V-tech Go Go Smart Wheels Car User manual

© 2015 VTech
Printed in China
91-003062-000
User’s Manual
Ultimate RC SpeedwayTM

2
STUNT RAMP STARTING LINE
9 SMARTPOINT®
LOCATIONS
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels®
Ultimate RC SpeedwayTM!
Zip around the Go! Go! Smart Wheels®Ultimate RC SpeedwayTM,
and speed through the stunt ramp, up the motorized elevator and down
the straightaway with the RC SmartPoint®Racer! Then, make a pit
stop and pretend to make repairs.The speedway includes over 13 feet
of interchangeable tracks and features a stunt ramp, elevator, movable
gears, track switches and more. Get an additional Go! Go! Smart
Wheels®RC SmartPoint®Racer (sold separately) and race a friend!
Introduction
REMOTE
CONTROL
RC SMARTPOINT®
RACER
SMARTPOINT®
ELEVATOR
SMARTPOINT®
PIT STOP

3
INCLUDED IN THIS PACKAGE
Included In This Package
One podium wall One antenna One gas pump
One trophy
One podium
support
One SmartPoint®
podium base
One pit stop
SmartPoint®base
One remote
control
One pit stop
gear wall
One RC
SmartPoint®Racer
One stunt
ramp base
One stunt
ramp track
Two stunt ramp
supports
One user’s manual

4
Included In This Package
One 60-degree
track, male
One long SmartPoint
®
ramp track
One long
ramp support
One video screen
piece
One elevator
ramp track
One SmartPoint
®
elevator
One short
ramp track
Two switch
track bases
Two switch
track pieces
One flagOne small
track support
One short track
with base
One video screen
SmartPoint
®
straight track

5
One starting line
SmartPoint
®
track
One starting
line gate
Five 90-degree
tracks, female
Four 90-degree
tracks, male
One cross track One oil spill
SmartPoint
®
straight track
One SmartPoint
®
straight track
Two 3/4 straight
tracks
Three 1/4 straight
tracks, male
Eight 1/4 straight
tracks
Three label
sheets
Included In This Package

6
GETTING STARTED
BATTERY INSTALLATION – VEHICLE
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the back
of the race car. Use a screwdriver to
loosen the screw.
3. Install 3 new “AAA” (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended for
maximum performance.)
4. Replace the battery cover and tighten
the screw to secure.
Getting Started
WARNING:
All packing materials, such as tape, plastic sheets, packaging
locks and tags are not part of this toy, and should be discarded
for your child’s safety.
ATTENTION:
Pour la sécurité de votre enfant, débarrassez-vous de tous
les produits d’emballage tels que rubans adhésifs, feuilles de
plastique, attaches et étiquettes. Ils ne font pas partie du jouet.
NOTE:
Please keep this user’s manual as it contains important
information.
Unlock the packaging locks:
Turn the packaging lock counter-clockwise
several times.
Pull out and discard the packaging lock.

7
BATTERY INSTALLATION – REMOTE CONTROL
1. Locate the battery cover on the back of
the remote control. Use a screwdriver to
loosen the screw.
2. Install 2 new “AAA” (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new alkaline
batteries is recommended for maximum
performance.)
3. Replace the battery cover and tighten
the screw to secure.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
Battery Notice

8
Label Instructions
Please adhere the labels to the playset securely as
indicated on the following page:
1 1 2
345
667
8
9
10
11 12
12
13
14
15
14
14
14
14
3
2
16 17
18
19 19 19
20
21
22
23 23 23
24 25 26
27
27
27
27
25
25
25
24
24
24
24
28 29 29

9
Label Instructions
1
3
45
67
8
9
10
11
12
13
15
14
2
16
17
18
23
20
21 22
19
24 25
26
27
28
29

10
Assembly Instructions
ASSEMBLY INSTRUCTIONS
With the VTech®Go! Go! Smart Wheels®Ultimate RC
SpeedwayTM, safety comes first.To ensure your child’s safety, adult
assemblyisrequired.
1. Insert the starting line gate into the
slots on the starting line SmartPoint®
track as shown in the photo. You will
hear a “click” sound to indicate the
starting line gate is secure. Once
the starting line gate is connected to
the starting line SmartPoint®track,
it cannot be detached.
2. Insert the gas pump into the slot
on the pit stop SmartPoint®base
as shown here. You will hear a
“click” sound to indicate the gas
pump is secure. Once the gas
pump is connected to the pit stop
SmartPoint®base, it cannot be
detached.
3. Insert the pit stop wall into the pit
stop SmartPoint®base as shown
here. You will hear a “click” sound to
indicate the pit stop wall is secure.
Once the pit stop wall is connected
to the pit stop SmartPoint®base, it
cannot be detached.

