V-tech GO! GO! CORY CARSON Cory's Stay & Play Home... Assembly Instructions

Parent’s Guide
91-003865-006 US
Cory’s Stay & Play Home™

2
2
2
2
INTRODUCTION
Thank you for purchasing the Go! Go! Cory Carson®Cory’s Stay &
Play Home™!
Get ready to play at Cory’s house. Check out Cory’s cool bedroom,
zoom down the ramp and watch DJ Train Trax in the living room. Place
mini characters on the PlayZone™ to hear character phrases and
sound effects.
Clock Button
Bath Button
TV Button
PlayZoneTM Location
SmartPoint®Location
Mini Cory
Mini Mama Mini Chrissy

3
3
3
3
INCLUDED IN THIS PACKAGE
NOTE: This toy is not intended for teething.
One mini Cory
One chair
One bathtub wall
One mini Chrissy
One playmat
One first floor base
One mini Mama
One arch
One bath roller
One door Two columns
One corner pillar

4
4
4
4
One lampOne house topOne bed
One second floor hallwayOne main floor wall
One second floor base One nightstand One clock & tent
One TV stand coverOne TV stand One refrigerator
One refrigerator door

5
5
5
5
- One label sheet
- One parent’s guide
One ramp
One fireplace wall One connector One window
One pole

6
6
6
6
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy, and should be discarded for your child’s safety.
NOTE:
Please keep this parent’s guide as it contains important information.
ATTENTION :
Pour la sécurité de votre enfant, débarrassez-vous de tous les produits
d’emballage tels que rubans adhésifs, feuilles de plastique, attaches,
étiquettes et vis d’emballage. Ils ne font pas partie du jouet.
NOTE :
Il est conseillé de conserver ce guide des parents car il comporte des
informations importantes.
GETTING STARTED
Battery Removal and Installation
Cory’s Stay & Play Home™
1. Make sure the unit is turned Off.
2. Locate the battery cover underneath
the second floor of the house. Use
a coin or a screwdriver to loosen
the screw.
3. Remove old batteries by pulling up
on one end of each battery.
4. Install 3 new AAA (AM-4/LR03) batteries following the diagram
inside the battery box.
5. Replace the battery cover and tighten the screw to secure the
battery cover.

7
7
7
7
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Removerechargeablebatteriesfromthetoybeforecharging
(if removable).
• Rechargeablebatteriesareonlytobechargedunder
adult supervision.

8
8
8
8
LABEL APPLICATION
Please apply the labels to the playset as show below:
1
2
4
3
7
11
15
12
14
6
5
13
16
18
20
19
17
22
21
8
10
27
9
5
6
21
22
4
27
37
12
11
14
15
13
2
1
8
9
10
17 19
16
18
20

9
9
9
9
ASSEMBLY INSTRUCTIONS
With the Cory’s Stay & Play Home™, safety comes first.To ensure
your child’s safety, adult assembly is required.
1. Place the Door into the Arch and press into place.
2. Lay the First Floor Base face up on a flat surface. Insert the two
Arch posts into the first floor. Press down until you hear a click.
3. Insert the two Columns into the First Floor Base.

10
10
10
10
4. Insert the Corner Pillar into the First Floor Base. Press down
until you hear a click.
5. Press the Roller into the Bathtub Wall until you hear a click.
6. Insert the Bathtub Wall into the Second Floor Base behind the
tub. Press down until it clicks into place.
7. Insert the Nightstand into the Second Floor Base. Press down
until you hear a click.