V-tech Drill & Learn Workbench User manual

Drill & Learn WorkbenchTM
Instruction Manual

2
2
2
INTRODUCTION
Thank you for purchasing the Drill & Learn Workbench™.
Let’s build! Get ready for role-play fun with the included
workbench, working toy drill, hammer, wrench, sander, saw
and screws. It’s time to tackle the to-do list!
Circular Saw
Drill Press
Sander
5 Tool
Buttons Gears
Power Tool Zone
3 Power Tools
Ruler Mode
Selector
Off/Low/
High Volume
Selector

3
3
3
INCLUDED IN THE PACKAGE
• 1 Workbench top • 1 Electronic panel • 1 Back panel
• 1 Back panel top • 2 Panel supports • 4 Legs
• 2 Trays • 1 Left leg support • 1 Right leg support
• 1 Center tray • 1 Circular saw top • 1 Circular saw base

4
4
4
• 1 Sander base • 1 Sander top • 1 Drill press top
• 1 Drill press base • 1 Project Guide holder • 1 Clock
• 1 Drill • 1 Wrench • 1 Hammer
• 1 Walkie-Talkie • 1 Saw • 1 L-wrench

5
5
5
• 1 Vise • 1 Screwdriver • 1 Large gear
• 17 Building pieces • 4 Toy pegs & 4 Toy Wheels
• 10 Blue toy screws & nuts • 5 Toy bolts
For Workbench Assembly
• 19 Gray toy screws & nuts • 10 Real screws
Note:
The gray toy screws and toy nuts are for assembly.
The blue toy screws and toy nuts are play pieces.

6
6
6
• Project Guide
• Quick Start Guide
• 1 Label sheet

7
7
7
WARNING
All packing materials such as tape, plastic sheets,
packaging locks, removable tags, cable ties, cords and
packaging screws are not part of this toy, and should
be discarded for your child’s safety.
NOTE
Please save this Instruction Manual as it contains
important information.
ATTENTION
Pour la sécurité de votre enfant, débarrassez-vous de
tous les produits d’emballage tels que rubans adhésifs,
feuilles de plastique, attaches, étiquettes, cordons et
vis d’emballage. Ils ne font pas partie du jouet.
NOTE
Il est conseillé de sauvegarder ce manuel d’utilisation
car il comporte des informations importantes.
Unlock the Packaging Locks
Rotate the packaging locks
counterclockwise 90 degrees.
Pull out the packaging locks and
discard.

8
8
8
CAUTION:
Adult assembly required. This package contains small
parts. For your child’s safety, do not let your child play
with the toy until it is fully assembled.
ATTENTION :
Ce jouet contient des petites vis. Il doit être assemblé
par un adulte. Pour la sécurité de votre enfant, ne pas
le laisser jouer avec tant qu’il n’est pas complètement
assemblé par un adulte.
CAUTION:
For your child’s safety, do not let your child stand or
sit on the table of the Workbench.
ATTENTION :
Pour la sécurité de votre enfant, ne laissez pas votre
enfant s’asseoir ou se tenir debout sur le plan de
travail de l’établi.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
ATTENTION :
Les piles ou accumulateurs doivent être installés par
un adulte. Tenir les piles ou accumulateurs hors de
portée des enfants.

9
9
9
BATTERY INSTRUCTIONS
Battery Removal and Installation
1. Make sure the unit is turned Off.
2. Find the battery cover located on the
back of the electronic panel, use a
screwdriver to loosen the screws, and
then open the battery cover.
3. Remove old batteries by pulling up on
one end of each battery.
4. Install 2 new AA (AM-3/LR6) batteries
following the diagram inside the
battery box. (For best performance,
alkaline batteries or fully charged
Ni-MH rechargeable batteries are
recommended.)
5. Replace the battery cover and tighten
the screws to secure.
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Only batteries of the same or equivalent type as
recommended are to be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
• Remove exhausted batteries from the toy.
• Dispose of batteries safely. Do not dispose of batteries
in fire.

10
10
10
RECHARGEABLE BATTERIES:
• Remove rechargeable batteries (if removable) from toy
before charging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Do not charge non-rechargeable batteries.
IMPORTANT : INFORMATIONS CONCERNANT
LES PILES
Les piles fournies avec le produit permettent de tester le jouet
en magasin mais ne sont pas des piles longue durée.
• Mettre en place les piles ou les accumulateurs en
respectant les polarités + et –.
• Ne pas mélanger des piles ou des accumulateurs neufs avec
des usagés.
• Ne pas mélanger différents types de piles : alcalines, zinc-
carbone et rechargeables.
• Seules des piles du type recommandé doivent être utilisées.
• Ne pas mettre les bornes d’une pile ou d’un accumulateur en
court-circuit (en reliant directement le + et le –).
• Retirer les piles ou les accumulateurs en cas de non-
utilisation prolongée.
• Enlever les piles ou les accumulateurs usagés du jouet.
• Ne les jeter ni au feu ni dans la nature.
PILES RECHARGEABLES :
• Enlever, lorsque c’est possible, les accumulateurs du jouet
pour les recharger.
• Les accumulateurs ne doivent être chargés que sous la
surveillance d’un adulte.
• Ne pas tenter de recharger des piles non rechargeables.

