Specifications are subject to change without notice.
© 2016 VTech Communications, Inc. All rights reserved.
12/16. VM3251_QSG_V1.
Document order number: 96-011463-010-100
Basic operation - Parent unit
Adjust speaker volume
Press +
/
VOL
/
-to adjust your parent unit speaker
volume. It determines the volume of sound
transmitted from your baby units.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold TALK and speak to your parent unit.
Your voice is transmitted to the baby unit.
Turn off the screen
Press LCD ON/OFF to switch off the screen.You can
still hear sound from the selected baby unit.
Use the menu
Press MENU to enter the menu, choose a menu item,
or save a setting.
While in the menu:
Press or to scroll among the menu options.
Press to enter the desired sub- menu.
Press or to select an an item.
Press SELECT to confirm your selection.
•
•
•
Turn off the parent unit
Press and hold to power off your parent unit.
Basic operation - Baby unit
Night vision
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When
the baby unit detects low light levels, the infrared
LEDs turn on automatically.The images from this
baby unit is in black and white, andunit is in black and white, and appears
on screen.
It is normal if you see a shor t white gla re on your
parent unit screen as th e baby unit is ad apting to th e
dark environment.
When the i nfrared LEDs are on, t he image i s in
black an d white. This is nor mal due to ex ternal l ight
source s.
Depending on the surroundings and other
interfering factors, like lightings, objects, colors and
backgrounds, the display resolution may vary. Adjust
the baby unit’s angle, or place the baby unit at a
higher level to prevent glare and blurry display.
•
•
•
Adjust speaker volume
Press +
/
VOLUME
/
-to adjust your baby unit
speaker volume. It determines the lullaby
volume and talkback volume transmitted from
your parent unit.
Turn off the baby unit
Slide the ON/OFF switch to OFF to power off
your baby unit.
> More than 1
meter (3 feet)
63℉
Long press
Press VIEW to switch between the image of baby units and .
Change different views (require additional baby unit - VM3211)
Press PATROL to alternately view the image from baby units and every 10 seconds.
Pre s s CAM .10s
You can view from different baby units if you have more than one baby units in your system (VM3211, purchased separately).
2s
Insert the screws into the
holes and tighten the screws
until only 1/4 inch of the
screws are exposed.
If you drill the holes into a stud,
go to step 3.
-OR-
If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with
the wall.
Mount the baby monitor (optional)
OR
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the
wall (7/32 inch drill bit).
Check for reception strength and
camera angle before drilling the holes.
•
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed.You
can tighten the other screw in the
top hole.
Place the baby unit on the wall
mount bracket.Tighten the screw
into the threaded socket at the
bottom to secure the baby unit.
Place the baby unit on the wall mount
bracket.Tighten the screw into the threaded
socket at the bottom to secure the baby
unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
