UREVO Strol Lite 2-in-1 User manual

IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference.
The specications of this product may vary from this photo, subject to change without notice.
Manufacturer:Shanghai Runmi Technology Co., Ltd.
Address:15th Floor, Building 21B, No.1158, Zhongxin Rd,
Songjiang district, Shanghai, P.R.China
Version: 9.0 MADE IN CHINA
Strol Lite 2-in-1
Under Desk Treadmill
USER MANUAL
Model.UR9TM0011

Strol Lite 2-in-1
Under Desk Treadmill
USER MANUAL
Model.UR9TM0011

TABLE OF
CONTENTS
02 CUSTOMER SERVICE
03 IMPORTANT SAFETY INSTRUCTIONS
05 PRODUCT AND ACCESSORIES
06 SPECIFICATION
07 PRODUCT INTRODUCTION
08 HOW TO USE
10 OPERATION
12 CARE AND MAINTENANCE
14 ERROR CODE
15 TROUBLESHOOTING
16 WARRANTY

02
1CUSTOMER SERVICE
IMPORTANT: FOR UREVO ONLY
For damaged or defective product, questions, replacement parts or any other service
support, please contact our customer service department by the below methods:
[email protected]
Response Time: 24-48 hours
Emailing us with the Order ID will be the best method to receive a response during peak
business hours.
Website: www.urevosports.com
US Support Hotline: [phone]
Hours of Operation: Monday – Friday : 9 AM – 12 PM ; 1 PM – 6 PM (PST)
PLEASE DO NOT RETURN THIS PRODUCT WITHOUT ASKING OUR CUSTOMER SERVICE
FIRST.
Scan this QR code to get the product installation guide
YouTube Video

03
DANGER - To reduce the risk of
electric shock:
1.Always unplug this treadmill from the
electrical outlet immediately after using
and before cleaning.
WARNING - To reduce the risk of
burns, re, electric shock, or injury
to persons:
1.An treadmill should never be left
unattended plugged in. Unplug from
outlet when not in use,and before
putting on or taking o parts.
2. Do not operate under blanket or pillow.
Excessive heating can occur and cause
re, electric shock, or injury to persons.
3.Close supervision is necessary when
this treadmill is used by, on, or near
children, invalids, or disabled persons.
4.Use this treadmill only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
5.Never operate this treadmill if it has
a damaged cord or plug, if it is not
working properly, if it has been dropped
or damaged, or dropped into water.
Return the treadmill to a service center
for examination and repair.
6.Do not carry this treadmill by supply
cord or use cord as a handle.
7.Keep the cord away from heated
surfaces.
8. Never operate the treadmill with the
air openings blocked. Keep the air
openings free of lint, hair, and the like.
9. Never drop or insert any object into
any opening.
10. Do not use outdoors.
11. Do not operate where aerosol (spray)
products are being used or where
oxygen is being administered.
12. Caution - To reduce the risk of injury
from moving parts - Unplug before
servicing.
13. Warning - To reduce the risk of Electric
shock - Unplug before cleaning or
servicing.
14. Warning - Risk of personal injury -
Keep children under the age of 13
away from machine.
15. To disconnect, turn all controls to
the position, then remove plug form
outlet.
16. Connect this treadmill to a properly
outlet only. See grounding
instructions.
17. This treadmill is not intended for use
by persons with reduces physical,
sensory or mental capabilities, or lack
of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the
treadmill by a person responsible for
their safety. Keep children under the
age of 13 away from this machine.
18. The maximum weight capacity for
this product is 265lbs/120kg. DO
NOT EXCEED MAXIMUM WEIGHT
CAPACITY.
SAVE THESE
INSTRUCTIONS
2IMPORTANT SAFETY
INSTRUCTIONS

04
GROUNDING INSTRUCTIONS:
This product must be grounded. If it should
malfunction or breakdown, grounding
provides a path of least resistance for
electric current to reduce the risk of electric
and a grounding plug. The plug must
be plugged into an appropriate outlet
that is properly installed and grounded
in accordance with all local codes and
ordinances.
DANGER - Improper connection of the
equipment-grounding conductor can
result in a risk of electric shock. Check
with a qualied electrician or serviceman
if you are in doubt as to whether the
product is properly grounded. Do not
modify the plug provided with the product
- if it will not t the outlet, have a proper
outlet installed by a qualied electrician.
FCC STATEMENT：
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
(3) This device has been evaluated to
meet general RF exposure requirement.
The device can be used in portable
exposure condition without restriction.
Note:This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
This Class B digital apparatus complies
with Canadian ICES-003.
Cetappareilnumerique de la classe B
estconforme a la norme NMB-003 du
Canada.

