V-tech Toot-Toot Drivers Train Set Assembly Instructions

Parent’s Guide
Train Set
91-003715-001 UK

2
2
2
INTRODUCTION
Thank you for purchasing the Toot-Toot Drivers®Train Set. Travel
around the track triggering the four SmartPointTM locations included
on the train set. The motorised freight train can travel up and down
hills, on or off the tracks.
4SmartPointTM
Locations
Bridge
Crane
Unloading
Platform
Water Drum
Cargo Car
SmartPointTM Motorised
Freight Train

3
3
3
INCLUDED IN THIS PACKAGE
One SmartPointTM
motorised train
One train station
wall
One roof
One flag
One train station
platform
One 45° track One traffic light
One bridge trackTwo bridge
guard rails
NOTE: This toy is not intended for teething.
One bridge base One spiral track bottomOne spiral track top

4
4
4
One crane tower One crane arm One lifting hook
One crane tower
base
One road sign One track sign
One unloading
platform wall
One unloading platform One switch gate
for Y-track
One arch One gate Two water drums

5
5
5
One spiral track
support A
One spiral track
support B
One spiral track
support C
One adaptor
track A
One adaptor
track B
One 1/4 track,
female A
One 1/4 track,
male B
Two 1/4 tracks C Two track column
bases
Three 45° tracks,
female
Seven track columns

6
6
6
One Parent’s Guide
Seven 45° tracks, male A
Nine 1/8 tracks
Nine 1/8 flexible-tracks
One label sheet

7
7
7
NOTE:
This play set includes adaptors that allow connection with standard
Toot-Toot Drivers®tracks. The tracks are not compatible with snap
tracks. Adult assembly required.
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy and should be discarded for your child’s safety.
NOTE: Please keep user’s manual as it contains important information.
Adult assembly required.
Unlock the packaging locks:
Turn the packaging lock
anticlockwise several times.
Pull out and discard the packaging lock.

8
8
8
GETTING STARTED
BATTERY REMOVAL AND INSTALLATION
Train
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the
back of the train. Use a screwdriver
to loosen the screw.
3. If used or spent batteries are
present, remove these batteries
from the unit by pulling up on one
end of each battery.
4. Install 3 new AAA (AM-4/LR03) batteries following the diagram
inside the battery box. (The use of new alkaline batteries is
recommended for maximum performance).
5. Replace the battery cover and tighten the screw to secure.
BATTERY NOTICE
• UsenewalkalinebatteriesorfullychargedNI-MH(NickelMetal-
hydride) rechargeable batteries for best performance.
• Useonlybatteriesofthesameorequivalenttypeas
recommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard
(carbon-zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Removerechargeablebatteriesfromthetoybeforecharging(if
removable).
• Rechargeablebatteriesareonlytobechargedunderadult
supervision.

9
9
9
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates
they must not be disposed of in domestic waste as
they contain substances that can be damaging to the
environment and human health.
ThechemicalsymbolsHg,CdorPb,wheremarked,
indicate that the battery contains more than the
specifiedvalueofmercury(Hg),cadmium(Cd)orlead
(Pb) set out in Battery Directive (2006/66/EC).
The solid bar indicates that the product was placed on
the market after 13th August, 2005.
Helpprotecttheenvironmentbydisposingofyourproductor
batteries responsibly.
Formoreinformation,pleasevisit:
www.recycle-more.co.uk
www.recyclenow.com

10
10
10
LABEL APPLICATION
Please stick the labels to the play set securely as
indicated on the following pages:
28
23 20 13 14 15

11
11
11
8
1 1
21
3
4
1 11 1
2
16
12
11
10
22
96
7
5
27 24 25 27
26
19
17
18

12
12
12
ASSEMBLY INSTRUCTIONS
Toot-Toot Drivers®Train Set
With the Toot-Toot Drivers®Train Set, safety comes first. To
ensure your child’s safety, adult assembly is required.
1. Insert the two Guard Rails into the Bridge Track, then attach it
to the Bridge Base. Next, connect one 45° Track Male A, one
45° Track Female and one 45° Track Male A to the right side
of the base. Finally, attach two Flexible Tracks, one Adaptor
Track B, one Adaptor Track A and a 1/4 Track C as shown
below.
2. Connect one 45° Male Track A and one 45° Track Female to
the left side of the Bridge Track Base, then attach Flexible
Tracks as shown below.

