urmet domus 1099 User manual

DS1099-014A
Mod.
1099
H.265 1080P IP Cameras
IP Bullet Camera Ref. 1099/200 Starlight IP Bullet Camera Ref. 1099/201
IP Bullet Camera Ref. 1099/202 Starlight IP Bullet Camera Ref. 1099/203
IP Dome Camera 1099/300 Starlight IP Dome Camera 1099/301
IP Dome Camera 1099/302 Starlight IP Dome Camera 1099/303
Vandal IP Dome 1099/304
USER MANUAL

DS1099-014A 2

CONTENTS
1 Introduction................................................................................................................................................4
2 Product Description ..................................................................................................................................5
2.1 Technical characteristics ...........................................................................................................5
2.2 Opening the Box........................................................................................................................5
2.3 Warnings ...................................................................................................................................6
3 Overview.....................................................................................................................................................8
3.1 Range of Application .................................................................................................................8
3.2 Product description....................................................................................................................8
3.3 Operating environment ..............................................................................................................9
4 Device Connection ................................................................................................................................. 10
4.1 IP Camera Connector Layout (Where present)...................................................................... 10
5 Operating instructions ........................................................................................................................... 10
5.1 Check Connection .................................................................................................................. 11
5.2 Searching for the Device ........................................................................................................ 11
5.3 Installation of Controls and Login to the System.................................................................... 12
6 Login........................................................................................................................................................ 13
6.1 Preview ................................................................................................................................... 13
7 Live .......................................................................................................................................................... 13
7.1 PTZ Control ............................................................................................................................ 14
8 Local settings ......................................................................................................................................... 16
9 Playback .................................................................................................................................................. 17
10 Remote Setting ....................................................................................................................................... 18
10.1 Display Configuration ............................................................................................................. 18
10.1.1 Live .............................................................................................................................................................18
10.1.2 Image Control .............................................................................................................................................19
10.1.1 Privacy Zone...............................................................................................................................................20
10.1.2 ROI .............................................................................................................................................................20
10.2 Record Parameters ................................................................................................................ 21
10.2.1 Rec Parameters ..........................................................................................................................................21
10.2.2 Schedule.....................................................................................................................................................21
10.3 Network .................................................................................................................................. 21
10.3.1 Network.......................................................................................................................................................21
10.3.2 Video Streaming .........................................................................................................................................23
10.3.3 E-Mail Configuration ...................................................................................................................................24
10.3.4 DDNS Configuration ...................................................................................................................................25
10.3.5 IP Filter .......................................................................................................................................................26
10.3.6 RTSP ..........................................................................................................................................................26
10.3.7 FTP.............................................................................................................................................................27
10.4 Alarm ...................................................................................................................................... 28
10.4.1 Motion.........................................................................................................................................................28
10.4.2 I/O Alarm:....................................................................................................................................................28
10.4.3 Lens Blocking..............................................................................................................................................29
10.5 Device..................................................................................................................................... 30
10.5.1 HDD (Where included)................................................................................................................................30
10.5.2 Audio...........................................................................................................................................................30
10.5.3 Logs............................................................................................................................................................31
10.6 System.................................................................................................................................... 32
10.6.1 General .......................................................................................................................................................32
10.6.2 User Configuration ......................................................................................................................................33
10.6.3 Info..............................................................................................................................................................33
10.7 Advanced................................................................................................................................ 34
10.7.1 System Update ...........................................................................................................................................34
10.7.1 Load Default ...............................................................................................................................................34
10.7.2 System Maintenance...................................................................................................................................34
10.8 Intelligent ................................................................................................................................ 35
10.8.1 Schedule.....................................................................................................................................................35
10.8.2 Detection.....................................................................................................................................................35
ENGLISH

