V-tech ZoomiZooz Waterpark Assembly Instructions

Parent's Guide
Waterpark
UK
91-003861-000

3
3
3
INTRODUCTION
Thank you for purchasing the VTech®ZoomiZooz®Waterpark.
Your child will love tumbling the ZoomiZooz®down the waterfall or
launching them from the stingray, sliding them on the turtle lift, or
pressing the starfish button to watch them slide! Place the 3 exclusive
ZoomiZooz®on the Magic ZoomiZone which will magically recognise
them and introduce their names and fun characteristics!
Three ZoomiZooz®
Magic
ZoomiZone
OFF/Low/High Volume
Control Switch
One Pop Up
Button
One Light Up
Button
One Lift Button

4
4
4
INCLUDED IN THIS PACKAGE
One VTech®
ZoomiZooz®
Waterpark Base
One Turtle Base
One Lift Pole
One WaterTower Top
One Swirl Track
One Protection Shield
One Water Tower Base
One Lift Base 7 Small Screws
One Slide Track
One Lifeboat
One Plate

5
5
5
• One sheet of labels
• One Parent`s Guide
WARNING: All packing materials such as tape, plastic
sheets, packaging locks, removable tags,
cable ties, cords and packaging screws are
not part of this toy and should be discarded
for your child’s safety.
NOTE: Please keep this Parent`s Guide as it
contains important information.
WARNING: For your child’s safety, do not aim at face
or eyes when launching the ZoomiZooz®
animals. Do not put, or attempt to launch
anything other than the characters provided.
PenguinUnicornSupport
Hippo

6
6
6
GETTING STARTED
BATTERY REMOVAL AND INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the
bottom of the unit. Use a screwdriver
to loosen the screw.
3. If used or spent batteries are
present, remove these batteries from
the unit by pulling up on one end of
each battery.
4. Install 2 new AAA (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended
for maximum performance).
5. Replace the battery cover and
tighten the screw to secure the
battery cover.
BATTERY NOTICE
• Use new alkaline batteries or fully charged NI-MH (Nickel Metal-
hydride) rechargeable batteries for best performance.
• Use only batteries of the same or equivalent type as
recommended.
• Do not mix different types of batteries: alkaline, standard (carbon-
zinc) or rechargeable or new and used batteries.
• Do not use damaged batteries.
• Insert batteries with the correct polarity.
• Do not short-circuit the battery terminals.
• Remove exhausted batteries from the toy.
• Remove batteries during long periods of non-use.
• Do not dispose of batteries in fire.
• Do not charge non-rechargeable batteries.

7
7
7
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates
they must not be disposed of in domestic waste as
they contain substances that can be damaging to the
environment and human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specified
value of mercury (Hg), cadmium (Cd) or lead (Pb) set
out in Battery Directive (2006/66/EC).
The solid bar indicates that the product was placed on
the market after 13th August, 2005.
Help protect the environment by disposing of your product or
batteries responsibly.
For more information, please visit:
www.recycle-more.co.uk
www.recyclenow.com

8
8
8
WARNING:
With the VTech®ZoomiZooz®Waterpark safety comes first. To
ensure your child’s safety, adult assembly is required.
The package contains 7 small screws. For your child's safety,
do not let your child play with the toy until it is fully assembled.
The 7 screws that are used to link the play set need to be
regularly checked to ensure they are securely tight.
Please stick the labels to the play set securely as
indicated on the following page:

9
9
9
ASSEMBLY INSTRUCTIONS
With the VTech®Zoomiooz®Waterpark safety comes first. To
ensure your child’s safety, adult assembly is required.
1. Screw the Protection Shield onto the Swirl Track as in image
shown below with 4 small screws.
2. Screw the Swirl Track onto the Waterpark Base as image
shown below with 3 small screws.
3. Connect the Lift Base onto the
Waterpark Base.
4. Insert the Turtle Base onto the
Lift Pole.

1010
10
5. Insert the Lift Pole onto the Lift Base and the Swirl Track.
6. Connect the Slide Track onto the
Swirl Track and the Base
7. Insert the Water Tower Base onto
the Lift Base.
8. Insert the Water Tower Top onto the
Water Tower Base.
9. Insert the Lifeboat in to the slot.