it bears on the sharpener post and
automatically aligns the grinding and debumng stones to the precise orientations which are preset at our
factory.
(6) Turn slicer ON. Depress the sharpener button and hold in which will start the grinding wheel rotating. Run
until the beveled cutting surface cleans up. This can take from30 seconds to several minutes depending on
how dull the blade was allowed to become. Release sharpener button.
(7) Turn slicer OFF and check for the formation of a very slight burr on the side of knife opposite the bevel
which indicates complete grinding of the bevel. This slight burr can be detected either visually of by picking
with a small piece of stiff paper.
(8) Turn slicer ON.Lightly press deburring (honing) button and hold for 1 to 2 seconds while you turnOFFthe
slicer. Blade should now be completely sharpened and honed.
CAUTION: It is very important for best slicing results not to deburr the knife too lone or the keen edge will
be destroyed due to the formation of an undesirable second bevel on the opposite side. This condition tends to
be the primary cause of unsatisfactory slicing results.
(9) Turn slicer OFF. Loosen lock pin,( Figure 3 [4]) then lift and return sharpener to its storage position. Tighten
lock pin.
(10) Clean slicer and knife according to the cleaning procedure on Page 5-6in order to thoroughly remove
grinding debris.
OPERATOR'S CARE OF SLICER
CLEANING
WARNING: 1. Never touch the knife. Always keep your hands, fingers and arms clear of knife.
2. Turn off slicer and DISCONNECT ELECTRICAL CORD (Figure 1 [9]) before cleaning.
Leave protective guard in place.
3. Turn slice adjustment knob (Figure 1 [13]) to the fully closed position (beyond"0") so that the
knife edge is not exposed.
WARNING: 4. Removecarriage assembly (Figure 1 [11]) which may be washed in a sink. Use care in
washing the sharply pointed prongs on the last slice feed grip. (Figure 1 [5]) Wash this area
thoroughly. A small bristle brush is recommended. Use only warm water and mild soap. Rinse
carriage assembly with warm water and dry thoroughly using a clean soft cloth.
Never use detergents nor wash the slicer or any of its parts in a dishwashing machine or the
clear protective finish will be damaged.
PAGE 5

7510/7512
WARNING:
5. Wash body of slicer using warm water and mild soap using a soft clo
th.Under
no circumstances should the slicer be hose rinsed. It is recommended that the
cloth be folded over a thin wooden stick when cleaning between the fence plate
and the knife.
6. Remove knife guard (Figure 1 [7]) by loosening knife guard knob (Figure 3 [2])
and pushing the long stud upward to lift the knife guard above surface of knife.
Then carefully lift and remove guard.
7. Remove Knife deflector (Fig. 3 [19]) by unscrewing Knife deflector screw (Fig.
3 [21]).
WARNING:
8. CAREFULLY wash the
front and rear of the knife with a cloth using warm
water and mild soap. It is recommended that the cloth be folded over a thin
wooden stick as a further caution to avoid accidental contact with the knife.
Rinse with warm water applied with a cloth. Dry th
oroughly with a clean soft
cloth.
WARNING:
9. Following cleaning, a commercial non-toxic sanitizer may be wiped on the
clean surfaces with a soft clean cloth or sprayed as recommended on the
container labeling. It is important that the sanitizer be compat
iblewithanodized
aluminum or the clear protective finish on the slicer will be damaged. Surfaces
should be wetted completely, but not to the point of running or puddling.
WARNING:
10. Replace the knife guard. Never leave the slicer without its knife guardinstalled.
11. Replace Knife deflector.
LUBRICATION
Lubrication instructions are given in Figure 2 on Page 7.
Operator's attention is called to lubricating
the slide bar (Figure 6 [4]) as needed for smooth carriage motion, but at least monthly with
three
drops of mineral oil.
Shafts to the last slice grip and to the auxiliary fence (Figure 5 [7,10]) (Figure 5A[8,12]
should be
lubricated as necessary with petrogel. Distribute over surfaces by moving the grip and fence back and
forth. Wipe excess petrogel, from shafts with a clean cloth.
PAGE 6

7510/7512
LUBRICATION INSTRUCTIONS
MODEL 7510 -7512 FIGURE2
A PETROGEL, AS REQUIRED TO MAINTAIN
LIGHT FILM,
B OIL MONTHLY, THREE DROPS
MINERAL OIL.
PAGE 7