DS1099-014A 3
10.8.2.1 Perimeter Intrusion Detection (PID)..........................................................................................................36
10.8.2.2 Line Crossing Detection (LCD).................................................................................................................36
10.8.2.3 Stationary Object Detection (SOD)...........................................................................................................36
11 Mobile Software ...................................................................................................................................... 37
11.1 Smartphone Device ................................................................................................................ 37
11.1.1 Urmet IUVS plus Mobile Software...............................................................................................................37
11.1.1.1 Live..........................................................................................................................................................38
11.1.1.2 Playback..................................................................................................................................................41
11.1.1.3 Record.....................................................................................................................................................42
11.1.1.4 Images.....................................................................................................................................................42
11.1.1.5 Remote Settings ......................................................................................................................................43
11.1.1.6 Alarm .......................................................................................................................................................43
11.1.1.7 Device......................................................................................................................................................44
11.1.1.8 Help .........................................................................................................................................................45
11.2 P2P function ........................................................................................................................... 46
12 Technical Specifications for the 2Mpx Fixed Lens Bullet and Dome IP cameras ........................... 48
13 Technical Specifications for the 2Mpx Varifocal Bullet and Dome IP cameras............................... 50
14 Technical Specifications for 2Mpx Direct Focus Motorised Lens Bullet and Dome IP cameras... 52
15 Maximum Recording Time with SD Card ............................................................................................. 54
15.1 Ref. 1099/202 – Ref. 1099/203 – Ref. 1099/303 – Ref. 1099/304......................................... 54
16 Appendix ................................................................................................................................................. 56
16.1 Router Port Forwarding .......................................................................................................... 56
16.2 Frequently Asked Questions .................................................................................................. 57

DS1099-014A 4
1 INTRODUCTION
Thank you for purchasing our integrated and developed network camera products for network video monitoring. Our range
includes the following products: Storage Network Bullet, Wireless Storage Network Bullet, IR Network Dome, IR Network
Weather-Proof and High-Speed Network Ball cameras. Individual high-performance SOC chips are used in the media
processor for audio/video capture, compression and transmission/transfer. An h.265 standard encryption algorithm
ensures clear and smooth video representation, as well as a high transfer capacity. The integrated Web server offers
users access to real-time surveillance and remote control of the front-end camera through the Internet Explorer browser.
The network cameras are easy to install and operate. They are ideal for large and medium-sized companies,
governmental projects, large malls, supermarket chains, intelligent buildings, hotels, hospitals, schools and other public
places, as well as for applications that requiring remote network video transmission and monitoring.
Instructions:
For the purpose of this manual, IP camera refers to a network camera.
The default factory IP address for the IP camera is 192.168.1.168.
The default factory administrator username for the IP camera is admin (in lowercase) and the password is admin (in
lowercase).
The default Web port number is 80 and the default client port number is 9988.
Statement:
Some information contained in this manual may differ from the actual product. For any problems that cannot be solved
with the help of this manual, please contact our technical support or an authorised dealer. This manual may be subject to
change without prior notice.

DS1099-014A 5
2 PRODUCT DESCRIPTION
URMET S.p.A. Ref. 1099/200, Ref. 1099/201, Ref. 1099/202, Ref. 1099/203, Ref. 1099/300 and Ref. 1099/301, Ref.
1099/302, Ref. 1099/303 and Ref. 1099/304 are 2 MegaPixel IP cameras that can be controlled by TCP/IP network
connections.
2.1 TECHNICAL CHARACTERISTICS
High-performance Hisilicon media processor with advanced functions.
CMOS progressive sensor.
Optimised H.265 video compression algorithms; multi-stream transmission ensures high definition images on
both narrowband and wideband.
Support simultaneous connection of up to 10 video streams (if the IP camera is connected to the NVR, the NVR
will occupy 3 streams, leaving 7 free video streams. If IP camera is connected to the Browser only, 10 streams
will be available).
SD Card support up to 128GB (for camera models with varifocal and motorized lenses).
The integrated Web Server allows multi-browser use (Internet Explorer, Firefox Mozilla up to version 5.1 and
Safari 6.0 for MAC O.S.) for real-time on-site monitoring, setup and management.
Managed through Urmet UVS client software.
Mobile software for the following platforms: iOS (Iphone and iPad), Android (smartphones and tablets).
Remote system firmware updates.
Support LAN and Internet.
Support ONVIF and RSSP protocols.
Support multiple network protocols, such as TCP/IP, UDP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP,
RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6 and Bonjour.
Support motion detection alarm function (the user can set the area and sensitivity) and sensor/alarm out function
(for camera models with motorised lenses and box cameras).
Support privacy zone function.
POE (optical) power supply function.
Support snapshot. Image upload via FTP or E-mail.
Log Support: System logs, network logs, parameter logs, alarm logs, user logs, recording logs, storage logs and
all logs.
Intelligent video analysis function (Perimeter intrusion detection, line crossing detection, stationary object
detection, etc.).
Reset Button supported (where included).
Support automatic download recovery function. Automatic connection in the event of network interruption.
Note: The specifications of the different products may vary slightly.
2.2 OPENING THE BOX
Check that the packaging and the contents are not visibly damaged. Contact the retailer immediately if parts are either
missing or damaged. Do not attempt to use the device in this case. Send the product back in its original packaging if
damaged.
ACCESSORIES PROVIDED
1 IP camera unit
1 installation bag
1 Quick Guide and 1 Appendix containing instructions for proper installation
1 Mini-CD containing Urmet Software

DS1099-014A 6


IMPORTANT NOTE:
Accessories may be changed without prior notice.
2.3 WARNINGS
Power supply
Before connecting the equipment to the electrical outlet, ensure that the nameplate specifications match
those of the mains power supply.
It is advisable to install a suitable disconnection and protection switch upstream from the equipment.
In the event of failure or malfunction, disconnect the power supply at the main switch.
Use only the power supply unit provided with the product.
Safety precautions
Keep the device away from rain and humidity to prevent the risk of fire and electrocution. Do not introduce
any material (solid or liquid) inside it. If this should accidentally occur, disconnect the device from the mains
and have it inspected by qualified personnel.
Never open the device. In all cases, contact qualified personnel or an authorised service centre for repairs.
Keep the device away from children, to prevent accidental damage.
Do not touch the device with wet hands to prevent electrical shock or mechanical damage.
Do not use the device if it falls or if the external casing is damaged. Continued use of the device in such
conditions could cause an electric shock. Contact the retailer or authorised installer.
Installation precautions
Do not install the camera in places exposed to rain or humidity. In these situations, use the special cases.
Avoid pointing the camera directly towards sunlight or other intense sources of light, even when switched
off; the subject to be filmed should not be against the light.
Avoid pointing the camera towards reflecting objects.
The presence of certain types of light (e.g. coloured fluorescent light) can distort the colours.
Do not position this device on an unstable surface, such as a tottering or slanted table. The device could
fall, causing injury or mechanical failures.
Stop using the device if water or some other material penetrates inside it, to prevent risk of fire or
electrocution. In such cases, contact the retailer or authorised installer.
Do not cover the device with a cloth while it is running to prevent deformation of the external casing and
overheating of internal parts, causing risk of fire, electrocution and mechanical failure.
Keep magnets and magnetised objects away from the device to prevent faults.
Do not use the device in the presence of smoke, vapour, humidity, dust or intense vibrations.
Do not operate the device immediately after moving it from a cold place to a warm place and vice versa.
Wait on average for three hours: this will allow it to adapt to the new environment (temperature, humidity,
etc.).
Precautions for use
Check that the device is not damaged after removing it from the packaging.
Ensure that the working environment is not too humid and that the temperature is within the indicated range.
Avoid pointing the camera towards sunlight to prevent damage to the sensor.
Cleaning the device
Rub gently with a dry cloth to remove dust and dirt.
Dip the cloth in neutral detergent if dirt cannot be removed with a dry cloth alone.
Do not use spray products to clean the device. Do not clean the device using volatile liquids (such a petrol,
alcohol, solvents, etc.) or chemically treated cloths to prevent deformation, deterioration or scratches to the
paint finish.
Disconnect the device from the electrical outlet before any cleaning or maintenance operations.
Recording images
This device is not designed as a burglar system but mainly to transmit and record video images. Urmet
S.p.A. cannot be held liable for loss or damage due to theft from the user’s premises.
Make a test recording before using the device to ensure that is working correctly. Please note that Urmet
S.p.A. is not liable for any loss of stored data or damage caused by incorrect installation, improper use or
malfunctioning of the device.
This device contains precision electronic components. Protect the device from bumps and jolts to ensure
proper recording of images.
Privacy and Copyright
The IP camera is designed for CCTV systems. The recording of images is subject to the laws in force in
the country of use. Recording of images protected by copyright is forbidden.
Product users are responsible for checking and complying with all local rules and regulations regarding
monitoring and the recording of video signals. The manufacturer SHALL NOT BE LIABLE for any use of
this product that is not in compliance with the laws currently in force. For more information see
http://www.garanteprivacy.it.
Firmware upgrade
You are advised to refer periodically to URMET S.p.A. Customer Service Technical Assistance to check
the availability of firmware updates.

