Vance and hines Competition Series User manual

Part Number 75-110-14
V-Rod Muscle Competition Series Slip-Ons
Exhaust System (09-10)
Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your Vance & Hines
exhaust is designed and crafted for maximum performance, a great sound and unbeatable style. Please follow the
instructions below, check exhaust system for missing or damaged parts and if you need any assistance please contact
our technical support line [phone].
ATTENTION:
This exhaust system is for racing purposes only.
STOCK EXHAUST SYSTEM REMOVAL
Please remove the following:
1. To remove the stock mufflers loosen and remove the two nuts holding the muffler to the passenger foot-peg.
Remove foot-peg assembly and set aside. Loosen and remove the single nut towards rear of the muffler
which holds the muffler to the round bar section of the foot-peg/exhaust bracket. Loosen muffler clamp and
pull muffler away from head pipe to set aside. Repeat for both sides.
COMPETITION SERIES EXHAUST SYSTEM INSTALLATION
1. Install supplied muffler clamps onto head pipes and leave loose.
2. Slide Mufflers onto stock head pipes being sure that the brackets go onto the footpeg studs and rear bracket
studs.
3. Reinstall foot-pegs and tighten the three mounting nuts on each side.
4. Tighten muffler clamps, torque to 75 in.lbs.
5. Clean all fingerprints from the exhaust using a contact cleaner (or other non flammable cleaner). Fingerprints
will leave stains on the pipe once the motorcycle is started.
6. You are now ready to start the motorcycle.
Note: After initial ride it is recommended to re-torque the baffle screw to 8-10 lb. using a 5/32” allen wrench.
For best results, we recommend fuel injection mapping for your new combination using a Fuelpak or Power
Commander. Settings for the Fuelpak and some Power Commander maps are available on our website at
www.vanceandhines.com
Vance & Hines
13861 Rosecrans Ave, Santa Fe Springs, CA90670
Phone: [phone], Fax: [phone]
E-mail: [email protected]
Web: www.vanceandhines.com
Opening Hours – Monday through Friday, 8am – 5pm, Pasific Standard Time
Vance & Hines exhaust systems are warranted against defects in material and workmanship for a period of 90 days from the date of
purchase from an authorized dealer. This warranty does not cover discoloration of any coated finishes.This warranty is limited to the
repair or replacement of a product proven to be defective from normal use. Vance & Hines exhaust systems are designed to fit and
operate on OEM motor and chassis . This warranty does not cover any product subject to abuse , misuse, improper installation or
modification.
D188IN – Page 1 – Revision 5

75-110-14: V-ROD MUSCLE COMPETITION SERIES SLIP-ONS
PNC EXHAUST SYSTEM
DRAG SPECIALTIES PART#: 1801-0343 STOCK EXHAUST: 25.6 lbs 75-104-10 EXHAUST: 14 lbs
75-110-14 PARTS LIST
PART NO. DESCRIPTION QTY.
D271RP Muscle Muffler Assy. Lt 1 D270RP Muscle Muffler Assy. Lt 1
A210NP Name Plate, Rt (2.5") 1 A211NP Name Plate, Lt (2.5") 1
A506HW Rivet 4 A334HW System Clamp, Ø1 7/8" 2
A120BEC Muscle Slip-Ons EndCap Rt. 1 A125BEC Muscle Slip-Ons EndCap Lt. 1
A122R Baffle Core Assy. 2
A444HW 18-8 SS Capscrew 10-32, 3/8" 6 A445HW BHCS 1/4"-20 x 5/8", Zinc 2 A235HW BHCS 1/4"-20 x 1/2", Zinc 2 A112HW Flat Washer Zinc, 1/4" 4 A115HW Lock Washer Zinc, 1/4" 4
A261FG Baffle Sock 2
MUSCLE MUFFLER PNC ASSY. LEFT D271RP
MUSCLE MUFFLER PNC ASSY.RIGHT D270RP
ENDCAP LT A125BEC BAFFLE CORE WELDED
ASSY. A122R
RIVET
A506HW
LOCK WASHER
A115HW
BOLT BUTTON
HEAD A445HW
FLAT WASHER
A112HW
BOLT BUTTON
HEAD A235HW
END CAP, RT
A120BEC
NAME PLATE
A210NP
CLAMP
A334HW
BOLT
A444HW
NAME PLATE
A211NP
BAFFLEPACKING
SOCKA261FG
D188IN – Page 2 – Revision 5