11
4. Insert the antenna into the podium wall as shown. Then, insert
this assembled podium wall and the trophy into the slots on the
SmartPoint®podium base as shown.You will hear a “click” sound
to indicate the pieces are secure. Once these pieces are connected
to the SmartPoint®podium base, they cannot be detached.
5. Insert the podium support into the assembled SmartPoint®podium
base from step four. Next, attach this SmartPoint®podium base
with support to the pit stop wall. When the pieces are connected,
you will hear a “click” sound and they cannot be detached.
6. Insert the long SmartPoint®ramp
track onto the long ramp support as
shown here. Press firmly to make
sure it is connected securely.
Assembly Instructions

12
7. Insert the stunt ramp supports in the stunt ramp base slots as shown
below (each stunt ramp support has a notch at its base that fits
the slot it connects to). Then, fit the pegs on the side of the stunt
ramp track into the openings on the stunt ramp supports (pegs on
the side of the stunt ramp track are sized to fit their corresponding
stunt ramp support opening).
8. Insert the small support into the short track with base, then attach
the 60-degree male track to the small support. Next, insert the small
support into the stunt ramp base. You will hear a “click” sound to
indicate the small support is secure.
9. Insert the flag into the video screen piece as shown on the next
page. Then, insert the video screen piece into video screen
SmartPoint®straight track as shown on the next page.You will hear
a “click” sound to indicate the video screen piece is secure. Once
the video screen piece is attached to the video screen SmartPoint®
straight track, it cannot be detached.
Assembly Instructions

13
10. If the elevator track piece is at the base of the SmartPoint®elevator,
lift the elevator track piece up. Then, attach the elevator ramp
track to the SmartPoint®elevator as shown below. You will hear
a “click” sound to indicate the elevator ramp track is secure. Once
the elevator ramp track is attached to the SmartPoint®elevator, it
cannot be detached.
11. Insert the two switch track pieces into the two switch track bases
as shown below.You will hear a “click” sound to indicate the switch
track pieces are secure. Once the switch track pieces are attached
to the switch track bases, they cannot be detached.
Assembly Instructions

14
Once you’ve completed the above steps, you are ready to create your
race course! Using the included track pieces, you can configure the Go!
Go! Smart Wheels®Ultimate RC SpeedwayTM in different ways! You
can also connect these track pieces to other Go! Go! Smart Wheels®
and Go! Go! Smart Animals®playsets. (Each sold separately.) For
optimal performance, use the RC SmartPoint®Racer on the Go!
Go! Smart Wheels®Ultimate RC SpeedwayTM when in REMOTE
CONTROL MODE.
Assembly Instructions

15
PRODUCT FEATURES – RC
SMARTPOINT®RACER
1. OFF/MODE SELECTOR SWITCH – VEHICLE
To turn the unit ON, slide the OFF/
MODE SELECTOR SWITCH to
the REMOTE CONTROL MODE
( ) or STANDARD MODE
( ) position. To turn the unit OFF,
slide the OFF/MODE SELECTOR
SWITCH to the OFF ( ) position.
2. CHANNEL SELECTOR SWITCH
To allow the RC SmartPoint®Racer
and remote control to function
together, slide the CHANNEL
SELECTOR SWITCH to the same
location on the RC SmartPoint®
Racer and remote control.
Note: If two or three RC SmartPoint®Racers are operating in the same
vicinity, place each vehicle on a different channel. (A maximum of
three RC SmartPoint®Racers can operate in one location.)
3. FORWARD/BACKWARD BUTTONS
In REMOTE CONTROL MODE,
press the FORWARD BUTTON
or BACKWARD BUTTON on the
remote to make the race car go
forward or backward. (The effective
distance for the race car to recognize
the remote control is 9 ft. to 18 ft.The
distance will be shorter when the
batteries are low.)
Product Features – RC Smartpoint®Racer

