VADO OMIKA OMI-SFMKWO/A-CP User manual

Wall kit
OMI-SFMKWO/A-CP
OMIKA
Keep for future reference
Installation Guide
where inspiration flows
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[e-mail]
www.vado.com
This instruction booklet covers models:
OMI-SFMKWO/A-CP
Version 1, 1-10-19

23
Please read these instructions carefully before starting installation and keep for
future reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and fittings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing Regulations.
To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.
Important - please read
General installation
When installed, the fitting must comply with the requirements of the Water Supply
(Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
For further information, contact the Water Regulations department of your local water
supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations
Advisory Scheme by email ([e-mail]) or telephone: [phone].
Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed
to remove debris. Failure to do so could result in damage or low flow from the mixer
unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 13.
The fitting of isolating valves to the inlet feed is advised for ease of maintenance.
Please take great care when installing not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
Contents of Packaging
Installation guide &
User manual
Wall outlet/holder
Hex key
Handset
Connecting tube
Shower hose with 2 washers
Wall kit
OMI-SFMKWO-CP
OMIKA
Keep for future reference
Installation Guide

4 5
Dimensions
45mm
30mm
56mm
100mm
104mm
120mm
G1/2"
16mm
40mm
221mm
G1/2"
Installation - Quick guide
X
X
x 2
=
12
35
4

6 7
Installation
Prepare the end of the pipe work with
a ½” fixed connector or other plumbing
fitting (not supplied).
Connect the water supply to the
connector and flush through.
Screw the connecting tube into the
connector. Measure the distance from
the front face of the tiles to the face of
the flange (e.g. X).
Remove the connecting tube, and cut off
the dimension Xfrom the end, remove
any burrs.
The connecting tube has two cutouts in
the thread to help cutting if necessary.
Refit the connecting tube and check
that the front face of the flange is level
or slightly below the face of the tiles.
Note: If the faces are not level remove
more from the end of the connecting
tube.
Using PTFE tape screw the connecting
tube into the connector. Use a 6mm hex
key to tighten the connecting tube. Cutouts
Cut here
X
X
Connecting tube
Tile face
Faces
should be
level
Flange face
Fixed
connector
Slide the outlet/holder over the
connecting tube making sure not to
damage the O-rings.
Position against the wall make sure it is
level and tighten the 2 x grub screws on
the underside with the supplied
hex key.
Apply a thin bead of silicone around the
outside to seal against the tiled surface.
Installation
Hex key
Connecting tube
Hose connection
Outlet
Place one of the rubber washers into the
nut end of the hose and attach it to the
outlet (see below).
Handset
Place the second rubber washer into the
cone end of the hose and screw to the
handset (see right).
Handset
Cone end
of hose
Rubber
washer
Nut end of
hose
Rubber
washer

8 9
The electroplating on this product is finished to the highest standard. Due care
needs to be taken to ensure the appearance is retained.
We recommend cleaning all products with a soft damp cloth ONLY and advise
strongly against the use of all aggressive/corrosive cleaning products i.e. powders
and liquids. If these instructions are not followed, this may invalidate your
guarantee in the event of a problem occurring.
Notes:Cleaning instructions:

11
All VADO products come with a 2 year guarantee as standard. Within this guarantee period VADO
will provide replacement parts and any labour [SEE NOTE 1] needed to complete the product
repair.
This standard guarantee may be extended by registering your product to give up to a 15 year
guarantee period. Once registered:
VADO chromed brassware and stainless steel products have a 15 year guarantee
(2 years parts and labour plus 13 years parts only).
VADO digital and i-tech products have a 6 year guarantee (2 year parts and labour plus 4 years
parts only).
All other VADO products have a 3 year guarantee (2 years parts and labour plus 1 year parts only)
[SEE NOTE 2].
VADO electric showers have a 2 years parts and labour guarantee.
Guarantee conditions
Our products are guaranteed against manufacturing defects from the date of purchase until the
expiry of the relevant guarantee period shown above.
The guarantee is only valid if:
• The product has been installed, used and maintained in accordance with VADO’s instructions
and subjected to normal use only.
• The defect is not due to use of an unsuitable or inadequate water or power supply.
• The defect is not due to accident, misuse, neglect or incorrect/inappropriate repair (other than by
VADO or VADO authorised agents) or damage caused by foreign objects or substances.
• The extended guarantee is only available if you have completed the Guarantee Registration Process.
This can be done via the VADO website or via phone to our aftersales team. Registration must be
completed within 6 months from date of purchase.
Under the extended guarantee period VADO will, at its option, offer to supply any replacement
product (or component part) assessed to be defective [SEE NOTE 3].
The guarantee (whether standard or extended) is non-transferable to any subsequent owner.
All claims under the guarantee should be notified in the first instance to our Aftersales
department, contact details below, this must be done no later than the last day of the relevant
guarantee period. All claims must be accompanied by proof of purchase (sales receipt or delivery
note) from an official VADO dealer.
The guarantee does not extend to any consequential loss or damage.
After repair or replacement, the relevant guarantee period will be calculated from the original
date of purchase.
VADO operates a policy of continuous product development and therefore reserves the right to
change the product, packaging and documentation specifications without notice.
NOTES:
[1] Labour via our engineer network is only available in the UK. Attendance by a VADO engineer or
sub-contract engineer will be under our standard terms and conditions.
[2] VADO spare parts and shower hoses are under a parts only guarantee.
[3] VADO reserves the right to charge in advance for a product (or replacement part) pending
collection and investigation (at VADO expense) to confirm a defect is due to a manufacturing issue.
If a defect is found the charge will be refunded or cancelled.
This guarantee is in addition to and does not affect your statutory rights as a consumer.
Tel: [phone]
Email: aftersal[email protected]om
Guarantee
10
Notes: