UTEPO UTP3-GSW1604TS-P200 User manual

1
2
16-Port/24-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
User Manual
Packing List
Open the box of the product and carefully unpack it. The box shouldcontain the following items. Please
check before installation, if any missing, please contact your dealer immediately.
Items
Quantity
Switch
1 pc
AC Power Cable
1 pc
Mounting Accessory
1 set
Quick Installation Guide
1 pc
Product Introduction
This series products are 16-Port/24-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper
Ethernet Switch.
This series switches provide 16/24 Gigabit Ethernet RJ-45 downlink ports, 2 Gigabit Ethernet RJ-45
uplink ports and 2 Gigabit SFP uplink ports. All RJ-45 downlink ports support Power-over-Ethernet
(PoE+) and deliver up to 30W power per port.
The switches support working in three modes: default, VLAN, and flow control. It can be widely used in
video security monitoring systems, network projects, etc.
This series contains two types:
16-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
(Short for 16-Port PoE Switch)
24-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
(Short for 24-Port PoE Switch)
Hardware Introduction
The two types are of the same dimensions. Here takes 24-Port PoE Switch as example
Dimensions (mm)
16-Port/24-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
Front Panel (16-Port PoE Switch)
Front Panel (24-Port PoE Switch)
Rear Panel (16-Port/24-Port PoE Switch)
Led Indicators
Indicators
Status
Descriptions
Power
Power Supply Indicator
On
The main power supply is working.
Off
The main power supply is off.
Link
Port Link Indicator
On
The port is linking normally.
Blink
The port is transmitting or receiving data.
Off
The port links down.
PoE
Port PoE Indicator
On
The port is supplying PoE normally.
Off
The port stops supplying PoE.
DIP Switch
Status
Descriptions
Default
Default mode. All ports are free to communicate.
VLAN
Downlink ports are isolated from each other, but can communicate with uplink ports.
Flow control
Enable flow control function. This mode is suitable for video surveillance transmission.
Note:
After changing the working mode, please power on the device again to enter the corresponding mode.

16-Port/24-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
16-Port/24-Port Gigabit PoE + 2-Port Gigabit SFP + 2-Port Gigabit Copper Ethernet Switch
3
4
Installation Steps
1) Before installation, please disconnect the power supply of each signal source and equipment. Live
installation may damage the transmission equipment.
2) The switch supports 19-inch rack, desktop and wall-mounted installations. Users can install the
switch in a rack, or place it on a clean, stable, grounded workbench, or on the vertical, stable wall.
The 19-inch rack installation steps are shown in the following table:
Step 1: Fix the hangers on the side of the switch.
Accessories
2*
8*
Step 2: Install the switch on the rack with screws in the package.
Accessories
4*
Step 3: Continue to install other devices in the rack. The distance
between the devices should be more than 5cm.
Accessories
N/A
3) After step 2) is completed, please use Cat5 or better cables to connect the switch and the device.
4) Check the installation and the wiring, after confirming that the connection is correct and reliable,
power on the switch.
The installation is complete.
CAUTION
Power on the system only after confirming that the wiring is correct, to avoid damage to the
equipment.
For better transmission performance, it is recommended to use Cat5 or better cables to connect
the switch and powered devices.
For better protection performance, it is recommended always to make the ground connection first
and disconnect it at the end when operating the unit.
Each PoE RJ-45 port can provide a maximum power of 30W for a powered device. Please do not
connect to a powered device with a power exceeding 30W.
Before operating or maintaining the switch, please read the user manual carefully to avoid
equipment damage caused by misoperation.
Specifications
Items
UTP3-GSW1604TS-P200
UTP3-GSW2404TS-P420
Ethernet Ports
Downlink Ports
16*10/100/1000 Base-T PoE RJ-45 (Auto-
MDI/MDI-X)
24*10/100/1000Base-T PoE RJ-45
(Auto-MDI/MDI-X)
Uplink Ports
2*10/100/1000 Base-T RJ-45, 2*1000 Base-X SFP(Mini-GBIC)
PoE
PoE Standard
IEEE 802.3af/at( PSE)
PoE Power Supply Type
End-span
PoE Pin Assignment
1/2(+), 3/6(-)
PoE Power Output
53.5V DC
54.5V DC
PoE Power
30W max for each port, 175W max
30W max for each port, 390W max
Switch Property
Standards
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3X
Forwarding Modes
Store and Forward
Packet Buffer
4Mbyte
MAC Table
8k
Switching Capacity
40Gbps / non-blocking
56Gbps / non-blocking
Packet Forwarding Rate
29.8Mpps
41.7Mpps
Power Supply
Input Voltage
100V~240V AC, 50/60Hz
Power Consumption
200W (Including PoE)
420W (Including PoE)
Reliability
Surge Immunity
6kV, Standard: IEC6000-4-5
ESD
6 kV Contact Discharge, 8kV Air Discharge, standard: IEC61000-4-2
Operating Temperature
-10 ~50
Storage Temperature
-40 ~85
Operating Humidity
5%~95% (Non-condensation)
Physical Parameters
Led Indicators
1*PWR Indicator
16*Downlink Port Link Indicators
16*Downlink Port PoE Indicators
4*Uplink Port Link Indicators
1*PWR Indicator
24*Downlink Port Link Indicators
24*Downlink Port PoE Indicators
4*Uplink Port Link Indicators
Dimension(W*D*H)
442mm*285mm*44mm
Gross Weight
5000g 60g
5350g 60g
Net Weight
3800g 40g
4150g 50g
Material
Metal shell
Installation
Rack mounted /desktop/wall mounted
Certifications
Certifications
CE, FCC
Version,V2.0, updated 2020.12.17.
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.