Utilitech FZ-8A User manual

Français p. 10
Español p. 20
TOWER FAN
28 IN
OSCILLATING
ITEM #0809479
MODEL A#FZ-8
Serial Number Purchase Date
ATTACH YOUR RECEIPT HERE
1
PH18683
Questions, problems, missing parts? Before returning to
your retailer, call our customer service department at
1-866-994-4148, 8 a.m. - 8 p.m., EST, Monday- Sunday.

DESCRIPTION QUANTITY
Front Base 1
Rear Base 1
Power Cord 1
Fan Housing 1
1
Oscillation Button 1
PART
A
B
C
D
E
F
2
PACKAGE CONTENTS
Rotary Knob Switch
EEE
BBF
D
C
A
BB
B

SAFETY INFORMATION
Please read and understand this entire manual before attempting
to assemble, operate or install the product.
3

PLEASE READ AND SAVE THESE IMPORTANT SAFETY
INSTRUCTIONS
POLARIZED PLUG
POWER CORD SAFETY TIPS
4
override

PLUG AND POWER CORD INSTRUCTIONS
5
(not included)

1.
center of the base assembly.
Feed the power cord (C) through the
2.
6
ASSEMBLY INSTRUCTIONS
Before beginning assembly of product, make sure all parts are
present. Compare parts with package contents list. If any part is
missing or damaged, do not attempt to assemble the product.
No Tools Required for Assembly.
Estimated Assembly Time: 5-10 minutes
C
Align the two portions of circular
base and insert the four connectors
of the rear base Binto the four
slots of the front base A．Please
ensure four buckles are connected
closely and the two parts are tightly
secured．There should be aclick”
sound when the buckles are properly
connected ．
( )
( )
“
(Fig. 1)
1Buckles Connectors
ABB
B

3.
Note: Do not operate the tower fan unless it is in its proper,
upright position.
7
4.
OPERATING INSTRUCTIONS
Once fan is fully assembled (see Assembly Instructions section), place
fan on a dry, level surface. Plug it into a 120V AC electrical outlet.
Controlling the Fan Speed
To operate, turn the rotary knob switch to the appropriate speed
control option. There are four available settings: 0=Off, ,3=High
4
Align the groove and arrow at the
bottom of the fan housing D to the
arrow on the base assembly which is
near the central hole edge of the base
assembly
Please make sure the three
buckles at the bottom of the fan body
connected closely to the base and all
connections between the fan body and
the base are tight and secure
( )
(
) (Fig. 3). Push the base
assembly into the fan body until a “click”
is heard.
(Fig. 4).
Locate the power cord holding bracket
at the bottom of the base assembly．
Gently pull any slack out of the power
cord，place the power cord securely in
the holding bracket and secure the
power cord bracket over the power
cord．Then thread the power cord
through the U” locating notch on the
edge of the base assembly
“
(Fig. 5).
Stand the fan in an upright position.
2=Medium, .1=Low
5

8
Controlling Fan Oscillation
CARE AND MAINTENANCE
TO STORE: Make sure to disassemble and clean the fan before
storing. Retain the original packaging for the purpose of storing
your fan. Always store fan in a dry place. Never store it while it is
still plugged in. Never wrap the cord tightly around the fan, and do
not put any stress on the cord where it enters the fan, as it could
cause the cord to fray and break.
CAUTION: DO NOT ALLOW WATER TO RUN INTO THE INTERIOR
OF THE FAN AS THIS COULD CREATE A FIRE OR ELECTRIC
SHOCK HAZARD. THE FAN MOTOR IS FACTORY LUBRICATED
FOR LIFE AND WILL REQUIRE NO FURTHER LUBRICATION.
NO OTHER USER MAINTENANCE IS REQUIRED OR
RECOMMENDED. IF SERVICE IS REQUIRED, SEND YOUR FAN
TO THE AUTHORIZED SERVICE FACILITY.
TO CLEAN: Always disconnect the power cord from the electrical
outlet when cleaning your fan. Light accumulated dust can be
removed by using a soft cloth to wipe away the dust at the back
grille of the fan. Wipe the exterior surfaces of the fan occasionally
with a damp cloth (not dripping wet) and dry thoroughly with a soft
dry cloth before operating the fan. Do not use harsh cleaners or
materials to clean this unit. Doing so will damage the unit.
To activate or de fan oscillation, press the oscillationactivate button.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants to the original purchaser that each new
product and service part is free from defects in material and
workmanship and agrees to repair or replace under this warranty any
defective product or part as follows from the original date of purchase
for a period of one (1) year.

THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER:
1. Products sold damaged or incomplete, sold “as is”, sold
reconditioned
or used as rental equipment.
2. Delivery, installation or normal adjustments explained in the owner’s
manual.
3. Damage or liability caused by shipping, improper handling,
improper
installation,
incorrect voltage or improper wiring, improper
maintenance, improper modification, or the use of
accessories and/or
attachments not specifically recommended
by the manufacturer.
4. Repairs necessary because of operator abuse or negligence, or the
failure to install, operate,
maintain and store the product according to
the instructions in the owner’s manual.
5. Damage caused by cold, heat, rain, excessive humidity, corrosive
environments and materials, or other contaminants.
6. Expendable items that become worn during normal use.
7. Freight costs from customer to vendor.
8. Repair and transportation costs of products or parts determined not
to be defective.
9. Any incidental, indirect or consequential loss, damage, or
expense
that may result from any defect, failure or malfunction
of the product.
Some states do not allow the exclusion or
limitation of consequential
damages so the above exclusions or
limitations may not apply to you.
Some states do not allow the exclusion or limitations on how long
an implied warranty lasts, so the above limitations may not apply to
you. You may have other rights which vary from state to state.
9
Printed in China
Our customer service number: 1-866-994-4148, 8 a.m. - 8 p.m.,
EST, Monday-Sunday.

ARTICLE #0809479
MODÈLE A#FZ-8
Numéro de série Date d’achat
10
VENTILATEUR
TOUR
OSCILLANT
DE 71,12 CM
JOIGNEZ VOTRE REÇU ICI
20
dimanche.