7510/7512
TROUBLESHOOTING GUIDE
7510/7512
TROUBLE POSSIBLE CAUSE REMEDY
1. Slicer will not
operate. 1.1 Electrical service down.
1.2 Burned switch contacts.
1.3 Motor capacitor defective.
1.4 burned out motor
1.1 Check electrical service.
Replace fuse or reset circuit
breaker as necessary.
1.2 clean or replace.
1.3 replace.
1.4 Remove, test, repair or replace
2.
Motor running, blade
not turning. 2.1 Belt tension too tight 2.1 Readjust belt tension.
NOTE: Often after a long period of no use, such as in storage, the belt
flows and takes a set in the pulley ribs. A slight urging of the
knife with a wooden stick will get the slicer turning with no
further problems.
DO NOT USE HANDS TO TURN KNIFE.
3. Slippage of knife
during slicing. 3.1 Loose or broken belt.
3.2 Grease or oil on belt.
3.1 Adjust belt tension or replace
belt.
3.2 Clean pulleys with safety
approved cleaning solvent
on soft clean rag. Replace
belt.
4. Motor stalls during
slicing. 4.1 Knife cutting edge to dull or improperly sharpened.
4.2
Product such as cheese old and
dried out.
4.3 Low voltage service.
4.4 Belt tension
excessive.
4.1 Sharpen using the procedure
specified. Use care not to use
homing stone longer then the
1
or 2 seconds.
4.2 Reduce thickness of slice.
4.3Have electrician check
service voltage.
4.4 Readjust belt tension.
5. Excessive noise. 5.1 Knife contacting the
knife guard.
5.2 Badly worn or frayed
belt.
5.3 Motor pulley and belt
misaligned.
5.4 Loose set screw in motor pulley
5.5 Dirty knife rubbing against
plastic scraper
5.1 Tighten knob which secures
guard.
5.2 Replace belt.
5.3 Realign motor pulley.
5.4 Tighten set screw.
5.5
Clean knife and plastic scraper
6.
Smearing or tearing
when slicing soft
cheese.
6.1 Soft cheese is at room
temperature.
6.2
Knife dirty with hard dried on
product.
6.1
Chill soft cheese for best slicing
results.
6.2 Clean knife thoroughly.
PAGE 8

7510/7512
MECHANIC'S MAINTENANCE
Every year a mechanic or service technician should perform the following inspection and carry out the respective
maintenance as required:
FOR SAFETY, TURN OFF SLICER AND DISCONNECT ELECTRICAL CORD.
1. BELT DRIVE: This drive features a multi-ribbed high performance belt for long trouble-free service. Inspect
belt for proper tension. If glazed or excessively worn, replace. A tensioning device automatically allows for
normal belt wear-in and stretching. However, if addi
tional tension is required, it may be obtained by turning
adjustment nuts (Figure 9/10 [18]) clockwise on take up rod (Figure 9/10 [24]) which will further compress
the tensioning spring. As a guideline, the compressed length of the spring should be approximately 7/8".
2.
MOTOR:
Motor is pre
-
lubricated and requires no periodic maintenance or relubrication in normal kitchen
usage. Provision for re-lubrication in extreme duty applications is provided by means of oiling orifices at
both shaft end and opposite ends of motor. A light weight electric motor oil or #10 non-
detergent oil may be
used.
3. SLICE ADJUSTMENT: Check, by turning the slice adjustment knob (Figure 3 (271) to make sure that the
fence is closing completely (below "0"on knob) and that knife edge is not exposed. If fence is not closing all
the way such that the edge of the knife is exposed, proceed to loosening the lock nut (Figure 7 [29])
and turn
the slice adjustment stop screw (Figure 7 [28]) so the knob can be turned further enough to allow the knife
edge to not be exposed. Now re-tighten the lock nut (Figure 7 [29]). Loosen the two set screws in the slice
adjustment knob (Figure 3 [26]) and re-
adjust its zero position, then tighten the two set screws. Actually, the
closed or zero setposition on the knob should be in the red colored zone of the knob's dial.
4. CARRIAGE: Check for free smooth operation of auxiliary fence, last slice device and for smooth travel of
carnage arm (Figure 6 [19]) Check for excess backlash between slice bearing (Figure 6 [ 14]) and carriage
slide (Figure 6 [7]). The correct lash (clearance) required for smooth carriage operation is obtained when a
very slight lash or movement can be detected. Too much lash can result in the carriage striking and damaging
t
he knife edge. Too little lash results in binding and a loss of smoothness in carriage travel. Lash is adjusted
by loosening locknut (Figure 6 [10]) and turning brass rubbing screw (Figure 6 [11])
clockwise to reduce lash
and counterclockwise to increase lash. Tighten locknut while holding rubbing screw stationary with a
screwdriver so it does not move. Grease only the side of the carriage slide (Figure 6 [7]) on which this brass
rubbing screw slides.
5. LUBRICATION & FUNCTION CHECK: General lubrication should be performed in accordance with the
lubrication instructions in Figure 2.
during this lubrication sequence, be sure to check for free operation and
movement of related parts as well as for excessive wear and looseness of various parts. Be sure to check all
handles and knobs for tightness.
6. KNIFE: Check knife edge to see that it has been properly sharpened. If there is any evidence of incorrect
sharpening procedure, such as excessive honing, alert owner and operator.
PAGE 9

