Vance and hines 48241 User manual

INSTALLATION INSTRUCTIONS:
2022 HONDA NAVI
UPSWEEP FULL EXHAUST SYSTEM BLACK
PART# 48241
Page 1 of 4 H520IN
Congratulations, you have purchased the nest exhaust system available for your motorcycle. Your Vance & Hines exhaust
is designed and crafted for performance, quality, and style. Please follow the instructions below, check exhaust system for
missing or damaged parts and if you need any assistance please contact our technical support line [phone].
Fits 2022 Honda Navi models
1
PARTS LIST
PART NO. Description Qty.
1 H182FP Exhaust System 1
21275-P Mounting Bracket 1
3A949HW M10X1.25X25mm 2
4A304HW 1/4-20 x 1/2 Button
Head Screw
2

STOCK SYSTEM REMOVAL
1. Remove the two cylinder exhaust port nuts from head pipe, located at the cylinder
head. (Save for reuse)
2. Remove the splashguard bolt, located on the rear fender.
3. Remove the two exhaust chassis mount bolts.
4. Remove the complete exhaust system and set aside.
5. Check the condition of exhaust gasket and replace if worn or damaged.
TOOLS REQUIRED
Page 2 of 4 H520IN
Allen Wrench: 4mm Sockets: 10mm, 14mm, 15mm
Ratchets: 1/4”, 3/8”
Extentions: 1/4”DR EXT Bar 6”
3/8 ”DR EXT Bar 6”
2
3
4
HARDWARE

Page 3 of 4 H520IN
VANCE & HINES SYSTEM INSTALLATION
1. Install mounting bracket (1275-P) using supplied M10 bolts (A949HW). (Do not fully
tighten at this time).
2. Install exhaust using stock exhaust port nuts. (Do not fully tighten at this time).
3. Fasten exhaust to mounting bracket using the two supplied 1/4-20 screws (A304HW).
4. Tighten cylinder exhaust port nuts evenly.
5. Tighten mufer mounting screws.
6. Tighten mounting bracket bolts.
EXHAUST CARE (BLACK)
1. When installing a new set of black pipes, make sure your hands are clean and free
from oil. After installation, thoroughly clean pipes with warm soapy water and a soft
cloth. Dry with a clean towel to remove any residue before starting the motorcycle. Do
NOT use anything abrasive to clean pipes.
2. Avoid long periods of idling as this can cause discoloration.
3. Intake leaks can cause the engine to run lean and overheat, this could lead to
discoloration.
4. Make sure there are no exhaust leaks at the junction of the exhaust pipes and the
cylinder head. We recommend replacing gaskets if they are worn.

D992IN RevA
Emissions Notice:
In California, in order to meet Air Resources Board emissions requirements, certain aftermarket part applications
have been identied as replacements, and others have received ARB Executive Orders. All other emissions
related aftermarket parts are for competition use only. A list of replacement parts and EO parts, and
corresponding tment is provided at vanceandhines.com/California.
Warranty:
All Vance & Hines products are warranted against defects in material and workmanship for a period of 90 days.
This warranty does not cover discoloration or rust. This warranty shall be limited to the repair or replacement of
the product, which may be proven defective under normal use. Vance & Hines will not warranty any system
that has been abused, misused, improperly installed or modied.
Dealers or distributors are not authorized to make dispositions binding upon Vance & Hines. Vance & Hines will
not be responsible for any labor charges incurred in removing or replacing any system under warranty. A return
authorization number and a copy of the original purchase invoice must accompany all returns. Parts returned
without a return authorization may be refused.
For Printing on WHITE ONLY-KNOCKOUT
VERSION-BIZ CARDS
13861 ROSECRANS AVENUE / SANTA FE SPRINGS, CA 90670
SALES: [phone]
TECHNICAL: [phone]
FAX: [phone]
Page 4 of 4