V-tech Cutie Paws Puppy Stroller Assembly Instructions

Cutie Paws Puppy Stroller
Parent’s Guide
91-003536-003 US
TM

2
2
2
INTRODUCTION
Thank you for purchasing the VTech
®
Cutie Paws Puppy Stroller™.
Little ones can place the adorable plush puppy in the stroller and take it
for a walk. The stroller features an adjustable canopy with attached flip
book for extra play, while the tray on the handle holds the accessories.
Handle
Canopy
Tray
Flip Book
Hair Dryer
Puppy
Shampoo Food
Bowl
Puppy
Button
Wheels
Wheel
Brush
Mode
Slider
Roller
Basket
Light-Up
Buttons
Off/Low/High
Volume Slider

3
3
3
INCLUDED IN THIS PACKAGE
• One plush puppy with • One electronic panel
• One handle • One tray
• One basket • One canopy
removable bandana

4
4
4
• One front wheel • Two rear wheels
• One hair dryer • One shampoo bottle
• One food bowl • One brush

5
5
5
• One label sheet
1
3
4
5
6
7
2
• One parent’s guide
WARNING:
All packing materials such as tape, plastic sheets, packaging
locks, removable tags, cable ties and packaging screws are not
part of this toy, and should be discarded for your child’s safety.
NOTE: Please keep this parent’s guide as it contains important
information.
ATTENTION :
Pour la sécurité de votre enfant, débarrassez-vous de tous
les produits d’emballage tels que rubans adhésifs, feuilles de
plastique, attaches, étiquettes et vis d’emballage. Ils ne font pas
partie du jouet.
NOTE : Il est conseillé de conserver ce guide des parents car il
comporte des informations importantes.
Adult assembly required.
Ce jouet doit être assemblé par un adulte.

6
6
6
Remove the Cable Ties:
There are two cable ties on the puppy. Use
a pair of scissors to cut these cable ties.
1. One is located at the back of the
puppy’s head.
2. One is located at the bottom of the
puppy’s feet.
WARNING: The cable ties are not part
of this toy and should be removed and
discarded for your child’s safety.
Unlock the packaging lock on the
electronic panel:
GETTING STARTED
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the
bottom of the unit.
3. Use a screwdriver to loosen the screw
and open the battery cover.
To unlock the packaging lock
on the electronic panel:
Rotate the packaging lock 90
degrees counterclockwise.
Pull out the packaging lock.
1
2

7
7
7
4. Install 2 new AA (AM-3/LR6) batteries into the battery box as
illustrated. (The use of new, alkaline batteries is recommended for
maximum performance.)
5. Replace the battery cover and tighten the screw to secure.
BATTERY NOTICE
• Use new alkaline batteries for maximum performance.
• Use only batteries of the same or equivalent type as recommended.
• Do not mix different types of batteries: alkaline, standard (carbon-
zinc) or rechargeable, or new and used batteries.
• Do not use damaged batteries.
• Insert batteries with the correct polarity.
• Do not short-circuit the battery terminals.
• Remove exhausted batteries from the toy.
• Remove batteries during long periods of non-use.
• Do not dispose of batteries in fire.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
ASSEMBLY INSTRUCTIONS
With the VTech®Cutie Paws Puppy Stroller™, safety comes first.
To ensure your child’s safety, adult assembly is required.

8
8
8
STEP 1 WHEELS
1. Each leg matches to one of the mounting
holes on the bottom of the basket. Slide
the leg wheel into its matching hole.
2. Push the wheels to be sure they are
securely in place. The wheels will click
into place when properly inserted.
STEP 2 HANDLE
Slide the two sides of the handle into the
mounting holes on the back of the basket.
You will hear the handle click into place
when properly inserted. If the handle is
inserted in the wrong direction, it can’t
slide in.
STEP 3 CANOPY
Slide the canopy into the mounting holes
on the rear sides of the basket. You will
hear it click into place when properly
inserted.
STEP 4 TRAY ON THE HANDLE
Slide the brackets of the tray into the
mounting holes on the sides of the handle.
You will hear the tray click into place when
properly inserted.
STEP 5 ELECTRONIC PANEL
Slide the electronic panel into the bracket
on the right side of the stroller basket.

9
9
9
LABEL APPLICATION
Labels have been added so you can customize your Cutie Paws
Puppy Stroller™. Please securely adhere the labels to the stroller
and accessories as indicated below.
1
3
4
5
6
7
2
12
56
7
3 4

10
10
10
PRODUCT FEATURES -
ELECTRONIC PANEL
1. Off/Low/High Volume Switch
To turn the unit ON, slide the Off/Low/
High Volume Switch to the High
Volume ( ) or Low Volume ( )
position. You will hear a song. To turn
the unit OFF, slide the Off/Low/High
Volume Switch to the Off ( ) position.
2. Mode Slider
Slide the Mode Slider to select one of
three modes: Learning Mode, Role-Play
Mode or Music Mode.
Mode Slider
Light-Up Buttons
Puppy Button
Off/Low/High
Volume Switch