7510/7512
REPAIR INSTRUCTIONS
(including disassembly, replacement and reassembly.)
Always turn off slicer and disconnect electrical cord before doing any maintenance or repair on the slicer. Keep
guards on all times. Keep slice adjustment fully closed so knife edge is not exposed. Keep sharpener assembly also
in place so top of knife edge is not exposed.
DRIVE BELT
1. Disconnect electrical power cord.
2. Remove four rubber suction feet (Figure 3 [37]) that secure bottom cover (Figure 3 [36]) to slicer.
3. Remove nuts (Figure 9 [18]) from tensioning take-up rod (Figure 9 [24]) so motor can be pivoted to give belt
slack. Be careful not to lose tensioning spring (Figure 9 [19]).
4. Note the position of the belt on the pulley to insure proper installation of new belt.
5. Unwrap belt from motor pulley.
6. Reinstall rubber feet (Figure 3 [37]) and place slicer upright (operating position).
7. Loosen sharpener lock pin (Figure 3 [4]). Lift and remove sharpening unit. Set aside.
8. Remove knife guard knob(Figure 3 [2]) and carefully remove knife guard (Figure 3 [14]).
9. Using caution to avoid the sharp knife edge, remove the four screws (Figure 3 [12]) that secure the knife
Carefully remove knife and set aside with its flat side down, flush on a bench so the edge is not exposed.
10. Note the position of the belt on the pulley to insure proper installation of new belt.
11. Unwrap and remove drive belt from the knife pulley (Figure 3 [10]).
12. Wrap replacement belt on knife pulley and motor pulley. Do not reinstall knife at this time.
13. Reinstall spring and nuts on tensioning take up rod (Figure 9 [24]) and tighten. It is important to make sure
that the belt is aligned on both pulleys.
14. Belt tension is correct when the spring is compressed to an overall length of7/8".
15. Connect electrical power and operate slicer to check that belt and pulleys are running true.
16. Disconnect electrical power cord.
17. Reinstall bottom cover and secure with the four suction feet.
18. Using caution, reinstall knife and secure with four screws.
19. Reinstall knife guard and secure with knife guard knob.
20. Reinstall sharpener and secure with lock pin.
PAGE 10

7510/7512
KNIFE (Removal Figure 3)
1. Disconnect electrical power cord.
2. Loosen sharpener lock pin (Figure 3 [4]), then lift and remove sharpening unit. Set aside.
3. Remove knife guard knob (Figure 3 [2]) and carefully remove knife guard (Figure 3 [14]).
4. Using caution to avoid the sharp knife edge, remove the four screws (Figure 3 [12])
that secure knife
(Figure 3 [15]).
5. Carefully remove knife and set aside with its flat side down flush on a bench so the edge is not
exposed.
6. Reinstall new knife in the reverse procedures outlined above.
7. Even though a new knife is very sharp, the sharpening procedure specified on pages 4 and 5 should
be performed to true the new knife's bevel to the slicer.
WARNING: Worn knife should be disposed of in a safe, responsible way, showing concern for other
who may handle it. It is recommended that the edge of the knife be wrapped several time
with heavy tape and that a caution (CAUTION, SHARP EDGE) be written on both sides
of the knife.
KNIFE SEAL(Figure 31
1. Remove knife per above instruction.
2. Unscrew and remove knife insert stud (Figure 3 [16]). Maintain shims that may have been used in
assembly.
3. Using a small screwdriver, carefully pry and remove the knife seal (Figure 3 [11]) from the knife
pulley (Figure 3 [10]).
4. Apply light film of mineral oil on outer diameter and lip of rubber seal.
5. Clean recess in pulley.
6. Drive seal into recess in pulley using care to avoid damage to seal. Seal should be seated uniformly.
7. Check knife insertstud (Figure 3 [16]) for small sharp burrs that may have been raised during its
removal. Remove burrs if present with a fine-toothed file. If burrs are not removed, they will destroy
the seal very quickly.
9. Reinstall knife insert stud and shims that may have been present. Apply three drops of mineral oil to
the seal/stud interface.
11. Reinstall knife, guard and sharpener in the reverse procedure outlined above.
PAGE 11

