Quick Installation Guide Quick Installation Guide
Indicator
The port is supplying PoE properly.
The port stops supplying PoE.
SFP port is linking normally.
SFP port is transmitting or receiving data.
SFP port is linking down.
DIP Switch
Default:All ports are free to communicate, transmission distance: 0~100m.
VLAN mode: downlink ports are isolated from each other, but can communicate with uplink ports. This
mode supports PoE watchdog.
CCTV mode: the transmission distance is extended up to 250m, but the rate is limited to 10Mbps. This
mode supports PoE watchdog.
PoE Mode DIP Switch
8-Port FE PoE++ 2-Port Gigabit Ethernet Switch PoE mode can be set by DIP switch.
Mode1: 45W max for each port.
Mode2: 90W max for port 1, disabled PoE function for port 2, 45W max for ports 3 to 8 each.
1) Before installation, power off the equipment. Installation when device is powered on is prohibited.
2) The switch supports desktop and wall-mounted installations. Users can place it on a clean, stable,
grounded workbench, or install it on the vertical, stable wall.
3) Connect the switch and other equipment using Cat5 or better Ethernet cable.
4) Check the installation and the wiring, after confirming that the connection is correct and reliable, power on
the switch.
The installation is completed.
Power on the system only after confirming that the wiring is correct, to avoid damage to the equipment. It
is recommended to use the power adapter and power cable in the package to connect the power supply.
For better transmission performance, it is recommended to use Cat5 or better Ethernet cable to connect
the switch and powered devices.
For better protection performance, it is recommended to always make the ground connection first and
disconnect it at the end when operating the device.
Before operating or maintaining the switch, please read the user manual carefully to avoid equipment
damage caused by misoperation.
4-Port FE PoE+ 2-Port
Fast Ethernet Switch
4-Port FE PoE++ 2-Port
Fast Ethernet Switch
8-Port FE PoE++ 2-Port Gigabit
Ethernet Switch
4*10/100BASE-T PoE RJ-45(Auto-MDI/MDI-X)
8*10/100BASE-T PoE RJ-45(Auto-
MDI/MDI-X)
2*10/100BASE-T RJ-45(Auto-MDI/MDI-X)
2*10/100/1000BASE-T RJ-45(Auto-
MDI/MDI-X)
Default: All ports are free to communicate, transmission distance: 0~100m.
VLAN mode: downlink ports are isolated from each other, but can communicate with uplink ports. This
mode supports PoE watchdog.
CCTV mode: the transmission distance is extended up to 250m, but the rate is limited to 10Mbps. This
mode supports PoE watchdog.
Mode1: 45W max for each port
Mode2: 90W max for port 1, disabled
PoE function for port 2, 45W max for
ports 3 to 8 each.
≤130W (Full load including PoE)
≤160W (Full load including PoE)
IEEE 802.3, IEEE 802.3u, IEEE 802.3x
1 port: 1/2(-), 3/6(+)
2~4 ports:1/2(+), 3/6(-)
1 port: 3/6/4/5(+),1/2/7/8(-)
2~4 ports:1/2(+), 3/6(-)
1 port: 3/6/4/5(+),1/2/7/8(-)
2~8 ports:1/2(+), 3/6(-)
30W max for ports 1 to 4
each
120W max for whole
switch
90W max for port 1, 45W
max for ports 2 to 4 each
120W max for whole
switch
Mode1: 45W max for each port.
Mode2: 90W max for port 1, disabled
PoE function for port 2, 45W max for
ports 3 to 8 each
150W max for whole switch
IEC61000-4-2, Level 3: Contact Discharge: ±6kV, Air Discharge: ±8kV
IEC61000-4-5, line to earth: 6kV
-10°C~55°C, 5%~95% (Non-condensation)
-40°C~70°C, 5%~95% (Non-condensation)
Version: V1.2, updated 2023-10-17.
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
