VADO OMIKA OMI-133 User manual

Floor Mounted Bath Shower Mixer
133
OMIKA
Keep for future reference
Installation Guide
where inspiration flows
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[e-mail]
www.vado.com
This instruction booklet covers model:
OMI-133.
Version 1, 1-8-17

23
Important information.............................................. 3
General installation...................................................3
Operating Specifications ...........................................3
Contents of packaging ..............................................4
Dimensions................................................................5
Installation - Quick guide..........................................6
Installation.................................................................8
Installation - Shower...............................................11
Contents
Please read these instructions carefully before starting installation and keep for
future reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and fittings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing Regulations.
To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.
General installation
Operating Specifications
Important - please read
Operating Pressure
Minimum operating pressure 1 bar
Maximum operating pressure 5 bar
This fitting is a mixing device and therefore water supplies should be reasonably
balanced.
When installed, the fitting must comply with the requirements of the Water Supply
(Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
For further information, contact the Water Regulations department of your local water
supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations
Advisory Scheme by email ([e-mail]) or telephone: [phone].
Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed
to remove debris. Failure to do so could result in damage or low flow from the mixer
unit.
The fitting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.

4 5
Contents of Packaging
Installation guide &
User manual
Shroud
Handset
Hex keys x 3
Cap screws &
washers x 8
Tap/upstand
Floor Mounted Bath Shower Mixer
133
OMIKA
Keep for future reference
Installation Guide
WHERE
INSPIRATION
FLOWS
OMIKA
Floor Mounted Bath Shower Mixer
User Guide
Accessory box
Shower hose
Base
Base connection
Valve dimensions
75mm
215mm
67mm
110mm
30mm
154mm
100mm
Ø40mm
870mm
16.5mm

6 7
Installation - Quick guideInstallation - Quick guide
1
3
4
2
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
–
>105mm
?
x 3
5
7
9
6
8
10
90mm90mm

8 9
Installation
Position the base in the desired location,
mark the 3 fixing holes. Remove the base
and drill the 3 x holes to the required
diameter and depth to suit your fixings.
Fit the base in position, but do not tighten.
Use the adjusting screws to level the seat,
when satisfied with the level, finally tighten
the fixings.
Warning! Please check for any hidden
cables and pipes before drilling holes.
The base must be recessed below the final
floor level by at least 105mm.
Connect the hot and cold supplies to the
base. The hot should be fixed to the outlet
marked Hand the cold fixed to C.
There are 3 fixing positions and 3 levelling
bolts.
Use suitable fixings (not supplied) for your
substrate e.g. expansion bolts for concrete,
or coach screws for wood.
Installation
–
>105mm
Slide the shroud onto base of upstand.
To ensure smooth movement of shroud
and prevent scratching during installation,
please use a suitable silicone based
lubricant.
Be sure to keep the shroud level, and
raise both sides equally.
Using the 4 supplied cap screws and
washers secure the base connection onto
the bottom of the tap/upstand. Ensure the
correct tap/upstand pipes are connected to
the asigned holes in the base connection -
the Hshould be connected to the hot inlet
and the Cshould be connected to the cold
inlet.
Turn on the water and check for any leaks in
the pipe work.
Turn off the water supply.
Remove the grub screw and pull the drain
valve out of the base.
Drain valve
Shroud
Tap/upstand
pipes
Upstand
Cold inletHot inlet
Levelling
bolts x 3
Fixing slot x 3
Fixing slot Levelling bolt
Cold inlet
Hot inlet

11
10
Installation - shower
Handset
Place one of the rubber
washer into the cone end of
the hose and screw to the
handset.
Place the cone into the
bracket
Outlet
Place the second rubber
washer into the nut end of
the hose and attach it to the
mixer outlet.
Cone end
of hose
Washer
Handset
Rubber
washer
Nut end
of hose
Installation
Slide the shroud down until it makes
connect with the floor.
Be sure to keep the shroud level, and
lower both sides equally.
Finish the floor covering down to a
dimension of 90mm x 90mm.
Keep the tap/upstand protected while the
floor is being completed.
Place the base connection onto the base.
Rotate the tap/upstand until the outlet is in
the desired position.
When satisfied, secure using the x 4
supplied cap screws and washers.
90mm90mm