05
3PRODUCT AND
ACCESSORIES
Please carefully check whether the contents of the package are complete and intact.
If there is any missing and damage, please contact the seller.
Treadmill × 1
CR2450
3V
Hex Tool × 1
Accessories
Remote Controller
x 1
Power cord x 1 Lubricating oil x 1
User Manual x 1
Extra Battery x 1

06
4SPECIFICATION
Product
conguration Detailed
parameters
Product
conguration
Detailed
parameters
Product dimension
(Folding)
138.9 × 67.1 × 13.0 cm
Product dimension
(Assembly)
133.6 × 67.1 × 100.8 cm
54.7 x 26.4 x 5.1 inch 52.6 x 26.4 x 39.7 inch
Running Area
43.2 x 108.0 cm
Minimum speed 0.6 mph
17 x 42.5 inch
Gross weight
31 KG
Maximum speed 7.6 mph
68.4 Lbs
Net weight
26 KG Rate voltage 110 - 120V ~
57.3 Lbs Peak horsepower 2.5 hp
Maximum load
120 KG Rated power 0.75 hp
265 Lbs Suggested age 14-60 years old

07
5PRODUCT
INTRODUCTION
Power Connector
Console
Upright
Remote Controller
Main Body
Lock Dail
Foot Rail
Motor Hood
Running Belt
Emergency Stop Button
Idler Roller
cover-right
Display Panel
Transport Wheel
Idler Roller
cover-left

08
6HOW TO USE
Unfolded to run
1.Open the packaging box and take
out the treadmill with the related
accessories from the box.
2. Lift up handrail untill end position.
3.Turnning side lock dail to the OFF
postion (same operation on both sides).
NOTE : Handrail MUST xed security
before running.
Tighten
4.Plug in power cord to power connector.
5.Power on and start running.
Power Switch

09
Folded to walk
1.Turnning side lock dail to the ON position.
2. Fold down handrail untill in lined with foot rail.
3.Start to walk mode with remote control.
Moving
1. If transportation needs, unplug power cord and lifting the terminal of treadmill.
2. Easy to transport treadmill with bottom transportation wheel assists, like as wheelbarrow.
NOTE : Before move and storage, please make sure the power switch is o and power
cord is unplugged.

10
7OPERATION
Console
Mobile Phone Placement Slot
Emergency Stop Key (STOP)
S TO P
Button Function
Button Function
Emergency Stop.
Short or long press this button to decelerate at per 0.2 miles.
Speed shortcut button: Press this button directly to adjust the speed to
3mph.
• Short press this button to start the treadmill at the speed of 0.6 mhp.
• Short press this button to have a pause as you exercise.
To resume workout, re-press it again.
Short press this button to stop the treadmill in running mode.
Speed shortcut button: Press this button directly to adjust the speed to 6mph.
Short or long press this button to accelerate at per 0.2 miles.
Note: In standby mode, the screen will automatically turn off in case non-activated
console longer than 5 minutes, you’re able to weak up screen by press any of buttons.

11
Display Screen
kcal min
Speed Calories
Infrared receiver port
DistanceTime
Name Range Display
Speed 0.6-7.6 mph The speed of walking belt;
Calories 0001-9999 Kcal The approximate number of calories of you have burned;
Time 01-99 minutes • The time elapsed time ;
• Autonomy stop after 99 minutes Non-stop exercising.
Distance 00.00-99.99miles The distance that you have walked or run;
Infrared
receiver port /Aiming the receiver when remote control in use.
Remote Control
Accelerate
Decelerate
Start/Pause/Stop
• Press button to start walking belt, the default
initial speed setting is 0.6 miles.
• Press button to have a pause in working mode,
to resume workout, re-press it again.
• Hold press this button to stop walking belt
when your workout is completed.
• Short or long press this key to aecelerate at
per 0.2 miles.
Short or long press this key to decelerate at
per 0.2 miles.
Note: The speed can only be accelerated to 3.8 mph via the remote control.
To accelerate to 7.6 mph, you need to press “+” button on the console.

12
8CARE AND
MAINTENANCE
Symptom : walk belt o centered or slips.
Figure 1
Figure 2
Figure.3
Centering walk belt process as follow :
1.Power o treadmill and unplug the power cord .
2. Manual centering process as follow:
• If the walk belt has shifted to left, use the hex tool
to turn the left idler roller screw clockwise 1/4 of a
turn(refer to gure 1).
• If the walk belt has shifted to right, use the hex tool
to turn the right idler roller screw clockwise 1/4 of
turn(refer to gure 2).
3. Treadmill MUST work 1-2mintutes. Repeat manual
centering process untill the walk belt is centered.
Belt slip correcting process as follow :
1.Power o treadmill before operation.
2. Using the hex tool, turn both idler roller screws
clockwise 1/2 of turn(refer to gure 3).
3.After corrected, please attempts to walking 1-2
minutes under 0.6mph speed setting. Repeat until the
walk belt is properly tightened.
Note: The Tread-belt should not be adjusted too
tightly, otherwise it will be damaged.
Attentions
1.To prevent any injury, don’t place any debris around
treadmill before maintenance process.
2. MUST use associated hex tool.
3. Take care at maintenance process.
Do not pinch ngers.