13
13
13
3. Connect with the Y-Track as shown below.
4. Insert the Flag into the Roof, then attach the Roof to the Train
Station Wall as shown below.
5. Connect the Train Station Platform with the 45° Track on the
left and the 45° Male Track A on the right. Insert the Traffic
Light, then connect the Train Station Platform with the Train
Station Wall as shown.

14
14
14
6. Insert the Track Columns into the Track Column Base, then
connect them to the Train Station Platform.
7. Connect the Train Station Platform to the Bridge Track.
8. Attach the Crane Arm to the Crane Tower. Next, insert the
Crane Tower into the Crane Tower Base, then attach the
Lifting Hook.

15
15
15
9. Connect the Bottom Spiral Track to the Top Spiral Track, then
secure them with Spiral Track Supports A, Band C.
10. Next, insert the Crane into the Spiral Track, then connect
additional track pieces as shown in image B below.
11. Insert the Windmill and the Pump Lever into the Unloading
Platform.

16
16
16
12. Connect the Unloading Platform to the Spiral Track, then insert
the Road Sign and the Arch into the track.
13. Connect the Spiral Track to the right side of the Train Station
on the upper level.
14. Once you’ve completed the steps above, you are ready to play!
Arrange your tracks into the configurations below, or connect this
play set to other Toot-Toot Drivers®play sets and tracks (each
sold separately).

17
17
17
EXPAND & EXPLORE
Connect to the Toot-Toot Drivers®Track Set (as shown below) or
other Toot-Toot Drivers®play sets (each sold separately) to expand the
Train Set and inspire creativity .
PRODUCT FEATURES
Train
1. Motor/Manual/Off Selector Switch
To turn the Train On, Slide the
Motor/Manual/Off Selector Switch
to the Motor Mode ( ) or
Manual Play Mode position. To
turn the train Off, slide the Motor/
Manual/Off Selector Switch to the
Off position.

18
18
18
WARNING: For your child’s safety, only use the motorised
freight train on Toot-Toot Drivers®train tracks.
Do not roll the train on your clothing, body or
hair while the motorised train is turned on. If
something gets caught in the train’s wheels while
the motor is on, lift the train up so it is no longer
touching your child or slide the mode selector
switch to the off position to turn the motor off.
2. Automatic Shut-Off
To preserve battery life, the Train will automatically power
down after approximately 90 seconds without input when in the
Manual Play Mode position and approximately 330 seconds
without input when in Motor Mode. The unit can be turned on
again by pressing the Light Up button or the Chimney button,
pushing the Train quickly or triggering a SmartPointTM location.
NOTE: This product is in Try-Me mode in the packaging. After
opening the package, turn the Train off and on again to
proceed with normal play. If the unit powers down while
playing, we suggest changing the batteries.

19
19
19
ACTIVITIES
Motorised Train
1. Slide the Motor/Manual/Off
Selector to the Manual or
Motor ( ) position to turn the
Train On.You will hear a song, a
phrase and sounds. The light will
flash with the sounds.
2. Press the Light Up Button or
Chimney Button to hear sounds,
songs and phrases. The light will
flash with the sounds.
3. Push the Train to hear fun sounds.
If a melody is already playing, push
the vehicle to add fun sounds on
top of the melody. The light will
flash with the sounds.
4. For added fun, the Train interacts with the Toot-Toot Drivers®
Train Set. Simply put the Train on one of the play set’s four
SmartPointTM locations to see the light flash and hear fun
sounds, short tunes and phrases. The Train even interacts
with other Toot-Toot Drivers®play sets (each play set sold
separately).

20
20
20
ACTIVITIES
Train Set
1. Place the Train or any SmartPointTM vehicle (each sold
separately) on any of the play set’s four SmartPointTM locations
to trigger fun sounds, songs or phrases.
2. Place the Train on the SmartPointTM track on the Train Station
Platform to load the Water Drums.
3. Flip and lock the lever on the Bridge to change levels.