7510/7512
SHARPENING STONES
1. Disconnect electrical cord.
2. Unscrew sharpener lock pin (Figure 3 [4]).
3. Lift up sharpening assembly (Figure 1 [6]) and remove from slicer.
4. Using an open end wrench, unscrew cover knob (Figure 4 [1]). It is recommended that a piece of tape or paper
be temporarily wrapped around knob prior to unscrewing it so as to protect its finish.
5. Gently remove lever cover (Figure 4 [2]) off of mounting block (Figure 4 [26]). Perform this step slowly taking
care to remove cover evenly from the two locating pins (Figure 4 [9]) on which it fits snugly.
6. Unscrew nut (Figure 4 [21]) and remove along with washer and sharpening stone (Figure 4 [23]).
7. Install new sharpening stone. Flat face should be toward the outside.
8. Re-attach washer and nut.
9. Honing (deburring) stone (Figure 4 [14]) is removed by first unscrewing lock screw (Figure 4 [19]) from
thimble (Figure 4 [18]).
10. Gently remove thimble taking care to not lose the small ball bearing and spring (Figure 4 [16 & 17]) which are
inside.
11. Unscrew nut (Figure 4 [15]) and remove along with washer and honing stone (Figure 4 [14 & 20]).
12. Install new honing stone with the flat face toward the inside.
13, Re-attach washer, nut, and thimble.
14. Re-attach cover and reinstall in the reverse procedures (5.through 1,).
REPLACEMENT OF PARTS LISTS
Replacement parts for the Food Slicing Machine are shown in the following Figures. When ordering replacement
parts, always include the model and serial numbers of the machine in addition to the specific part number.
PAGE 12

7510/7512
BASE AND KNIFE HOUSING ASSEMBLY
MODEL 7510 -7512
FIGURE3
ILLUS. NO. PART NO. DESCRIPTION QTY.
1. 7510012 WASHER, KNIFE 1
2. 7510015 KNOB, KNIFE GUARD 1
3. 7510013 NUT KNIFE 1
4. 7510150 LOCK PIN, SHARPENER 1
5. 7510001 BACK KNIFE GUARD (MODEL 7510) 1
7512001 BACK KNIFE GUARD (MODEL 7512) 1
6. 7510156 WASHER, KNIFE SHIM AS REQ;
7. 7510002 SHAFT, KNIFE 1
8. 7510158 WASHER, KNIFE SHIM AS REQ.
9. 7510004 SPACER 1
10. 7510154 PULLEY, KNIFE 1
11. 6509012 BUSHING, KNIFE 1
12. 6509014 SCREW, BLADE 3
13. 8512240 SCRAPER, BLADE 4
14. 7510011 KNIFE GUARD (MODEL 7510) 1
7512011 KNIFE GUARD (MODEL 7512) 1
15. 7510009 BLADE (MODEL 7510) 1
7512009 BLADE (MODEL 7512) 1
16. 7510008 INSERT, KNIFE7510 1
7512008 INSERT, KNIFE7512 1
17. 1012167 BALL BEARING 2
18. RESERVED
19. 7510022 KNIFE DEFLECTOR 1
20. 8512206 LOCATING PIN 1
21. 7510023 KNIFE DEFLECTOR SCREW 1
22. 7510019 SLICER BODY 1
23. 8512208 GRADUATED KNOB BUSHING 1
24. 8512210 FRONT WHEEL 1
25. 6509098 SET SCREW 1
26. 8512214 SET SCREW 2
27. 7510084 GRADUATED KNOB 1
28. 8512211 REAR WHEEL 1
29. 8512209 RIVET 2
30. 7120009 ON-OFF SWITCH 1
31. 7120009 SWITCH JAM NUT (PART OF SWITCH)
32. 7120011 SWITCH GUARD 1
33. 7120009 SWITCH JAM NUT (PART OF SWITCH)
34. 7120014 INDICATOR LIGHT 115V 1
7120041 INDICATOR LIGHT 220V 1
35. 4400081 SCREW, DOME DRIVE, NO.6 X 5/16 1
36. 7120026 BOTTOM COVER 1
7120126 BOTTOM COVER, 100 V ONLY 1
37. 7510094 RUBBER SUCTION FEET 4
38. 7510014 KNIFE GUARD SHAFT 1
39. 7510021 WASHER, FLAT 2
40. 8512525 LOCK WASHER, EXTERNAL TOOTH M10 2
41. 7510020 SCREW, HEX SOCKET HD M10-1.25 X 25MM 2
42. 7120130 SPACER 100 V ONLY 4
43. 8512326 STUD 100V ONLY 4
44. 4400338 LABEL, DURO (NOT SHOWN) 1
PAGE 13