13
Belt lubrication process, follow instruction below to
lubricate belt.
1. Power o appliance and unplug cord.
2. Using the hex tool, turn both idler roller screws
counterclockwise till belt loosen and lifting easily.
Tips: please markdown hex tool rotating cycles
when loosen belt, which use for adapting belt
tension after lubrication process.
3. Lifting edges of belt and spraying lubrication oil at
center of walk platform evenly. Not necessary to
apply spray lubrication oil on entire walk platform.
4. Lubrication oil volume Per time of maintenance:
5-10mL.
Attention: it would causes of belt slip if spray too
much.
5. Using the hex tool, turn the both idler screws
clockwise as previous markdown number of turns
untill walk belt tighten properly.
6. Power on appliance and workout for a few minutes,
in order to spread lubrication oil to whole belt surface
evenly.
Lubrication frequency: High recommend 125 Miles
Per time.
Treadmill cleaning.
1.Power o treadmill and unplug power cord before
cleaning.
2. Wipe and clean with damp cloth, Do not cleaning with
acidic or caustic detergents.
3.Do not clean opposite of walk belt.
4.Its normal few black powders residual under treadmill
after long working.

14
9ERROR CODE
Error Code Fault Analysis Resolutions
E01
Communcation
interrupted between
contoller and numercic
display.
Unscrew motor hood and verify connection
between controller and numeric display.
Please contact with after sale service if E01
code has not been eliminated.
Notice: Always power o and unplug power
cord before processing.
E02 Flame protection
1.Unscrew motor hood and verify connection
between controller and motor.
2. Power supply interrput due to connector
loosen or out, please unscrew motor hood
to check.
3.Please contact with after sale service if
problem CAN NOT solved by above process.
E05
Over current protection
1.Due to user over limited 120Kg.
2. Open to check any foreign objects blocked
moving parts. ( such as: drive motor, idler
roller, driver roller, walking belt )
3.Walking belt is overtightened or lack of
lubricant. ( please see detail chapters relate
to belt tension and lubricant process )
E06
E07 Software bug Replace new controller.
E10
Communcation
interrupted between signal
cable and console.
1.Unscrew console box and verify connection
between singal cable and console.
2. Unscrew console box and verify internal lead
wires whether are damaged or pierced.
3.Replace new console PCBA board.
Once error code happened, you MUST stop workout immediately, Please contact with after
sale service if problem CAN NOT be solved after restart.

15
10 TROUBLESHOOTING
Problem Fault Analysis Resolutions
No working
1.Power rock switch
dyfunction
2. Power supply
interrputed.
3.Power cord damaged
1.Replace new power rock switch if it doesn't
light on.
2. Make sure that power cord is plugged into
properly grounded outlet.
3.Replace new power cable.
Walking
belt slips Walking belt loosen Tighten walking belt tension with hex tool ( 1/4 a turn both idler roller screw clockwise)
Remote
control
does not
work
1.Incorrect use of default
2. Battery power shortage.
3.Remote control
maulfunction
1.Remotor control should directly aiming to
receiver port when in use.
2. Replace new battery cells.
3.Replace new remote control.
Friction
noise Walking belt o center. See details of walking belt tension chapter.

16
11 WARRANTY
MANUFACTURER’S LIMITED WARRANTY
UREVO warrants to the original purchaser that this product is free from defects in material
and workmanship when used for the purpose intended, under the conditions that it has
been installed and operated in accordance with UREVO Owner’s Manual. UREVO’s obligation
under this warranty applies to the following:
COMPONENT LENGTH OF WARRANTY
Structural Frame 1 year For Home Use Only
All Other Components 90 days For Home Use Only
Exclusions from Warranty Coverage:
UREVO does not warrant against and is not responsible for, and no implied warranty shall
be deemed to cover, any product failure, product malfunction, or damages attributable to:
1.Improper installation and/or failure to abide by UREVO’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it was not
designed;
3.Cosmetic items such as scratches, dents or discolorations;
4.Damage caused by normal wear and tear, vandalism, accidental or by animals;
5.Any act of Nature (such as re, ooding, snow, ice, hurricanes, earthquakes, lightnings
or other natural disasters), environmental condition (such as air pollution, mold, mildew,
etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
6. Normal weathering due to exposure to sunlight, weather and atmosphere which can cause
colored surfaces to among other things, ake, chalk, accumulate dirt or stains.
7.Improper operation, alteration, handling, storage, abuse or neglect of the products.
UREVO , using its sole discretion, will either repair or replace free of charge any part(s)
proven to be defective under normal home use. Any repair or replacement shall provide
no new warranty coverage, but shall retain only the remaining portion of the original
product’s warranty. This warranty is oered only to the original purchaser and is not
transferable. Proof of original purchase is required.
When ordering replacement parts please have the following information ready:
1. Order Number
2. Description of Parts
(Adding photos or videos would be helpful)
3. Part Number
4. Date of Purchase