UPPAbaby 0317-VIS-AU User manual

Model 0317-VIS-AU | Version 1
USA
UPPAbaby, 60 Sharp Street, Hingham, MA 02043 | uppababy.com | 1.844.823.3132
Australia
Coolkidz Australia Pty Ltd, 37 Malcolm Rd, Braeside, Victoria, Australia 3195 | uppababy.com | 1300 722 302
All rights reserved. © 2016 UPPAbaby. UPPAbaby and all associated logos are trademarks. All product specifications are correct at time of print.
UPPAbaby reserves the right to change anything at any time without prior notice. Color representation is as close as print processes allow.
Not all colors available at all retailers.
0317-VIS-AU__Instructions_V1.indd 2-3 11/2/16 3:51 PM

TABLE OF CONTENTS
Warnings + General Safety Information 2
Cleaning + General Maintenance 5
Parts List 6
Stroller Assembly 7
Bassinet Assembly 9
Bassinet Operation 10
Stroller Operation 13
Limited Warranty 20
Please read these instructions carefully prior to assembly and use.
0317-VIS-AU__Instructions_V1.indd 1-1 11/2/16 3:51 PM

23
WARNINGS + GENERAL SAFETY INFORMATION WARNINGS + GENERAL SAFETY INFORMATION
STROLLER WARNINGS:
WARNING
TO AVOID INJURY OR DEATH:
ALWAYS APPLY THE BRAKES WHENEVER THE PRAM/STROLLER
IS STATIONARY.
•DO NOT LEAVE CHILDREN UNATTENDED.
•SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
•DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/
STROLLER.
•MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS
IF YOU ADJUST THE PRAM/STROLLER.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Please read this manual carefully before using this pram/stroller. Failure
to follow instructions properly may result in serious injury to your child.
• The UPPAbaby VISTA pram/stroller is suitable from 6 months and
designed to accommodate a child up to a weight of 23 kg (50 lbs)
and a height of 101 cm (40"). Excessive weight may cause a hazardous
unstable condition to exist. The product will become unstable if the
manufacturer’s recommended load is exceeded.
• DO NOT use this seat with any other models of stroller.
• Ensure that all the locking devices are engaged before use.
• Any load attached to the handle aects the stability of the pram/stroller.
• Unit may become unstable if the manufacturer’s recommended load
is exceeded, or if a parcel bag, accessory, or rack other than that
recommended by the manufacturer is used or hung from the unit.
• It is unsafe to use accessories other than those approved by UPPAbaby.
• Extreme care should be taken if the pram/stroller is used on stairs or
an escalator.
• The pram/stroller should not be used near an open fire or exposed flame.
• Maximum weight for the storage basket is 13.6 kg (30 lbs).
WARNING
• Always use the crotch strap in combination with the waist belt and
shoulder belts.
• NEVER leave safety harness connected when not fitted to a child in the
stroller as this may create loops that could cause a strangulation hazard.
• The brake must be locked while taking the child in or out of the pram/
stroller, and when parked.
• The pram/stroller is designed for use on flat or gently sloping surfaces
and may be unstable on higher sloping and uneven surfaces and could tip
over if on sloping, unstable or uneven surfaces.
• Always use the tether strap to prevent the pram/stroller from rolling away.
• Bumper bar must be attached at all times.
• DO NOT lift the stroller by the bumper bar as it may disengage.
• Children and adults should be clear of moving parts while making pram/
stroller adjustments. If not properly executed, damage to fingers or
extremities may occur when opening or closing the pram/stroller frame.
• Make sure latch on left side of stroller is properly engaged after
stroller is folded. Carry grip on side of stroller should be used for
ease of transport.
BASSINET WARNINGS:
WARNING
• DO NOT let other children play unattended near the bassinet.
• Audible “click” must be heard in order to determine that each lock is in
the proper position. To ensure proper locking engagement, check to see
that the bassinet handle cannot be disengaged from the pram without
unlocking the device, and/or indicator on sides of bassinet is green.
• This product is suitable only for a child who cannot sit up unaided,
roll over and cannot push itself up on its hands and knees.
• Maximum weight of the child: 9 kg (20 lbs). Maximum child height:
63 cm (25").
• For extended sleep, make sure canopy is raised and locked in upright
open position.
0317-VIS-AU__Instructions_V1.indd 2-3 11/2/16 3:51 PM