11
11
11
LABEL APPLICATION
Please securely stick the labels to the toy as indicated
below:

12
12
12

13
13
13
WORKBENCH ASSEMBLY INSTRUCTIONS
Please refer to images on pages 3, 4 and 5.
1. Use the included L-Wrench to
screw a Gray Toy Nut to a Gray
Toy Screw. Repeat for all 19 Gray
Toy Nuts and Gray Toy Screws.
2. Use the included Drill or Screwdriver to tighten 8 Gray
Toy Screws and Nuts to attach the Right and Left Leg
Supports where the center tray will rest on the left and
right legs.
3. Insert the Center Tray into the
two Leg Supports. You will hear
the pieces snap together when
correctly inserted.

14
14
14
4. Insert the Large Gear into the Electronic Panel. Insert
the Electronic Panel into the slot of the Workbench Top.
Use four of the Real Screws and your own screwdriver
to securely attach the Electronic Panel.
5. Use four of the Real Screws and your own screwdriver
to securely attach the Vise.
6. To secure the base to the
legs, use the included Drill or
Screwdriver to tighten two of
the Gray Toy Screws to the
Workbench Top.

15
15
15
7. Use the remaining two Real Screws to attach the Project
Guide Holder to the Back Panel of the Workbench.
8. Use four of the Gray Toy
Screws and the included Drill
or Screwdriver to tighten the
Back Panel of the Workbench
to the Panel Supports.
9. Use two of the Gray Toy
Screws and the included Drill
or Screwdriver to tighten
the Back Panel Top of the
Workbench to the Panel
Supports.

16
16
16
10. Insert the Panel Supports
into the Workbench Top and
use two of the Gray Toy
Screws and the included Drill
or Screwdriver to tighten the
supports.
11. Clip the two Trays into the
slots to the left and right of
the Workbench Top.
12. Use a Gray Toy Screw and the
included Drill or Screwdriver to
attach the Clock to the Panel of
the Workbench.
13. Screw a Peg to the Panel of the
Workbench and hang the Wrench
or Hammer on the Peg, or insert
the Wrench or Hammer into a slot
on the Panel of the Workbench.

17
17
17
POWER TOOL ASSEMBLY INSTRUCTIONS
Circular Saw, Drill Press and Sander
1. Insert the Drill Press Top into
the Drill Press Base. You will hear
the pieces snap into place when
properly inserted.
2. Insert the Circular Saw Top into
the Circular Saw Base. You will
hear the pieces snap into place
when properly inserted.
3. Insert the Sander Top into the
Sander Base. You will hear the
pieces snap into place when
properly inserted.
NOTE: The tool tops and bases cannot be disassembled after
assembly.

18
18
18
Activating Normal Play Mode
The first time the Drill & Learn Workbench™ is used, you will
need to exit Try-Me mode and activate Normal Play mode.
1. Turn the unit On.
2. Place a Power Tool on the Power Tool Zone. You will hear
a sound indicating that the unit is in Normal Play mode.
Using the Power Tools
Drill Press
• Place the Drill Press in the Power
Tool Zone.
•Place a rectangular Building Piece
on the base of the Drill Press.
•Press down the Drill Press handle
to pretend to make straight holes.

19
19
19
Circular Saw
• Place the Circular Saw in the Power Tool Zone.
• Connect two rectangular Building Pieces together.
• Place the Building Piece on the Circular Saw base.
•Press down the gray handle of the Circular Saw to “cut”
the Building Piece into two parts.
Sander
• Place the Sander in the Power Tool Zone.
•Place a rectangular Building Piece on the peg of the
sander.
•Push the bar forward to pretend to make the block
smooth.

20
20
20
TO BEGIN PLAY
Move the Off/Low/High Volume Selector to Low or High to
turn on the unit, then move the Mode Selector to select a
game to play.
PRODUCT FEATURES
1. Off/Low/High Volume Switch
To turn the unit On or adjust the
volume, slide the Off /Low /
High Volume Selector to Low
or High volume. To turn the unit
Off, slide the selector to Off.
2. Mode Selector
Slide the Mode Selector to choose
from three different activities.
3. Power Tools
Place Circular Saw, Drill Press or
Sander in the Power Tool Zone to
learn about colors, tools facts and
fun sound effects. Listen to sing-
along songs or answer the activity
questions.