DS1099-014A 7
Network configuration
The camera default setting is DHCP mode. If the installation network does not support dynamic
addressing (DHCP), the device will automatically switch to the factory-set IP address 192.168.1.168. The
Urmet “Device Search Tool” software can be used to change the IP address and other network settings to
prevent conflict with other devices on the network.
Once the camera is properly connected and configured on the IP network, its video and settings can be
viewed from a PC or smartphone.
Network connections
When connecting a remote PC (using client software or a browser), it should be borne in mind that any
video channel used on the PC will have a “unicast” connection (TCP, RTP, UDP).
The device can support up to 10 “unicast” connections, thus the video stream can be viewed from a
maximum of 10 remote devices (PC or smartphone) at the same time, depending on the available
bandwidth.

DS1099-014A 8
3 OVERVIEW
3.1 RANGE OF APPLICATION
These network cameras with their powerful image processing capacity can be used in various public places, such as
malls, supermarkets, schools, factories and workshops, as well as in environments requiring HD images, such as banks
and traffic control systems, as illustrated in the figure below:
3.2 PRODUCT DESCRIPTION
An IP camera is an online digital surveillance camera, equipped with a web server and capable of independent operation,
providing the user with access to real-time monitoring from any location through a web browser or client software.
These IP cameras feature the most advanced HiSilicon solution: an integrated media processing platform for audio/video
capture, compression and network transmission on a single board. It is compliant with High Profile H.264/ H265 coding
standards. Remote users can have access to real-time monitoring by entering the IP address or domain name of the IP
camera in the web browser. This network camera solution is suitable for residential or business environments, as well as a
wide range of situations that require remote network video monitoring and transmission. The IP cameras are easy to install
and operate.
The cameras can be controlled by several users with different levels of authorisation.
The IP cameras allow mobile detection and sending of e-mails and snapshots in cases of emergency; if an SD card is
included, the image or video snapshots can be stored in the card for subsequent retrieval.
Monitoring centre

DS1099-014A 9
3.3 OPERATING ENVIRONMENT
Operating system: Windows 7/Windows 8/Windows 2008 (32/64-bit), Windows 2003/Windows XP/Windows 2000 (32-bit)
CPU: Intel Core Duo II processor or higher
Memory: 1G or more
Video memory: 256M or more
Display: 1024 × 768 or higher resolution
Internet Explorer 6.0 or later

DS1099-014A 10
4 DEVICE CONNECTION
The IP camera can be connected in two ways:
•Connection to a PC
Connect the IP camera to the PC using a direct network cable, with the power input connected to a 12VDC
adaptor, and enter the IP addresses of the PC and the camera in a network segment. The IP camera will
communicate with the PC within one minute after being switched on if the network is working properly.
•Connection to a router/switch
This solution is more commonly used to connect the IP camera to the Internet; in this case, the camera and the PC
are connected to the LAN ports of a router/switch and the gateway of the camera is set to the IP address of the
router.
4.1 IP CAMERA CONNECTOR LAYOUT (WHERE PRESENT)
1. BNC Interface: Local video signal output.
2. Audio Output Interface: RCA female head (white), can connect with external devices, such as speakers.
3. Audio Input Interface: RCA female head (red), can connect with input devices, such as a microphone.
4. RJ45 Interface (Network Interface): Connector for a RJ45 network cable.
5. Power Interface: DC 12V.
6. Reset Button: The device will restore the default settings if this button is pressed and held for 3 seconds.
7. Alarm Interface: Including alarm input and output interface.
③,④are alarms input, ①is alarm output, ②is used as GND for Ref. 1099/304
①,②are alarms input, ③is alarm output, ④is used as GND for Ref. 1099/202, Ref. 1099/203, Ref.
1099/303.

