V-tech Go!Go! Smart Wheels Tow & Go Garage Assembly Instructions

Parent’s Guide
Tow & Go Garage™
91-003497-000

2
2
2
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels®Tow
& Go Garage™!
Park, learn and play with the Go! Go! Smart Wheels®Tow & Go
Garage™. This interactive garage features two floors of pretend play
and learning fun! Place Trent the Tow Truck on the elevator and watch
him spin when raised up to the second level platform. Then, push Trent
to watch him race under the helipad, down the spiral ramp and arrive
at the car wash platform!
Repair
Platform
Elevator
9SmartPoint®
Locations
SmartPoint®
To w Tr u c k Car Wash

3
3
3
INCLUDED IN THIS PACKAGE
One base
One SmartPoint®
To w Tr u c k
One second level
platform
One elevator
support
One elevator gate One center
support
One pillar
support
One elevator wall
One elevator
bracket
One car wash
platform
NOTE: This toy is not intended for teething.
One car
wash gate
One elevator
platform
One car
wash brush

4
4
4
One gate
arm
One platform
track
One label sheet
Two gears One second
level sign
One ticket booth
Two helipad
supports
One helipad
platform
Ramp track BRamp track AOne ramp track
support
One repair
platform
- One parent’s guide
One gate base

5
5
5
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy, and should be discarded for your child’s safety.
NOTE: Please keep this parent’s guide as it contains important
information.
ATTENTION:
Pour la sécurité de votre enfant, débarrassez-vous de tous les produits
d’emballage tels que rubans adhésifs, feuilles de plastique, attaches,
étiquettes et vis d’emballage. Ils ne font pas partie du jouet.
NOTE: Il est conseillé de conserver ce guide des parents car il comporte
des informations importantes.
Adult assembly required.
Ce jouet doit être assemblé par un adulte.
Unlock the packaging locks:
Turn the packaging lock counter-
clockwise several times.
Pull out and discard the packaging lock.

6
6
6
GETTING STARTED
BATTERY INSTALLATION
Tow Truck
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom
of the Tow Truck. Use a screwdriver to
loosen the screw.
3. Install 2 new AAA (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended
for maximum performance.)
4. Replace the battery cover and tighten
the screw to secure the battery cover.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.

7
7
7
LABEL APPLICATION
Please adhere the labels to the playset securely as
indicated on the following pages:
22
5
2
1
1
6
34

8
8
8
23
16 18
17
7
8
9
28 29 25
26
19
10
27
12
13 13
13
15
13
14
24
11

9
9
9
ASSEMBLY INSTRUCTIONS
Tow & Go Garage™
With the VTech®Go! Go! Smart Wheels®Tow & Go Garage™,
safety comes first. To ensure your child’s safety, adult assembly
is required.
1. With the Base right-side up, insert the Center Support, Pillar
Support, Elevator Support and Elevator Gate into the slots on
the Base, as shown below.You will hear a “click” sound to indicate
the pieces are secure.
2. With the Second Level Platform right-side up, attach it to the three
connected supports, as shown below. You will hear a “click” sound
to indicate the pieces are secure.

10
10
10
3. Next, assemble and attach the elevator components following the
stepsbelow:
A. Slide the Elevator Platform into the slot on the Elevator Wall,
as shown below. Lift the handle and press down on the Elevator
Platform to lower it.
B.Then, attach the Elevator Wall to the Base and Second Level
Platform, as shown below. You will hear a “click” sound to
indicate the Elevator Wall is secure.
C. Connect the Elevator Bracket to the Elevator Wall and
Elevator Gate, as shown below. Pull down on the Elevator
Bracket to make sure it is secure.