V-tech Toot-Toot Drivers Construction Site User manual

Instruction Manual
Construction Site

C
M
Y
CM
MY
CY
CMY
K
Grow with VTech(101x127)bw1P-V2.pdf 1 08/18/2014 9:29:01

2
6 SmartPointTM Locations 3 Accessories
INTRODUCTION
Thank you for purchasing the VTech®Toot-Toot Drivers®
Construction Site.
Drive and work around this exciting Toot-Toot Drivers®Construction
Site by VTech®! Launch the included Toot-Toot dumper truck from
the very top and watch as it scoots down the corkscrew track onto
the cradle and down the second track!
SmartPointTM Dumper Truck
Launcher
Lift
Crane Cradle
Crane Tower
Switch Gate Hopper &
Drop Track

3
INCLUDED IN THIS PACKAGE
Three accessory
pieces
One SmartPointTM
dumper truck
Two spiral track
supports
One skip bracket One SmartPointTM
platform
One SmartPointTM
lift
Two tower
supports
One sign
One SmartPointTM
launcher
Five tracks (A,B,C,D,E)
One spiral track base

4
One lift cover
One SmartPointTM
parking base
One lift support
One lift wall
One crane base
Two exit gates One conveyor
support
One hanging
basket
One crane
One hanging
basket base
Two small lift
supports
One SmartPointTM
loading location

5
One conveyor belt
One crossing
track
One hopper
One arc-shaped plate
One tower bracket
One small link
bracket
One billboard
Two high
supports
One track switcher
One tower base
One rectangle plate
One guideboard

6
One crane cover
One high tower
link bracket
One guideboard
shaft
One low tower link
bracket
Crossing track
bracket
One long link
bracket
One short link
bracket
4 screws
•Label Sheet
•Quick Start Guide

7
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part
of this toy and should be discarded for your child’s safety.
NOTE:
Please save this Instruction Manual as it contains important information.
CAUTION:
Adult assembly required. This package contains small parts. For
your child’s safety, do not let your child play with the toy until it is fully
assembled.
If there are no locks inside the package, disregard this message.
Removing the Packaging Locks:
Pull out the packaging locks and discard.
Turn the packaging locks anticlockwise
several times.
INSTRUCTIONS
Battery Removal And Installation
Dumper Truck
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the
bottom of the Dumper Truck. Use a
screwdriver to loosen the screw and
then open the battery cover.
3. If used batteries are present,
remove from the unit by pulling up
on one end of each battery.

8
4. Install 2 new AAA (AM-4/LR03) batteries following the diagram
inside the battery box. (For best performance, alkaline
batteries or fully charged Ni-MH rechargeable batteries are
recommended).
5. Replace the battery cover and tighten the screw to secure.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
IMPORTANT: BATTERY INFORMATION
• Insertbatterieswiththecorrectpolarity(+and-).
• Donotmixoldandnewbatteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Onlybatteriesofthesameorequivalenttypeasrecommendedare
to be used.
• Donotshort-circuitthesupplyterminals.
• Removebatteriesduringlongperiodsofnon-use.
• Removeexhaustedbatteriesfromthetoy.
• Disposeofbatteriessafely.Donotdisposeofbatteriesinfire.
RECHARGEABLE BATTERIES:
• Removerechargeablebatteriesfromthetoybeforecharging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Donotchargenon-rechargeablebatteries.

9
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specified
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in the Batteries and Accumulators Regulation.
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Please dispose of your product and batteries responsibly.
In the UK, give this toy a second life by disposing of it at a
small electricals collection point* so all of its materials can
be recycled.
Learn more at:
www.vtech.co.uk/recycle
www.vtech.com.au/sustainability
* Visit www.recyclenow.com to see a list of collection points near
you.

10
LABEL APPLICATION
Please stick the labels to the play set securely as indicated on
the following page:
1234
6
7
8
9
10
5
11
12
13
14 14

11
3
2
4
5
10
11
13
6
14 14
89
12
7
1

12
ASSEMBLY INSTRUCTIONS
1. Assemble and attach the 3-loop spiral track components following
the steps as below:
A: Insert one Spiral Support into the Spiral Track Base, attach
the other Spiral Support. Make sure you hear a clicking sound to
confirm they are firmly connected. Tighten it with two screws to
secure.
B: Insert Track A into the Spiral Support, attach Track B to Track
A, attach Track C to Track B. Attach the Sign into the Tower
Top, insert the SmartPoint™ launcher to Track A. Insert the
Guideboard Shaft to Track B first, then attach the Guideboard
into the Guideboard Shaft.
With the VTech®Toot-Toot Drivers®Construction Site, safety
comes first. To ensure your child’s safety, adult assembly is required.

13
2. Assemble and attach the components for the Crossing Track
following the steps as below:
Insert the Track Switcher to the Crossing Track Bracket. Connect
the Crossing Track Bracket to the Tower bracket and Track C.
3. Assemble and attach the lift components following the steps
below:
A: Insert the two Small Lift Supports, the Lift Wall and the Lift
Support into the SmartPoint™ Parking Base.

14
B: Attach the SmartPoint™ Platform to the three Lift Supports
and the Lift Wall.
C: Attach the SmartPoint™ Platform to the Crossing Track. Insert
the Billboard into the SmartPoint™ Platform.
D: Insert the SmartPoint™ Parking Base into the Tower bracket.

15
E: Insert the Lift Cover to the Lift Wall, connect the SmartPoint™
Lift to the Lift Cover.
4. Assemble and attach the crane and tower components following the
steps as below:
A: Insert the Skip Bracket into the Two Tower Supports.
B: Insert the two High Supports into the Skip Bracket.

16
C: Attach the Hopper to the Skip Bracket.
D: Insert the Conveyor Support into the Conveyor Belt, insert the
SmartPoint™ Loading Location into the Conveyor Support, insert
an Exit Gate into the Conveyor Belt. Attach the Conveyor Belt to the
Hopper.
E: Insert the Crane Base into the two High Supports.

17
F: Insert the Crane Cradle into the Crane Cradle Base. Insert the
Crane Cradle into the Crane. Attach the Crane to the Crane Base.
Insert the Small Link Bracket into the Crane Base. Attach the Crane
Cover to the Crane.
5. Assemble and attach the construction tower components following
the steps as below:
A: Insert the Short Link Bracket into the High Tower Link Bracket.
Insert the Low Tower Link Bracket into the Short Link Bracket.

18
B: Insert the Tower Bracket into the Tower Base. Make sure you
hear the clicking sound to confirm they are firmly connected.
Tighten it with two screws to secure.
C: Connect the Tower Bracket to the Low Tower Link Bracket.
Connect the Tower Base to the High Tower Link Bracket.
D: Double check the connections between Track E, the Tower
Base and the High Tower Link Bracket as in the picture below.
Make sure you hear a clicking sound to confirm they are firmly
connected.
BACK
E: Attach Track E to Track D. Insert Track D into the Low Tower
Link bracket.

19
BACK
F: Insert the Rectangle Plate and the Arc-Shaped Plate into Track
D. Insert the other Exit Gate into Track E.
G: Insert the High Tower Link Bracket into the Tower Support.
Insert the Low Tower Link Bracket into the High Support.
H: Connect the Spiral Track Base and the High Tower Link
Bracket to the Long Link Bracket.