UTEPO UTP1-SW2402TS-POE User manual

Please follow installation steps as below:
Please check the following items before installation, if it is missing, please contact the dealer.
24 Ports PoE Switch 1pcs
AC Power Cable 1pcs
1pcs
User Manual 1pcs
Accessories
1
2
4
5
) Turn off the power of all the related devices before the installation; otherwise the device would be
damaged;
)
)
)
)
Use Ethernet cable connect PoE IP camera and 1~24 downlink ports of product respectively;
3 Use an Ethernet cable to connect equipment uplink port with NVR or computer;
Connect power adapter;
Check if the installation is correct, equipment is in good condition, the connection is stable, then
power on for system.
Installation steps
Feature
24 Ports PoE Switch
User Manual
12
The 24 ports PoE switch is an unmanaged PoE Ethernet switch along with 24 * 100Base-TX
downlink PoE ports and 2 * 1000Base-TX uplink Ethernet ports featuring 30-watt 802.3at
PoE+ as well as 1 additional Gigabit Combo port. The total PoE power budget is up to 270
watts. It supports real-time PoE output LED display.The device can be widely used in video
security monitoring systems, network projects, etc.
Provide 24x 100Mbps downlink PoE Ethernet ports, 2x gigabit uplink Ethernet ports and
1x gigabit Fiber port;
Downlink Ethernet ports support PoE+, each port supports max. 30W output;
Support power consumption indication(LED indicates power output status);
Accord with IEEE802.3、IEEE802.3u、IEEE802.3ab、IEEE802.3 af/at standard;
4K MAC address,2.75Mb cache;
Quick installation, easy operation, convenient for wall-mounted、desktop and rack
installations.
Notice
The transmission distance depends on the signal source and cable quality; standard Cat5e/6 Ethernet
cable is strongly suggested for reaching the maximum transmission distance!
Notice
24 ports PoE Switch
VerB 1.0
1) Device must be connected with lightning protection grounding; otherwise protection level will be greatly
reduced; please use above No.20 wire to connect the grounding terminal;
2) The device requires rebooting after the dial switch has been utilized.
Front board
背面板
Back board
Board diagram
Cat5/5e/6
LCD display
NVR
switch
24 Ports PoE Switch
Fiber
PoE camera
PoE camera
PoE camera
PoE camera
CCTV Mode
PoE Output
Percentage LED PoE Output Ports
Uplink Gigabit
SFP Combo Port
Uplink
Gigabit Ports
PoE Output
LED
AC100~240V
Grounding Terminal
Application

连接接口
Specification 连接接口
34
Product specifications subject to change without prior notice.
连接接口
Trouble shooting
If any trouble in installation, please follow these steps:
Please make sure you have followed the instruction to install the device;
Please confirm if the RJ45 cable order is in accordance with the EIA/TIA568A or 568B industry
standards;
The power supply of each PoE port is no more than 30W; please do not connect the PoE device which
exceeds the maximum PoE power supply;
Please replace a failure device with a proper one to check if the device is broken.
RJ 45 Making Method
Pin Color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
Pin Color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 568A EIA/TIA 568B
Notice
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should conform with
EIA/TIA568A or 568B.
1) Shuck off about 2cm long the insulating layer, and bare the 4 pairs UTP cable;
2) Depart the 4 pairs UTP cable and straighten them;
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
4) Cut out 1.5 cm cable wrap and leave the bare wire;
) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
5
6) Then use wire crimper to crimp it;
7) Follow the 5 steps above to make the another end, following the same sequence of the first plug;
8) Using network tester to test the cable whether is working.
24 ports PoE Switch
24 ports PoE Switch
Item
Description
Product Type
Product Type
24ports
Port
Description
Downlink Ethernet Ports
24×10/100Base-TX PoE+
Uplink Ethernet Ports
2 10/100/1000Base-T+1 1000Base-X(combo)× ×
Power Input
1×AC Female Terminal
Grounding Terminal
1×Grounding Terminal
PoE&Power
Power Input
Mains on load,100～240VAC 50/60Hz
PoE Power Supply
End-span(1/2，3/6),IEEE802.3 af/at
PoE Max. Power Output
270W
Single Port Power Output&
Voltage
Single Port PoE Power Output≤30W, Voltage 54VDC
One-key CCTV
CCTV Mode
1. Downlink ports only communicate with uplink ports;
2. Restrain network storm under 2Mbps;
3.Extend transmission distance to 250m;
4.Rate:10Mbps(Downlink Ports)
Network
Parameters
Network Standard
IEEE 802.3,IEEE 802.3u,IEEE 802.3 ab, IEEE 802.3z
Transmission Distance
100m(Max.)
Exchange Capacity
8.8Gbps
Packet Transfer Rate
6.55Mpps
MAC Address
4K
Packet Data Cache
2.75Mb
Indicators
Status
Power Input
1x Red LED
Downlink Ethernet Ports
Link:24x Green LED
PoE:24x Yellow LED
Uplink Ethernet Port Link
2x Green LED
PoE Power Output Percent
5x LED(Including 3x Green, 1x Yellow, 1x Red), separately indicate
30%、60%、9～100% 0%、95%
Protection
Level
ESD
/ - -6KV 8KV, Per:IEC61000 4 2
Surge Protection
6KV, Per:IEC61000-4-5
Operation
Environment
Operation Temperature
- ℃～ ℃10 45
Storage Temperature
- ℃40 85℃～
Humidity(Non-condensing)
0～95%
Mechanics
Dimensions(LxWxH)
442 *285 *44.5mm mm mm
Material
Iron
Color
Black