DS1099-014A 11
5 OPERATING INSTRUCTIONS
5.1 CHECK CONNECTION
•The factory default IP address for the IP camera is 192.168.1.168 and the subnet mask is 255.255.255.0. Give your
computer an IP address in the same network segment as the IP camera, for example, 192.168.1.69, and the same
subnet mask as that of the IP camera.
•Check whether the IP camera is connected and switches on properly by selecting Start > Run, entering “cmd” and
pressing ENTER; then enter “ping 192.168.1.168” in the command line window.
•Check whether the IP camera is accessible. If the PING command is executed successfully, it means that the IP
camera is operating normally and the network is connected properly. If the PING command fails, check the IP
address and gateway settings of the PC, as well as the network connection.
5.2 SEARCHING FOR THE DEVICE
•Feedback: The Device Config Tool function may be used to search for the device across network segments. Before
running the Device Config Tool, select the local connection icon at the bottom right corner of the desktop;
•Add the IP addresses of several network segments in the TCP/IP local area connection settings (as shown below).
You can run this tool to search for any device with an IP address in the same network segment.
Note:
Device Config Tool uses the Multicast protocol to search for the device across the segments; however, since firewalls
prevent multicast data packet traffic, they must be disabled so that the information on the device can be acquired.

DS1099-014A 12
Online device search procedure
1. Run Device Config Tool by double-clicking on the icon.
It will search for and display any online device and its IP address, port number, web port number, number of
channels, configured name, device type and version, subnet mask, gateway, MAC address, connection pattern and
status.
5.3 INSTALLATION OF CONTROLS AND LOGIN TO THE SYSTEM
Before using the IE (Internet Explorer) browser to access the IP camera for the first time, the plug-in components must first
be installed, as follows:
Access the IP address of the IP camera to automatically download the controls from it.
Select an option in the plug-in installation pop-up dialogue box to run the installation process.
IPC Plug-In for the 2MP Series

DS1099-014A 13
6 LOGIN
6.1 PREVIEW
Open IE and enter the IP address of the camera (http://192.168.1.168) to bring up the login window shown below:
Login Interface for H.265 IP Cameras
Figure 1
In the login window you can choose a language for the IE client. Enter your username (admin by default) and password
(admin by default) and then press OK.
7 LIVE
Some of the buttons in the preview frame are described below.
: Button for setting the colour, brightness, contrast, saturation and sharpness of the frame.
: (PTZ control)
: This reads the recording file from the SD card and plays it back through the browser (if SD card support is
provided).

DS1099-014A 14
: Access to the device settings menu to customise the settings of various parameters.
: For snapshot, video file type and storage path settings.
: Help information (current user, Web browser and plug-in versions) and logout button for returning to the
login page.
: Stop/Start Live video.
: Preview frame ratio adjustment, toggling between Original Ratio, Automatic Ratio and Full Screen.
: Preview control buttons - Open Video, Snap, Zoom-In/Out, Sound On/Off,
Microphone (from left to right).
: Dynamic switching of the bit stream for the preview frame.
7.1 PTZ CONTROL
: (PTZ control) select the icon to open the following window:
On Autofocus cameras with AF optics, the PTZ interface will be as follows:

DS1099-014A 15
Eight different angles can be selected on the circular control,
•PTZ Speed: 0 – 10 indicates different PTZ speeds,
•ZOOM zooms in and out
•FOCUS increases or decreases FOCUS
•Restore: resets default settings
On Auto Focus cameras with DF optics, the PTZ interface will be as follows:
Option Value Explanation
Zoom Step/-/+ Manually adjusts zoom (+ zoom in / - zoom out)
Step: defines zooming speed
Focus Step/-/+ Manually adjusts focus (+ increase / - decrease)
Step: defines focusing speed
AF MODE SEMI ÷AUTO ÷
MANUAL ÷OFF
This function is used to customise the camera focusing
mode. Possible options are:
SEMI: focusing is performed only after the zooming
operations are finished.
AUTO: focusing is adjusted automatically.
MANUAL: focusing is adjusted manually.
OFF: focusing and zoom are deactivated. Activate this
option after having adjusted focus and zoom as required.
ONE SHOT AF / Function not available.
TDN AF ON ÷OFF This function, when activate, allows automatic focus
adjustment at each day->night or night->day switch.
LENS INIT /
This re-initialises the optics and obtained optical
calibration. To be performed when the camera is installed
for the first time and in case of movements with
consequent change of the framed picture.
IMPORTANT: do not use with AF MODE equal to OFF.
POWER MODE SAVE POSI ÷OFF
÷WIDE
This is used to adjust the zoom whenever the camera is
switched back on.
SAVE POSI: this holds the zoom position set before the
camera was switched off.
OFF: do not save the settings stored before switch-off.
WIDE: the camera is switched on in Wide mode.
AutoFocus / Adjusts focus automatically
Restore / Resets PTZ interface default settings (including focus)
Refresh / Updates the PTZ interface with changes to parameters
(including focus)

DS1099-014A 16
8 LOCAL SETTINGS
Select Local Settings to access the following dialogue window: here you can set the video storage location, paths for
downloading remote files and storing snapshot images, the file type (RF by default, with H265, AVI, MP4 or BMP
encoding), video recording duration and screen capture file type (BMP or JPG).

DS1099-014A 17
9 PLAYBACK
Select Playback in Record File, select the corresponding date, then Search to go to the page shown below.
Explanation of the button functions:
Type of recording file: ALL, Normal, IO, Intelligent.
Normal: 24H recording
(IO) alarms: Motion and Alarms.
Intelligent: see the chapter on intelligent video analysis.
：from left to right, Play/Pause, Stop, Advance one frame,
(select once to play one frame), Record, Capture, Download, Zoom, Audio control.
：from left to right, Zoom, Original proportions, Increase scale, Full screen.

DS1099-014A 18
10 REMOTE SETTING
10.1 DISPLAY CONFIGURATION
10.1.1 LIVE
Select Remote Settings to open the page shown below (default preview settings page):
Name: name of the IP camera.
Flicker control: choose 50Hz or 60Hz.
Transparency: choose the display transparency of the channel name and time on the preview frame (the lower the value,
the greater the transparency).
Show Name: the camera name is displayed.
Show Time: the date and time are displayed.
OSD: the red text on the frame; the channel name and time display can be repositioned by dragging them in the preview
frame.

DS1099-014A 19
10.1.2 IMAGE CONTROL
Select Image Control in Display to open the following page:
IR-CUT Mode: GPIO Automatic, Colour and Black and White.
IR-CUT Delay: IR-cut switching delay.
Lens Flip: On/Off.
Angle Flip: On/Off.
Corridor Mode: On/Off.
Angle Rotation: 0° or 180°.
Black Light: On/Off.
3D Noise Reduction: Off, Automatic, Manual.
Level: from 0 to 255.
WDR: On/Off.
AGC: OFF, Low, Medium, High.
White Balance: Automatic, Manual, Internal.
Shutter: Automatic, Manual.
Defog Mode: Off, Automatic, Manual.

DS1099-014A 20
10.1.1 PRIVACY ZONE
Select Privacy Zone in Display Configuration to open the following page:
Enable Privacy Zone, and then use the right mouse button to trace rectangles around areas not to be displayed during recording,
in screenshots and in Live viewing.
Save when done to keep the settings.
10.1.2 ROI
Select Display to open the following page:
ROI setting procedure:
1. Choose a region of application.
2. Press and hold the left mouse button and drag out a ROI (only one ROI can be set for each zone),
3. Select Save to apply the ROI.
Region ID: Up to 8 ROI zones can be set in one bit stream.
Enable Region: Enable or disable the ROI.
ROI level: Select a bit stream for the ROI from worst (), worse (), bad (), normal (), better () and best ().