16
NOTE: For optimal performance, only play with your RC SmartPoint®
Racer, in REMOTE CONTROL MODE, indoors and out of direct
sunlight.
For your child’s safety, only use the motorized car on Go! Go!
Smart Wheels®playsets. Do not roll the car on your clothing,
body or hair while the motorized car is turned on. Do not block
the path of the motorized car with any part of your body when
the RC race car is moving forward or backward. If something
gets caught in the car’s wheels while the motor is on, lift
the car up so it is no longer touching your child or slide the
mode selector switch to the off position to turn off the motor.
4. AUTOMATIC SHUT-OFF
To preserve battery life, the VTech®Go! Go! Smart Wheels®
RC SmartPoint®Racer will automatically power down after
approximately 60 seconds without input in STANDARD MODE
and 120 seconds in REMOTE CONTROL MODE. In STANDARD
MODE, the unit can be turned on again by pressing the LIGHT-UP
DRIVER BUTTON or pushing the vehicle. In REMOTE CONTROL
MODE, press the LIGHT-UP DRIVER BUTTON or turn the unit off
and on again to turn the unit on. (The remote control cannot wake
up the race car.)
Note: The RC SmartPoint®Racer is in try-me mode in the packaging.
After opening the package, turn the vehicle off and on again to proceed
with normal play.
Product Features – RC Smartpoint®Racer

17
Activities – RC Smartpoint®Racer
ACTIVITIES – RC SMARTPOINT®RACER
1. Slide the race car’s OFF/MODE
SELECTOR SWITCH to either
REMOTE CONTROL MODE or
STANDARD MODE to turn the
race car ON.You will hear a song, a
phrase and sounds. The LIGHT-UP
DRIVER BUTTON will flash with the
sounds.
2. Press the LIGHT-UP DRIVER
BUTTON to hear race car sounds,
songs and phrases. The LIGHT-UP
DRIVER BUTTON will flash with the
sounds.
3. When the race car is in STANDARD
MODE, push the race car to hear
fun sounds and melodies. While the
melody is playing, push the vehicle
again to add in fun sounds on top of
the melody.The LIGHT-UP DRIVER
BUTTON will flash with the sounds.
4. For remote control play, turn the race
car to REMOTE CONTROL MODE.
To drive the race car with the remote
control, ensure both the race car and
remote control are set to the same
channel number using the CHANNEL
SELECTOR SWITCHES. Once both
items are on the same channel,
press the FORWARD BUTTON
or BACKWARD BUTTON on the
remote for some racing fun!

18
Note: When the RC SmartPoint®Racer is in REMOTE CONTROL
MODE, do not push the vehicle forward or backward on surfaces. The
RC SmartPoint®Racer should only be pushed manually, forward and
backward, in STANDARD MODE.
5. Operate up to three vehicles at once by putting each on a different
channel number using the CHANNEL SELECTOR SWITCHES!
(Each RC SmartPoint®Racer sold separately.)
6. For added fun, the RC SmartPoint®
Racer interacts with the Go! Go!
Smart Wheels®Ultimate RC
SpeedwayTM and other Go! Go!
Smart Wheels®and Go! Go! Smart
Animals®playsets. Simply roll or
navigate the race car over one of
the playset’s SmartPoint® locations
to see the light flash and to hear
greetings, fun sounds, short tunes
and sing-along songs (each playset
sold separately).
NOTE: For optimal performance, use the RC SmartPoint®Racer
on the Go! Go! Smart Wheels®Ultimate RC SpeedwayTM when in
REMOTE CONTROL MODE.
Activities – RC Smartpoint®Racer

19
PRODUCT FEATURES – ULTIMATE RC
SPEEDWAYTM
1. SMARTPOINT®LOCATIONS
The Ultimate RC SpeedwayTM
features nine different SmartPoint®
locations that interact with the
included RC SmartPoint®Racer or
any other Go! Go! Smart Wheels®
SmartPoint®vehicle (each sold
separately). Simply drive, roll or place
the vehicle on any SmartPoint®
location to hear fun sounds, music
and phrases.
2. MECHANICAL PLAY PIECES
The Ultimate RC SpeedwayTM
features 6 different mechanical play
pieces that are triggered by the
included RC SmartPoint®Racer.
Simply press the FORWARD
BUTTON on the remote when the
RC SmartPoint®Racer is driving
over a mechanical piece and watch
the piece magically move.
Product Features – Ultimate RC SpeedwayTM