45
WARNINGS + GENERAL SAFETY INFORMATION
CLEANING:
• Clean frame with a damp cloth and a mild detergent; dry thoroughly. DO NOT use abrasives.
• If the stroller chassis parts have been exposed to salt water we recommend that they be rinsed
with fresh (tap) water as soon as possible to avoid corrosion. Always dry frame if wet.
• All fabrics are removable.
• To extend the life of your VISTA’s fabric, keep it clean and do not leave it in direct sunlight for
long periods of time.
• DO NOT fold or store the VISTA if it is damp or wet, nor store in a damp environment.
MAINTENANCE AND REPAIR:
• This pram/stroller requires regular user maintenance. Regularly check all connecting hardware
(rivets, screws, etc.) for tightness and security.
• Inspect your VISTA periodically. Seek prompt repairs, replacing worn or broken parts as needed.
Check all safety devices, locks and harnesses for correct and secure operation. Never continue
to use a product that is structurally unsound.
• Only UPPAbaby replacement parts should be used. It may be unsafe to use parts supplied by
another manufacturer.
• Do not make any alterations or modifications to the stroller with products not supplied by the
manufacturer as this may cause instability or structural damage not covered under warranty.
• Please contact Customer Service with any repair questions.
CLEANING + GENERAL MAINTENANCE
CLEANING SEAT, OUTER BASSINET, CANOPY FABRICS AND BUMPER BAR COVER
CLEANING INNER BASSINET FABRICS
Spot clean or hand wash gently
in cold water with mild detergent.
30C
Machine wash cold gentle cycle
with mild detergent.
Dry flat and away from direct
sunlight before re-use or storage.
Dry flat and away from direct
sunlight before re-use or storage.
DO NOT bleach,
iron or dry clean.
DO NOT bleach,
iron or dry clean..
WARNING
SUFFOCATION HAZARD
• Infants can suocate in gaps between an extra pad and side of bassinet
or on soft bedding.
• NEVER add a mattress, pillow, comforter, or padding. Use ONLY the pad
provided by the manufacturer.
• Infants can roll over on soft surfaces and suocate child. NEVER place
bassinet on beds, sofas, or other soft surfaces.
• To reduce the risk of SIDS Pediatricians recommend healthy infants be
placed on their backs to sleep, unless otherwise advised by a Physician.
• DO NOT allow any part of sunshade or bassinet storage bag to cover a
child’s nose or mouth
WARNING
FALL HAZARD
• To prevent falls, do not use this product when the infant begins to push
up on hands and knees or has reached manufacturer’s recommended
maximum weight, whichever comes first.
• Child’s movement can slide bassinet. NEVER place bassinet near edges of
counter tops, tables, or other elevated surface.
• Use only on a firm ground which is horizontal, level and dry when not in
use with the pram/stroller.
• If the bassinet is intended to be used with a stand, check that the
dimensions of the latter correspond to those of the bassinet base
(36 cm w x 69.9 cm h).
• This bassinet is designed to be used with the UPPAbaby VISTA stroller
and UPPAbaby VISTA bassinet stand only.
• NEVER use the bassinet as a means to transport an infant in a motor vehicle.
• To avoid serious injury or death to your child, do not use this bassinet
as a car bed.
• Use of bassinet cover is recommended for added safety of your child.
Manufactured to comply with: AS/NZS 2088:2013.
CLEANING LEATHER BUMPER BAR COVER
Spot clean with a damp cloth.
DO NOT wet excessively.
DO NOT bleach, iron or dry clean.
0317-VIS-AU__Instructions_V1.indd 4-5 11/2/16 3:51 PM

67
STEP 2: Pull handle upward until frame locks open,
STEP 1: Push latch back with your thumb to release
locking mechanism.
STROLLER ASSEMBLY
UNFOLDING THE STROLLER
Toddler Seat
Rain Shield
Toddler Seat
Bug Shield
Bassinet
Bug Shield
Bassinet Storage Bag To Install Back Wheels: While pressing in hubcap,
slide wheel onto axle until it locks into place.
To Remove Back Wheels: Push the hubcap in and
pull the wheel out .
INSTALLING FRONT/BACK WHEELS
To Remove Front Wheels: Slide plastic lever
clockwise and pull the wheel out .
To Install Front Wheels: Slide wheel post into housing
until it locks into place.
Stroller
Frame
Telescoping
Handlebar
Back
Wheels
Canopy
PARTS LIST
Front
Wheels
Bassinet
Cover
Bassinet
Bassinet
Canopy
Mattress
+ Mattress
Cover
Bumper Bar
with Cover
BasketSeat
0317-VIS-AU__Instructions_V1.indd 6-7 11/2/16 3:51 PM

