V-tech Toot-Toot Friends 2-in-1 Dinosaur Park Assembly Instructions

Parent’s Guide
2-in-1
Dinosaur Park

2
INTRODUCTION
Thank you for purchasing the VTech®Toot-Toot Friends™ 2-In-1
Dinosaur Park! Place the Park Ranger, Pterosaur and Triceratops
onto the MagicPoint™location to hear fun sounds and music!
Press the Light Up Buttons to feed the dinosaurs, or push the T-Rex
out of the gate to hear fun sounds! Easily transform the play set
between a dinosaur transportation truck and a dinosaur park for
even more role play fun!
3 Light Up Buttons
Gate
Mode Switch
Battery Box
Off/Volume
Switch
MagicPoint™
Location
Transform Buttons

3
INCLUDED IN THIS PACKAGE
NOTE: This toy is not intended for teething.
WARNING: Do not discharge any object other than the net provided
with this toy.
WARNING: Do not aim at eyes or face.
• One character - Pterosaur• One character - Park Ranger
• One character – Triceratops • One bowl of food
• One label sheet• One net

4
• One T-Rex
• One play set base
• One park sign
• One telescope
• One slider
• One small truck
• One door of small truck
• One net launcher
• One claw
• One trap platform
• One normal platform

5
WARNING:
All packing materials such as tape, plastic sheets, packaging
locks, removable tags, cable ties, cords and packaging screws
are not part of this toy and should be discarded for your child’s
safety.
NOTE:
Please keep this Parent’s Guide as it contains important
information.
ASSEMBLY INSTRUCTIONS
Adult assembly required. For your child’s safety, do not let
your child play with this product until it is fully assembled.
• Insert the net launcher into
the top of the small truck.
You will hear a click when it
is secure.
• Attach the door to the small
truck. Click in the top part
first, then the bottom part.

6
• Attach the upper part of the
T-Rex head onto its body.
Click in the left side first, then
the right side.
• Insert the telescope onto the
right side of the lookout. You
will hear a click when it is
secure.
• Attach the trap platform onto
the right side of the play set.
Click in one side first, then click
in the other side.
• Attach the other platform
onto the left side of the play
set. Click in one side first,
then click in the other side.
• Attach the park sign onto the
top of the play set. Click in
one side first, then click in
the other side.
• Attach the claw onto the
play set. Click in the top part
first, then the bottom part.

7
• Attach the T-Rex slider onto the front
of the play set. Click in one side first,
then click in the other side.
LABEL APPLICATION
Please stick the labels to the play set securely as indicated below.
2
3
4
5
6
79
10
11 13 16
15
14
12
8
1

8
1
2
3
4
6
9
10
13
16
15
14
12
8
5
7
11

9
GETTING STARTED
Battery Removal and Installation
1. Make sure the toy is turned OFF.
2. Locate the battery cover on
the back of the play set. Use a
screwdriver to loosen the screw.
Then, remove the cover.
3. If used or spent batteries are
present, remove these batteries
from the toy by pulling up on one
end of each battery.
4. Install 2 new AA size (LR6/AM-3)
batteries following the diagram
inside the battery box. (The
use of new alkaline batteries
is recommended for maximum
performance).
5. Replace the battery cover and
tighten the screw to secure.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Only batteries of the same or equivalent type as recommended
are to be used.
• Do not short-circuit the supply terminals.