Guarantee
WHERE
INSPIRATION
FLOWS
OMIKA
Floor Mounted Bath Shower Mixer
User Guide
All VADO products come with a 2 year guarantee as standard. Within this guarantee
period VADO will provide replacement parts and any labour [SEE NOTE 1] needed to
complete the product repair.
This standard guarantee may be extended by registering your product to give up to a 12
year guarantee period. Once registered:
VADO chromed brassware and stainless steel products have a 12 year guarantee
(2 years parts and labour plus 10 years parts only).
VADO digital and i-tech products have a 6 year guarantee (2 year parts and labour plus 4
years parts only).
All other VADO products have a 3 year guarantee (2 years parts and labour plus 1 year
parts only) [SEE NOTE 2].
VADO electric showers have a 2 years parts and labour guarantee.
Guarantee conditions
Our products are guaranteed against manufacturing defects from the date of purchase
until the expiry of the relevant guarantee period shown above.
The guarantee is only valid if:
• The product has been installed, used and maintained in accordance with VADO’s
instructions and subjected to normal use only.
• The defect is not due to use of an unsuitable or inadequate water or power supply.
• The defect is not due to accident, misuse, neglect or incorrect/inappropriate repair
(other than by VADO or VADO authorised agents) or damage caused by foreign objects or
substances.
• The extended guarantee is only available if you have completed the Guarantee Registration
Process. This can be done via the VADO website or via phone to our aftersales team.
Registration must be completed within 6 months from date of purchase.
Under the extended guarantee period VADO will, at its option, offer to supply any
replacement product (or component part) assessed to be defective [SEE NOTE 3].
The guarantee (whether standard or extended) is non-transferable to any subsequent owner.
All claims under the guarantee should be notified in the first instance to our Aftersales
department, contact details below, this must be done no later than the last day of the
relevant guarantee period. All claims must be accompanied by proof of purchase (sales
receipt or delivery note) from an official VADO dealer.
The guarantee does not extend to any consequential loss or damage.
After repair or replacement, the relevant guarantee period will be calculated from the
original date of purchase.
VADO operates a policy of continuous product development and therefore reserves the right
to change the product, packaging and documentation specifications without notice.
NOTES:
[1] Labour via our engineer network is only available in the UK. Attendance by a VADO
engineer or sub-contract engineer will be under our standard terms and conditions.
[2] VADO spare parts and shower hoses are under a parts only guarantee.
[3] VADO reserves the right to charge in advance for a product (or replacement part)
pending collection and investigation (at VADO expense) to confirm a defect is due to a
manufacturing issue. If a defect is found the charge will be refunded or cancelled.
This guarantee is in addition to and does not affect your statutory rights as a consumer.
Tel: [phone]
Email: [e-mail]

Operation
Turning the temperature control handle in the direction of
the arrows increases/decreases the temperature
Turning the diverter handle
anti-clockwise activates the
flow of water progressively
to the bath.
Hot
Cold
Off
HandsetBath
Turning the diverter handle
clockwise activates the
flow of water progressively
to the handset.
Welcome
Thank you for choosing VADO
Our products can be found in some of the most prestigious
hotel, commercial and residential developments across the
world, therefore you can expect exceptional product quality and
outstanding customer service.
This product has passed through stringent quality assurance
processes coupled with demanding lifecycle mechanical testing
to ensure it reaches the exacting standards that allow us to
offer our premium 12 year guarantee.
We work to ensure our product designs are harmonious with
all sanitaryware, so when you choose VADO, your choice of
coordinating items is unlimited.
With VADO, you can really let your inspiration flow.
For any technical or operational queries please contact our
experienced aftersales team on 01934 745163.
Vado, Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[e-mail]
www.vado.com

Cleaning instructions:
The electroplating on this product is finished to the
highest standard. Due care needs to be taken to ensure
the appearance is retained.
We recommend cleaning all products with a soft damp
cloth ONLY and advise strongly against the use of all
aggressive/corrosive cleaning products i.e. powders
and liquids. If these instructions are not followed, this
may invalidate your guarantee in the event of a problem
occurring.
Notes

Parts list: Parts:
Item Description Part Code Quantity
1Mixing Cartridge FL-601-33Q 1
2Diverter FL-803-33/2X 1
3Handle OMI-1/133-C/P 1
4Outlet Bracket OMI-133-OUTLETBRACK 1
5Handset OMI-HANDSET-C/P 1
6Shower Hose SH-012-150-CP-LB 1
7Shroud OMI-133/SHROUD-C/P 1
8Adaptor OMI-133-CONC/ADAPTOR 1
9Base CON-133-BR 1
10 Installation guide
& User manual
1
Floor Mounted Bath Shower Mixer
133
OMIKA
Keep for future reference
Installation Guide
WHERE
INSPIRATION
FLOWS
OMIKA
FloorMounted Bath Shower Mixer
UserGuide
8
2
4
10
3
7
6
1
5
9