89
ATTACHING/REMOVING THE SEAT
CANOPY INSTALLATION
STEP 1: Insert metal posts into bumper bar
attachment slots found on both sides of seat.
STEP 2: To remove, press button at bottom of plastic
housing and lift bumper bar out .
STROLLER ASSEMBLY BASSINET ASSEMBLY
ATTACHING/REMOVING THE BUMPER BAR
To Attach Seat: Lower seat onto frame in forward or reverse position
and press down until it clicks into place. Pull up on seat to ensure it is
locked to frame.
To Remove Seat: Simultaneously
push down release buttons
and lift seat from frame .
STEP 2: Snap each side of canopy attachment to
seat frame.
STEP 1: Pull canopy fabric over seat back recline
button.
STEP 1: Remove mattress.
STEP 3: Pull bassinet canopy handle upright until an
audible “click” is heard.
STEP 2: Pull both steel braces firmly towards the outer
ends of the bassinet into their respective sockets.
Make sure both braces are properly locked in place.
STEP 4: Zip bassinet cover onto bassinet frame.
SETTING UP THE BASSINET
0317-VIS-AU__Instructions_V1.indd 8-9 11/2/16 3:51 PM

10 11
BASSINET OPERATION
To Attach Bassinet to Stroller Frame: Guide the
bassinet hubs over the posts on the stroller frame.
Push until you hear a “click” on both sides.
NOTE: Check that safety indicator is green to ensure
bassinet is properly installed.
To Remove Bassinet from Stroller Frame: Slide plastic
button on carry handle in the direction indicated
and press down to release bassinet. Lift bassinet o
frame using carry handle.
ATTACHING BASSINET TO STROLLER FRAME
CANOPY VENTILATION
STEP 2: Lift and line up seam
half-way until magnets connect.
STEP 2: Pull canopy support frame
from hub on one side.
STEP 1: Unzip the bottom zipper
on the canopy hood.
STEP 1: Unzip canopy zippers
located on the underside of canopy
where fabric meets the carry handle.
For Additional Ventilation: Undo
Velcro flap found on bottom
exterior of bassinet and adhere
to lower Velcro strip.
STEP 3: Detach support frame from
rear clip.
BASSINET OPERATION
STEP 1: Collapse bassinet canopy by simultaneously
pressing buttons on both sides and pushing back.
Using Bassinet Storage Bag: Slide collapsed bassinet
into bag and fasten Velcro tab.
Step 4: Slide fabric o canopy support frame.STEP 2: Lift mattress out of the way. Disengage by
pulling steel braces from their respective sockets.
Proper Use of Bassinet Bug Shield
To Remove Bassinet Fabric: Unzip liner from interior
bassinet frame.
COLLAPSING BASSINET
PROPER USE OF ACCESSORIES
REMOVING BASSINET FABRICS
0317-VIS-AU__Instructions_V1.indd 10-11 11/2/16 3:51 PM

12 13
STROLLER OPERATION
SETTING THE SWIVEL/LOCKING SYSTEM
To Lock Front Wheel Swivel: Push grey button
down to activate lock.
To Unlock Front Wheel Swivel: Push grey button
down again to deactivate lock.
SETTING THE BRAKE
To Lock Brake: Push down pedal with foot to lock.
NOTE: Check that safety indicator is RED to ensure
lock is engaged.
To Release Brake: Push pedal down again to release.
NOTE: Safety indicator will return to GREEN.
BASSINET OPERATION
USING THE BASSINET FOR EXTENDED SLEEP
STEP 2: Use UPPAbaby Bassinet Stand which creates
a secure, elevated fixture.
STEP 4: Ventilate canopy by unzipping hood and
lifting seam half way to secure with magnets.
STEP 1: Undo Velcro®flap to ventilate bottom of
bassinet.
STEP 3: Raise canopy to upright open position.
NOTE: If you choose to have canopy down, secure extended sunshade with toggle button to elastic.
0317-VIS-AU__Instructions_V1.indd 12-13 11/2/16 3:51 PM

14 15
To Lock the Harness: Slide belt ends into center lock
housing until it clicks together.
To Unlock the Harness: Depress grey button at center
and pull apart.
STROLLER OPERATION
OPERATING THE SEAT HARNESS
STEP 1: Detach grey adjustment ring from harness
attachment loop.
STEP 2: Reattach clip to the desired harness loop.
ADJUSTING SHOULDER HARNESS HEIGHT
NOTE: Use loop location above child’s shoulder line, or closest to child’s shoulder.
STROLLER OPERATION
ADJUSTING HANDLE HEIGHT + LEG REST
ADJUSTING CANOPY
RECLINING SEAT
To Adjust Handle: Squeeze button at top and slide
handle to one of three desired positions suited to
user height and comfort.
To Adjust Canopy: Slide canopy
attachment simultaneously
up as far as possible to lock in
highest position.
To Use Sunshade: Pull sunshade
out for SPF 50 sun protection.
To Use Peek-a-boo Window:
Roll flap and secure toggle button
to elastic.
To Adjust Leg Rest: Simultaneously push buttons on
sides of leg rest and rotate to desired position.
To Recline Seat: Engage button on seat back and tilt
seat to desired position. Release button to lock in
one of five preset positions.
NOTE: DO NOT use upright position for infants less
than six months old. Use the most reclined position
and gradually reposition seat upright as child
is able to support his or her head without assistance.
0317-VIS-AU__Instructions_V1.indd 14-15 11/2/16 3:52 PM

