V-tech Accessory Handset for use with the CS6319 CS6329 or... User manual

User’s manual
Accessory handset for
use with VTech models
CS6328-2/CS6328-3/
CS6328-4/CS6328-5/
CS6319/CS6319-2/
CS6319-3/CS6319-4/
CS6329/CS6329-2/
CS6329-3/CS6329-4/
CS6329-5
Model: CS6309

Congratulations
on purchasing your new VTech product. Before using this
telephone, please read the Important safety instructions on
page 9 of this manual.
This manual has all the feature operations and troubleshooting
necessary to install and operate your new VTech telephone.
Please review this manual thoroughly to ensure proper
installation and operation of this innovative and feature rich
VTech product. For support, shopping, and everything new at
VTech, visit our website at www.vtechphones.com. In Canada,
please visit www.vtechcanada.com.
The ENERGY STAR®program (www.energystar.
gov) recognizes and encourages the use of
products that save energy and help protect our
environment. We are proud to mark this product
with the ENERGY STAR®label indicating it meets
the latest energy efciency guidelines.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Telephones identied with this logo have reduced
noise and interference when used with most T-coil
equipped hearing aids and cochlear implants. The
TIA-1083 Compliant Logo is a trademark of the
Telecommunications Industry Association. Used
under license.

Table of contents
i
Getting started .............................. 1
Parts checklist................................. 1
Battery installation .......................... 2
Battery charging.............................. 3
Add and register a handset............. 4
Replace a handset .......................... 5
Handset layout ................................ 6
Appendix........................................ 8
Battery............................................. 8
Important safety instructions........... 9
Precautions for users of
implanted cardiac pacemakers.. 10
Operating range ............................ 10
Maintenance.................................. 11
About cordless telephones............ 12
The RBRC®seal............................ 13
Warranty........................................ 14
FCC, ACTA and IC regulations ..... 16
Technical specications ................ 18

Parts checklist
Your telephone contains the following items. Save your sales
receipt and original packaging in the event warranty service
is necessary.
User’s manual
Handset
Charger and power adapter
Battery Battery
compartment cover
Getting started
To purchase replacement batteries or power adapters,
visit our website at www.vtechphones.com or call
1 [phone]. In Canada, go to www.vtechcanada.com
or dial 1 [phone].
1

CHARGE
light
Battery installation
Install the battery as shown below.
If the battery compartment cover is on the handset,
press on the indentation and slide the cover to remove.
Plug the battery connector securely into the socket
inside the handset battery compartment, matching the
color-coded label.
Place the battery with the label THIS SIDE UP facing up
and the wires inside the battery compartment.
Align the cover at against the battery compartment,
then slide it towards the center of the handset until it clicks
into place.
Charge the handset by placing it in the telephone base or
charger. The CHARGE light is on when the handset charges.
1.
2.
3.
4.
5.
13
2
45
If the handset will not be used for a long time, disconnect
and remove the battery to prevent possible leakage.
To purchase replacement batteries, visit our website at
www.vtechphones.com or call 1 [phone]. In
Canada, go to www.vtechcanada.com or dial
1 [phone].
•
•
Getting started
2

Battery charging
Once you have installed the battery, the screen indicates the
battery status (see the table below). If necessary, place the
handset in the telephone base or charger to charge the
battery. For best performance, keep the handset in the
telephone base or charger when not in use. The battery is fully
charged after 16 hours of continuous charging. See the table
on page 8 for battery operating times.
If the screen is blank, you need to charge the handset without
interruption for at least 10 minutes to give the handset enough
charge to use the telephone for a short time. When the battery
is low, the handset beeps four times every minute, shows
LOW BATTERY and a ashing icon. If you are on a call
in low battery mode, the handset has four short beeps to
alert you.
The following table summarizes the battery charge indicators
and actions to take.
Battery indicators Battery status Action
The screen is blank. Battery has no
charge and the
handset cannot be
used.
Charge without
interruption (at least
10 minutes).
The screen shows
PLACE IN CHARGER
and ashes.
Battery has very
little charge and
the handset cannot
be used.
Charge without
interruption (at least
four minutes).
The screen shows
LOW BATTERY and
ashes. The handset
beeps four times every
minute.
Battery has enough
charge to be used
for a short time.
Charge without
interruption until
the screen shows
HANDSET X (about
30 minutes).
The screen shows
HANDSET X.
Battery is charged. To keep the battery
charged, place it in
the telephone base
or charger when not
in use.
If you do not plug in the battery into the handset and place it in the
telephone base or charger, the screen displays NO BATTERY.
Getting started
3

