V-tech Digiart Creative Easel Assembly Instructions

Parent’s Guide
91-003216-021 UK

C
M
Y
CM
MY
CY
CMY
K
Grow with VTech(105x148)bw1P-V2.pdf 1 08/18/2014 9:35:53

3
INTRODUCTION
Thank you for purchasing the VTech®DigiArt Creative Easel.
The DigiArt Creative Easel transforms into a whiteboard, blackboard
or drawing table. Using the magic pen, children can follow the ashing
lights to draw more than 150 letters, numbers, objects and shapes.
They can also explore their creativity and draw anything they’d like.
INCLUDED IN THIS PACKAGE
• One DigiArt Creative Easel (assembly required)
• Three pieces of chalk
• One parent’s guide
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy and should be discarded for your child’s safety.
NOTE: Please keep this parent’s guide as it contains important
information.
ACTIVATING NORMAL PLAY
1. Press the ON/OFF button to turn the unit on.
2. Press the FREE DRAW BUTTON.
3. Place and hold the MAGIC PEN on an LED dot for 2 seconds.

4
Creative Easel
20 21 22 16
18
17
9
10
12
14
2
3
7
8
6
5
4
1
13
19
15
5MAGIC PEN
2WHITEBOARD
6SUPPLIES TRAY
3LED SCREEN AREA
7BLACKBOARD
4MAGIC PEN HOLDER
8BATTERY COMPARTMENT
9ON/OFF BUTTON
10 LETTER BUTTONS
11 NUMBER BUTTON
12 VOLUME DOWN BUTTON
13 VOLUME UP BUTTON
14 MUSIC ON/OFF BUTTON
15 BRIGHTNESS BUTTON
16 DRAW OBJECTS BUTTON
17 DRAW SHAPES BUTTON
18 GUESS THE PICTURE BUTTON
19 FREE DRAW BUTTON
20 LEFT ARROW BUTTON
21 OK BUTTON
22 RIGHT ARROW BUTTON
1PAPER CLIP
11

5
Supplies Tray (B)
Easel Hooks
Table Hooks
Hook
(one on each side)
Latch Buttons
Buckle Handles
Buckles
Bars
Legs (C)
PARTS OF
THE DIGIART CREATIVE EASEL
Blackboard/Whiteboard (A)
A
B
C

6
ASSEMBLY INSTRUCTIONS
Adult assembly required. For your child’s safety, do not let your
child play with the toy until it is fully assembled.
WHITEBOARD EASEL FORM
Step 1:
To attach the Supplies Tray (B) to the Blackboard/Whiteboard (A).
• Remove the two black plastic covers protecting the two bars on (A1).
• Turn both (A) and (B) upside down and align them horizontally.
• Snap the hooks on (B) to the bars on (A1).
• After hooked, rotate (B) to make it perpendicular to (A).

7
Step 2:
Lift the wider part of A2 of the Blackboard/Whiteboard (A). Then
unsnap the narrow area of part A2 and move it towards the Supplies
Tray (B). Insert the narrow part of A2 into the slot on the back of the
Supplies Tray (B).
Step 3:
Attach the latches of the Supplies Tray (B) to both Easel Hooks of
A2, then push the latch handles inward to tighten them.
Step 4:
Insert two Legs into part A2 of the Blackboard/Whiteboard (A) and
two Legs into the bottom of the Supplies Tray (B). The Legs will lock
into place.

8
Step 5:
Turn the DigiArt Creative Easel upright and assembly is complete.
Note: To disassemble the easel for better storage, just reverse the
above steps.
To remove the legs from the easel, pull them out one by one in the
opposite direction of installing. You may need to apply force if the legs
are installed too tightly.

9
TRANSFORM FROM WHITEBOARD TO
BLACKBOARD
Step 1:
Make sure the Magic Pen is placed in the Magic Pen Holder.
Step 2:
Detach the Blackboard/Whiteboard (A) from the stand by pulling up,
turning it over to the blackboard side and putting it into the stand again.
To change the blackboard back into a whiteboard, reverse the order of
the steps above.

10
TRANSFORM FROM EASEL TO DRAWING TABLE
Step 1:
Make sure the unit is turned OFF and in Whiteboard mode before
transforming. Loosen the Buckles on both sides by pressing the Latch
Button and at the same time pulling the Buckle Handles outward.
Step 2:
Hold the Blackboard/Whiteboard (A) with one hand and with the
other hand, move the back legs slowly backward until the Blackboard/
Whiteboard (A) lies horizontally on the four Legs.