16 17
STROLLER OPERATION
STEP 1: Activate brake to prevent stroller from rolling
forward while folding.
STEP 3: Place index fingers on both slide release
triggers and slide upward until frame begins to fold.
STEP 5: Continue to fold stroller until latch on left
side has engaged.
STEP 2: Engage button on top of handle bar and
extend to highest position.
NOTE: Handle must be in highest position for stroller
to stand when folded.
STEP 4: Once stroller begins to fold, hold handle bar
with right hand and reposition left hand onto back leg.
FOLDING THE STROLER
NOTE: When folding frame with seat attached, seat must be in forward facing and upright position.
NOTE: Stroller
will stand when
folded.
Proper Installation of Rain Shield Proper Installation of Bug Shield
STROLLER OPERATION
CORRECT ATTACHMENT OF ACCESSORIES
CORRECT USE OF TETHER STRAP
NOTE: A tether strap is fitted to this stroller. Place the
loop over left wrist when using the stroller.
0317-VIS-AU__Instructions_V1.indd 17 11/2/16 3:52 PM

18 19
STROLLER OPERATION
REMOVING FABRICS FROM CANOPY
STEP 1: Lift canopy fabric up to view canopy support
frames and canopy mounting bracket from interior of
canopy.
NOTE: Front rounded canopy support frame ,
middle support frame and back support frame
attached to mounting bracket .
STEP 2: Flip canopy over to outside view. With a
small screw driver, push tabs in opening on hinges in
and pull canopy support frames and out.
STEP 3: Remove back canopy support frame
from canopy mounting bracket by sliding it upward.
STEP 4: Slide canopy fabric o of all three exposed
canopy support frames.
NOTE: Reverse steps when replacing canopy.
NOTE: Remove canopy from toddler seat prior to removing canopy fabric.
STROLLER OPERATION
STEP 1: Unfasten elastic loops from lower footrest.
STEP 3: Unsnap nylon webbing from frame.
STEP 2: Unzip retainer pocket located on underside
of seat.
STEP 4: Remove seat fabric from frame.
REMOVING FABRICS FROM SEAT
NOTE: Reverse steps when replacing seat fabric.
0317-VIS-AU__Instructions_V1.indd 18-19 11/2/16 3:52 PM

20
Your UPPAbaby is warranted to be free from any manufacturing defects for a period of 2
years from the date of purchase under normal use and in compliance with the operating
instructions.
This warranty is not transferable and extends only to the original retail purchaser and
is only valid when supplied with proof of purchase. PLEASE RETAIN PROOF OF
PURCHASE FOR THIS LIMITED WARRANTY.
The warranty is valid only in the original country of purchase. This warranty is subject
to the conditions set forth by country in which the items were purchased. Conditions
may vary. UPPAbaby will not ship replacement or repair parts out of the country
of purchase.
UPPAbaby will provide replacement parts or conduct repairs as determined fitting by
the company. UPPAbaby reserves the right to exchange item with a replacement part.
Some parts may be replaced with newer model parts as the product is improved over time.
Please NOTE that a repair issue will NOT be covered by this warranty if:
• The issue is caused by misuse or poor maintenance. Please refer to this instruction
booklet for guidance on product use and maintenance.
• Damage is caused by improper installation of UPPAbaby parts and/or accessories.
Please refer to this instruction booklet for guidance on item use and maintenance.
• Damage is corrosion, mold or rust caused by lack of maintenance or service.
• Damage is due to general wear and tear, which is the result of everyday use or negligence.
• Damage is caused by sun intensity, sweat, detergents, damp storage or frequent washings.
• Repairs or modifications are carried out by a third party.
• Product is purchased from an unauthorised retailer. Approved retailers are listed on our
website at uppababy.com.
• Product is second-hand.
• Product is damaged as a result of an accident, airline or freight damage.
UPPAbaby reserves the right to determine if warranty terms and conditions have been met.
Please contact your local distributor if you have any questions regarding warranty.
LIMITED WARRANTY
UPPAbaby oers an EXTENDED 1 YEAR WARRANTY
(for a total of 3 years) on all pushchairs, car seats and
select accessories (Bassinet, RumbleSeat, and PiggyBack).
Register your product at: uppababy.com
To receive the additional 1 year warranty, customers must register their product
online at uppababy.com within 3 months of purchase and provide a valid proof
of purchase. Extended warranty applies only to 2015 and later product models.
0317-VIS-AU__Instructions_V1.indd 20-21 11/2/16 3:52 PM