VADO WG-81389-C Installation and operating instructions

WG-81389-C/P & WG-81552-C/P
Pop up bath ller wastes
Installation & maintenance instructions
Please leave these instructions with the customer
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[email protected]
www.vado-uk.com
Guarantee
Customer/technical services
For any technical or installation queries please contact Vado on 01934 745163.
GUARANTEE REGISTRATION
NAME
ADDRESS
RETAILER
ADDRESS
PURCHASE DATE
PRODUCT DESCRIPTION
WHO INSTALLED THE PRODUCT?
FOR VADO USE
POSTCODE
POSTCODE
ARTICLE NUMBER (SEE BOX)
RETAILER PLUMBER BUILDER SELF
This product is guaranteed against manufacturing defects from the date of purchase until the expiry of the relevant
guarantee period shown below.
The guarantee is only valid if:-
1. The product has been installed, used and maintained in accordance with Vado’s instructions and subjected to
normal use only.
2. The defect is not due to use of an unsuitable or inadequate water or power supply.
3. The defect is not due to accident, misuse, neglect or repair other than by Vado or Vado authorised agents or
damage caused by foreign objects or substances.
4. We have received from you the completed Guarantee Registration Form. Vado accepts no responsibility for any
forms lost in the post and returns by registered means is therefore recommended.
Under this guarantee (which is non-transferable) Vado will, at its option, repair or replace free of charge any product
(or replacement part) found to be defective. The guarantee does not extend to any consequential loss or damage.
After repair or replacement the relevant guarantee period will be calculated from the original date of purchase.
The relevant guarantee periods are:-
1. Twelve years on chrome nish products.
2. Six years on Vado Identity products.
3. Three years on all other products with the exception of Stuart Turner Pumps which carry a 2 year Guarantee on
Monsoon Range and 1 Year Guarantee on Showermate Range.
All claims under the guarantee must be submitted in writing to the person who supplied the product to you and
must be received no later than the last day of the relevant guarantee period. All claims must be accompanied by
proof of purchase (sales receipt or delivery note).
Vado operates a policy of continuous product development and therefore reserves the right to change the product,
packaging and documentation specications without notice.
This guarantee is in addition to and does not aect your statutory rights as a consumer.

Important - please read
27
Installers/users notes
Operating Specications
Operating Pressure:
Minimum operating pressure 1 bar
Maximum operating pressure 5 bar
Please read these instructions carefully before starting installation and keep for future
reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and ttings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing (UK:BS6700) Regulations.
We strongly recommend that you use a qualied and registered plumber.
Installer must comply with current regulations.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
Care of the waste
Our products are nished to the highest standard and due care needs to be taken to
ensure their looks are retained.
We recommend cleaning all products with a soft damp cloth ONLY and advise strongly
against the use of ALL cleaning products i.e. powders and liquids.
Use only mild soap and water to clean the surface of your mixer valve and dry wit a
soft dry cloth.
If the above instructions are not followed this will invalidate your guarantee in the
event of a problem occurring.

63
Assembly and installation 81552
From below push the top part of the rubber seal up through the hole in the bath.
Push the waste housing up into the seal and hold in place.
From inside the bath place the waste ange over the seal and secure in position using
the screw, do not over tighten as might damage the bath.
Slide the compression nut, washer and seal over the pipe, push the pipe fully into the
waste assembly, slide along the seal and washer and nally screw on the nut, hand
tight only. Push in the plug.
Decreasing the pipe length.
The pipe can be shortened by carefully cutting, removing any burrs. Ensure all calculations
are correct before cutting the pipe. Finish by following the above procedure.
Plug adjustment
To adjust the opening and/or closing position of the plug.
With a at screwdriver loosen the adjusting screw to the required position, tighten the
locking nut, and ret into the waste. Test, and readjust if necessary.
Plug
Seal
Locking nut
Adjusting screw
Waste screw
Waste ange
with seal
Seal
Compression
nut Washer
Seal
Overow/waste
assembly
Overow pipe
Cable to pop up waste
Adjusting
screw
Locking nut
Operation
Turning the handle anti-clockwise closes the plug.Turning the handle clockwise opens the plug.
Assembly and installation 81389
The length of the overow pipe can be adjusted by pulling apart or pushing together
the inner and outer overow pipes.
Should you need to reduce the length even more, pull the outer overow out of the
collet, cut both the outer overow pipe and the inner overow pipe to the required
length, remove any burrs and reassembly.
Ensure all calculations are correct before cutting pipes.
Remove the blanking plug(s) from the overow assembly. Using PTFE tape t the inlet
elbow(s).
Push the rubber seal onto the overow/waste assembly, and from the outside hold in
place over the bath overow hole.
Screw on the overow housing, tighten with an allen key.
Caution: do not overtighten as this may damage the parts and/or the bath.
Place the overow fascia over the overow housing, make sure the slots for the outlet
and overow are on the underside. Tighten by screwing the grubscrew located on the
underside of the overow fascia.
Connect to the supply pipe work.
Overow/waste
assembly
Rubber seal
Overow fascia
Inner overow pipe
Inlet elbow
Inlet elbow
Overow
housing
Allen key
Allen key socket
Outlet and
overow slots
Outer overow pipe
Collet

45
Assembly and installation 81389 Assembly and installation 81552
The length of the overow pipe can be adjusted by pulling apart or pushing together
the inner and outer overow pipes.
Should you need to reduce the length even more, pull the outer overow out of the
collet, cut both the outer overow pipe and the inner overow pipe to the required
length, remove any burrs and reassembly.
Ensure all calculations are correct before cutting pipes.
Remove the blanking plug(s) from the overow assembly. Using PTFE tape t the inlet
elbow(s).
Push the rubber seal onto the overow/waste assembly, and from the outside push
the shaft through the bath overow hole and hold in place.
Slide the overow housing onto the waste assembly and push up until it meets the
bath, make sure that the slots for lling and overow are on the underside. Secure
using the retaining nut and tighten (do not over tighten as this may damage the parts
and/or the bath).
Push the handle onto the assembly, with the small lever at the 12 o’clock position,
secure the handle using the grub screw in the underside and tighten with the
supplied allen key, push on the screw cover.
Connect to the supply pipework.
Overow/waste
assembly
Retaining nut
Rubber seal
Overow
housing
Handle
Inlet elbow
Screw cover
Inlet elbow
Cable to pop
up waste
Inner overow pipe
Outer overow pipe
Collet
Push the seal onto the waste assembly
From below push the assembly up under the hole in the bath, and hold in place.
From inside the bath screw the waste ange into the assembly and tighten by hand,
(do not over tighten as this may damage the parts and/or the bath).
Slide the compression nut, washer and seal over the pipe, push the pipe fully into the
waste assembly, slide along the seal and washer and nally screw on the nut, hand
tight only.
Screw on the plug.
Decreasing the pipe length.
The pipe can be shortened by carefully cutting, removing any burrs.
Ensure all calculations are correct before cutting the pipe.
Finish by following the above procedure.
Operation
Plug
Seal
Seal
Compression
nut
Washer
Seal
Overow/waste
assembly
Overow pipe
Waste ange
with seal
Push down again to close the plug.Push down to open the plug.