7510/7512
BASE AND KNIFE HOUSING ASSEMBLY
MODEL 7510 -7512
FIGURE3
PAGE 14

7510/7512
SHARPENER ASSEMBLY
MODEL 7510 -7512
FIGURE4
ILLUS NO. PART NO. DESCRIPTION QTY.
7510151A SHARPENER ASSEMBLY WITH CONER
16509153 KNOB, COVER 1
26509151 COVER, SHARPENER 1
36509150 NUT, COVER SPACER 1
46509149 SPACER. COVER 1
56509125 WASHER, SET PIN 1
66509137 SCREW 1
7 RESERVED
87510120 SET PIN, SHARPENER 1
98512728 PIN, SHARPENER CASTING 2
10 6509147 BOLT, SHARPENER GUIDE 2
11 6509127 SPRING 2
12 6509128 BUSHING 2
13 6509129 STUD, HONING STONE 1
14 6509130 STONE, HONING 1
15 6509131 NUT 1
16 6509134 SPRING 2
17 6509133 BALL 2
18 6509135 BUTTON, DEPRESS 2
19 6509136 SET SCREW, DEPRESS BUTTON 2
20 6509132 WASHER, HONING STONE 1
21 6509143 NUT, SHARPENING STONE 1
22 8512516 WASHER, SHARPENING STONE 1
23 6509142 STONE, SHARPENING 1
24 6509141 STUD, SHARPENING STONE 1
25 6509126A MOUNT, STONE 1
PAGE 15

7510/7512
CARRIAGE ASSEMBLY
MODEL 7510
FIGURE5
ILLUS. NO. PART NO. DESCRIPTION QTY.
1. 8512432 SPACER, ADJUSTMENT 1
2. 8512436 STUD, ADJUSTMENT SPACER 1
3. 6509153 KNOB 3
4. 8512433* BUSHING ADJUSTMENT SPACER 2
5. 8512426 LAST SLICE DEVICE 1
6. 6509054 KNOB, LAST SLICE DEVICE 1
7. 8512428 SHAFT, LAST SLICE DEVICE 1
8. 8512427** BUSHING, LAST SLICE DEVICE 2
9. 8512425 CARRIAGE 1
10. 8512434 SHAFT, ADJUSTMENT SPACER 1
11. 8512431 NYLON TIP 2
12. 6509059 WASHER 1
13. 6509058 BOX NUT 1
14. 1200079 LOCKWASHER 1
15. 8512439 CARRIAGE STUD SCREW 1
16. 8512438 NYLON TIP 1
*Illus 4, 8512433 cannot be purchased separately it is part of illus 1,8512432.
** Illus 8, 8512427 cannot be purchased separately it is part of illus 5, 8512426.
PAGE 16

7510/7512
CARRIAGE ASSEMBLY
MODEL 7512
FIGURE 5A
ILLUS. NO.
PART NO.
DESCRIPTION
QTY.
1.
8512432
SPACER, ADJUSTMENT
1
2. 8512436 STUD, ADJUSTMENT SPACER 1
3. 6509153 KNOB 3
4. 8512433* BUSHING ADJUSTMENT SPACER 2
5. 8512925 SUPPORT, LAST SLICE DEVICE 1
6. 8512924 KNOB, LAST SLICE DEVICE 1
7. 8512926 LAST SLICE DEVICE 1
8. 8512428 SHAFT, LAST SLICE DEVICE 2
9.
8512427**
BUSHING, LAST SLICE DEVICE
1
10. 8512425 CARRIAGE
1
11. 8512438 NYLON TIP, ADJUSTMENT SPACER
1
12. 8512434 SHAFT, ADJUSTMENT SPACER
1
13. 8512431 NYLON TIP, LAST SLICE DEVICE
1
14. 8512927 STUD, CARRIAGE
1
15. 8512229 SCREW, FLAT HEAD
1
16. 6509058 BOX NUT, M10-1.5
1
17. 1200079 LOCKWASHER
1
18. 8512439 WASHER, SPECIAL 1
19.
6509057
STUD, CARRIAGE
1
* Illus 4,
851
2433
cannot be purchased separately it is part of illus
1, 8512432.
** Illus
9, 8512427
cannot be purchased separately it is part of .illus
5, 8512925.
PAGE 17