Add and register a handset
Each newly purchased handset (CS6309) must be registered
to the telephone base before use. When rst purchased,
each handset shows 1.PRESS FIND HS ON BASE 4 SEC
and 2.THEN PRESS # ON HANDSET alternately. You
may need to charge the handset before registering to the
telephone base. For more details on battery charging, see
page 3.
To make registration easier, read all the instructions on this
page before you begin.
To register a handset:
Place the unregistered handset in the
telephone base. If 1. PRESS FIND HS
ON BASE 4 SEC and 2.THEN PRESS #
ON HANDSET do not appear alternately
on the handset screen after a few
seconds, remove the handset and place it
in the telephone base or charger again.
On the telephone base, press and hold
/FIND HANDSET for about four seconds
(until the red IN USE light on the
telephone base turns on) and then
release the button.
Remove the handset from the telephone
base or charger. Press # and the handset
displays REGISTERING...PLEASE WAIT. It takes about
10 seconds to complete the registration. The handset
shows HANDSET REGISTERED and you hear a beep
when the registration completes.
When the registration is complete, the newly registered
handset is assigned the next available handset registration
number. For instance, if you already have HANDSET 1, the
next registered handset will be HANDSET 2.
1.
2.
3.
If the registration fails, the handset shows 1.PRESS FIND
HS ON BASE 4 SEC and 2.THEN PRESS # ON HANDSET
alternately. To reset the handset, remove the handset from
the telephone base and place it back in. Try the registration
process again.
You cannot register a handset if any other system handset
is in use.
Only one handset set can be registered at a time.
•
•
•
Getting started
4

Replace a handset
If you want to replace a handset or re-assign the designated
handset number of a registered handset, you must deregister
all the handsets and then individually register each handset.
To make deregistration easier, read all of the instructions on
this page before you begin.
To deregister all handsets:
Press and hold /FIND HANDSET on the telephone
base for about 10 seconds (until the IN USE light on the
telephone base turns on and starts to ash), then release
/FIND HANDSET.
Press and release /FIND HANDSET again. You must
press /FIND HANDSET while the IN USE light is still
ashing. The IN USE light ashes for approximately
seven seconds.
The deregistration process takes about 10 seconds to
complete. All handsets show 1.PRESS FIND HS ON BASE
4 SEC and 2.THEN PRESS # ON HANDSET alternately
when the deregistration completes.
If deregistration fails, you may need to reset the telephone and
try again.
To reset:
Pick up the registered handset and then press /FLASH.
Press OFF/CLEAR and place the handset back in the
telephone base.
-OR-
Unplug the power from the telephone base, then plug it
back in.
1.
2.
3.
1.
2.
1.
You cannot deregister a handset if any system handset is
in use.
Getting started
5

Handset layout
CHARGE light
On when the handset is charging in
the telephone base or charger.
1
While reviewing a call log entry, press
repeatedly to add or remove 1in
front of the telephone number before
dialing or saving it in the directory.
/FLASH
Press to make or answer a call.
During a call, press to answer an
incoming call when you receive a call
waiting alert.
REDIAL/PAUSE
Press to review the redial list.
While dialing or entering numbers
into the directory, press and hold to
insert a dialing pause.
(speakerphone)
Press to make or answer a call.
During a call, press to switch
between speakerphone and handset.
TONE
While you have set the dial mode
to pulse and on a call, press to
temporarily change to tone dial mode.
VOL/CID (volume/caller ID)
Press to review the call log when the
telephone is not in use.
While in a menu, press to scroll down.
During a call, press to decrease the
listening volume.
6
Getting started

Getting started
Handset layout
VOL/ (volume/directory)
Press to enter the directory when the
telephone is not in use.
While in a menu, press to scroll up.
During a call, press to increase the
listening volume.
MENU/SELECT
Press to show the menu.
While in a menu, press to select an
item, or save an entry or setting.
OFF/CLEAR
During a call, press to hang up.
While the handset is ringing, press to
silence the ringer temporarily.
While the telephone is not in use,
press and hold to erase the missed
calls indicator.
During programming, press to exit
without making changes.
#
Press repeatedly to show other
dialing options when reviewing a call
log entry.
MUTE/REMOVE
While on a call, press to mute the
microphone.
While reviewing the call log, directory
or redial list, press to delete an
individual entry.
Press to delete digits when predialing.
INT (intercom)
Press to start an intercom
conversation or transfer a call.
7