V-tech Play & Chase Puppy Assembly Instructions

91-004015-001 UK
Parent's Guide
Play & Chase Puppy

3
INTRODUCTION
Thank you for purchasing the Play & Chase Puppy.
Follow this cute puppy for three ways to play! Explore numbers
and counting with sit-down play, then get up and dance with this
interactive friend! Keep the giggles going with a game of follow
the leader!
Hand Button
Light Up
Heart Button
Light Up Number Button Light Up Music Button
On/Off/
Mode Switch

4
INCLUDED IN THE PACKAGE
• Play & Chase Puppy
• Parent’s Guide
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part
of this toy, and should be discarded for your child’s safety.
NOTE
Please save this parent’s guide as it contains important information.
NOTE
Please cut and discard the plastic strap that attaches the
Play & Chase Puppy to the box. The strap is not part of this toy
and should be discarded for your child’s safety.
Removing the Packaging Locks
Rotate the packaging locks anticlockwise
90 degrees.
Pull out the packaging locks and discard.
GETTING STARTED
Battery Removal and Installation
1. Make sure the unit is turned Off.
2. Find the two battery covers located on the bottom of the unit, use a
screwdriver to loosen the screws and then open the battery covers.
3. Remove old batteries by pulling up on
one end of each battery.
4. Install 4 new AA batteries following the
diagram inside the battery boxes. (For
best performance, alkaline batteries
or fully charged Ni-MH rechargeable
batteries are recommended).
5. Replace the battery covers and tighten
the screws to secure.

5
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Only batteries of the same or equivalent type as recommended
are to be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
• Remove exhausted batteries from the toy.
• Dispose of batteries safely. Do not dispose of batteries in re.
RECHARGEABLE BATTERIES:
• Remove rechargeable batteries from the toy before charging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Do not charge non-rechargeable batteries.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specied
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in the Batteries and Accumulators Regulation.

6
PRODUCT FEATURES
1. On/Off/Mode Switch
To turn the unit On, slide the
On/Off/Mode Switch to the Learning
mode or the Follow mode
position. You will hear a song, playful
phrases and sounds. To turn the unit
Off, slide the On/Off/Mode Switch to
the Off position.
2. Automatic Shut-Off
To preserve battery life, the Play & Chase Puppy will
automatically shut off after approximately 50 seconds
without input, or when the front and back sensors have been
continuously activated for 10 minutes without other inputs. The
unit can be turned on again by pressing any button, or by sliding
the On/Off/Mode Switch.
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product
or batteries responsibly.
VTech®cares for the planet.
Care for the environment and give your toy a second life by
disposing of it at a small electricals collection point so all its
materials can be recycled.
In the UK:
Visit www.recyclenow.com to see a list of collection points near you.
In Australia & New Zealand:
Check with you local council for kerbside collections.

7
NOTE
This product is in Try-Me mode in the packaging. After opening the
package, please remove the demo tag from the bottom of the unit.
Then, turn the Play & Chase Puppy off and on again to proceed with
normal play. If the unit powers down or if the light fades out during
play, please install a new set of batteries.
ACTIVITIES
1. Light Up Buttons
Press the Light Up Buttons to learn
numbers, counting, feelings and
motions, as well as hearing sing-
along songs and music. The puppy
will dance and move in response to
the voice and sound responses if it is
on the oor. The lights will ash with
the sounds.
2. Hand Button
Give puppy a high ve by pressing
the Hand Button, as well as hearing
playful phrases and music. The lights
will ash with the sounds.
3. Front and Back Sensors
The puppy is equipped with special
sensors on the front and back of the
hoverboard. Approach the sensors
to activate them and see the puppy
ride away or rotate and respond with
playful phrases, music and sounds.
The lights will ash with the sounds.

8
NOTE
The infrared light sensors in the hoverboard are sensitive to sunlight.
The sensors may not perform properly in brightly lit, sunny rooms or
under direct sunlight.
4. Pick-Up Sensor
The puppy has a special sensor on
the bottom of the hoverboard, so the
puppy knows when it has been picked
up. Each time you pick up the puppy,
you will hear a cute phrase. The
puppy’s heart button will ash with
the sounds.
MELODY LIST
1. A-Tisket, A-Tasket
2. Bingo
3. The Entertainer
4. Glow Worm
5. Hey, Diddle Diddle
6. Skip to My Lou
7. One Man Went to Mow a Meadow
8. Hickory, Dickory, Dock
9. Aiken Drum
10. Bear Went Over the Mountain
11. Did You Ever See a Lassie?
12. Where Has My Little Dog Gone?
13. Old MacDonald
14. Humpty Dumpty
15. The Wheels on the Bus

9
SONG LYRICS
Song 1
Follow me. One, two, three.
I am moving really fast, can you catch me?
Song 2
Ride, ride, ride my board,
Turning round and round.
I like to move, I like to groove,
Every day and night.
Song 3
I hop on to my hoverboard and zoom around the ground.
I wiggle my body, I wag my ears and spin all around.
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2.
Keep the unit out of direct sunlight and away from any direct
heat sources.
3. Remove the batteries if the unit will not be in use for an extended
period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit
to moisture or water.
TROUBLESHOOTING
If for some reason the unit stops working or malfunctions, please
follow these steps:
1. Turn the unit Off.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit On. The unit should now be ready to use again.
5. If the unit still does not work, install a new set of batteries.
If the problem persists, please contact our Consumer Services
Department, and a service representative will be happy to help you.

10
CONSUMER SERVICES
Creating and developing VTech®products is accompanied by a
responsibility that we at VTech®take very seriously. We make every
effort to ensure the accuracy of the information, which forms the
value of our products. However, errors sometimes can occur. It is
important for you to know that we stand behind our products and
encourage you to call our Consumer Services Department with
any problems and/or suggestions that you might have. A service
representative will be happy to help you.
UK Customers:
Phone: [phone] (from UK) or [phone] (outside UK)
Website: www.vtech.co.uk/support
Australian Customers:
Phone: [phone]
Website: support.vtech.com.au
NZ Customers:
Phone: [phone]
Website: support.vtech.com.au
PRODUCT WARRANTY/
CONSUMER GUARANTEES
UK Customers:
Read our complete warranty policy online at vtech.co.uk/warranty.
Australian Customers:
VTECH ELECTRONICS (AUSTRALIA) PTY LIMITED –
CONSUMER GUARANTEES
Under the Australian Consumer Law, a number of consumer guarantees
apply to goods and services supplied by VTech Electronics (Australia)
Pty Limited. Please refer to vtech.com.au/consumerguarantees for
further information.