7510/7512
CARRIAGE ARM AND SLIDE ASSEMBLY
MODEL 7510 -7512
FIGURE6
ILLUS. NO. PART NO. DESCRIPTION QTY.
1. 6509036 WASHER, SLIDE BAR RUBBER 2
2. 7510337. SPRING, SLIDE BAR(7512 ONLY) 2
6509035 SPRING, SLIDE BAR(7510 ONLY) 2
3. 8512229 SCREW, M5-0.8 X 12MM FL HD SLT 2
4. 7510434 BAR, CARRIAGE SLIDE 1
5. 7510326** BUSHING, CARRIAGE ARM 2
6. 7510325 SUPPORT, CARRIAGE ARM 1
7. 7510339 SLIDE, CARRIAGE 1
8. 6509041 WASHER, CARRIAGE SLIDE 2
9. 6509040 BOLT, CARRIAGE SLIDE 2
10. 9512299 BUSHING ECCENTRIC 1
11. 1053510 SCREW, CAP M6-1.0 X 25MM HX HD 1
12. 8512308 SCREW, BEARING LOCKING 1
13. 6509028 WASHER, M8 2
14. 6509031 BEARING 2
15. RESERVED
16. RESERVED
17. 6509037 WASHER 2
18. 6509042 BOLT, CARRIAGE 1
19. 7510043 CARRIAGE ARM 1
20. 6509044 KNOB, CARRIAGE ARM 1
21. 6509045
HANDLE, CARRIAGE ARM
1
22. 6509046 SCREW, CARRIAGE ARM HANDLE 2
23. 8512325 ANCHOR, CARRIAGE 1
24. 8512326 STUD, CARRIAGE ANCHOR 1
** Illus,5 7510326 cannot be purchased separately it is pan of illus 6, 7510325.
PAGE 18

7510/7512
SLICE ADJUSTMENT ASSEMBLY
MODEL 7510 -7512
FIGURE7
ILLUS. NO. PART NO. DESCRIPTION QTY.
1. 7510067 SCREW, SLICE CONTROL ATTACHMENT 2
2. 8512527 SCREW, SLICE CONTROL ATTACHMENT 1
3. 8512526 JIB 1
4. 8512525 WASHER, TOOTHED 2
5. 7510065 SCREW, JIB ATTACHMENT 2
6. 7512076 BOLT, TAPER SUPPORT (7512 ONLY) 1
7510076 BOLT, TAPER SUPPORT (7510 ONLY) 1
7. 8512839 NUT 2
8. 8512522 WASHER 1
9. 6509071 STUD, CRANK 1
10. 8512511 BLOCK, SLICE ADJUSTMENT MOVING 1
11. 8512512 SHAFT, SLICE CONTROL 1
12. 7510073 STUD, JIB ATTACHMENT 1
13. 8512326 STUD 1
14. 6509131 NUT 1
15. 7510061 SPRING 1
16. 8512518 SCREW, SPRING ATTACHMENT 1
17. 6509028 WASHER 2
18. 8512501 PIN, ECCENTRIC 1
19. 8512502 GEAR 1
20. 8512503 WASHER 1
21. 8512504 SCREW, GEAR ATTACHMENT 1
22. 8512510 SHAFT, GRADUATED KNOB 1
23. 6509086 WASHER, FLEXIBLE 1
24. 8512507 WORM GEAR 1
25. 8512506 BALL 1
26. 8512508 ROLL PIN 1
27. 8512505 BALL STUD 1
28. 8512529 SCREW, SLICE ADJUSTMENT STOP 1
29. 8512530 NUT 1
30. 7510060 SLICE CONTROL GUIDE UNIT 1
PAGE 19