Vanderbilt CFMW3025 Instruction sheet

© Vanderbilt 2016
1
CFMW3025
3 Megapixel IP Indoor Dome
Camera
Configuration

© Vanderbilt 2016
2
Contents
1Copyright .................................................................................................4
2About this document ..............................................................................5
2.1 Content of document.................................................................................5
2.2 Meaning of symbols ..................................................................................5
2.3 Target group..............................................................................................5
3Safety........................................................................................................6
3.1 General safety precautions.......................................................................6
3.2 Transport...................................................................................................6
3.3 Installation.................................................................................................6
3.4 Maintenance..............................................................................................6
3.5 Sensor characteristics...............................................................................7
4EU-directives ...........................................................................................8
5Technical data .........................................................................................9
6Details for ordering...............................................................................10
6.1 Package contents....................................................................................10
7Camera part and connector definition................................................11
7.1 Camera part definition.............................................................................11
7.2 Connector pin definition ..........................................................................11
7.2.1 Digital I/O terminal...................................................................................11
7.2.2 Power terminal ........................................................................................12
7.2.3 Video out connector ................................................................................12
7.2.4 Default/Reset buttons..............................................................................12
7.2.5 SD card ...................................................................................................12
8Installing the camera ............................................................................13
8.1 Precautions .............................................................................................13
8.1.1 SD memory card .....................................................................................13
8.1.2 Power supply...........................................................................................13
8.2 Concept of the network camera..............................................................14
8.3 Setting network camera environment .....................................................14
8.4 Connecting the camera and personal computer via network..................14
8.5 Using the camera search application "Webcam IP Manager" ................16
8.6 Login dialog.............................................................................................18
8.7 Viewing and listening ..............................................................................19
8.8 Resolution ...............................................................................................24
9Configuration.........................................................................................25
9.1 Compression...........................................................................................25
9.2 Network settings......................................................................................26
9.2.1 Basic........................................................................................................26
9.2.2 DDNS Settings........................................................................................28
9.2.3 FTP Server..............................................................................................28
9.2.4 RTSP.......................................................................................................29
9.2.5 HTTPS.....................................................................................................29
9.2.6 IEEE802.1X.............................................................................................30
9.2.7 SNMP......................................................................................................31
9.2.8 3GPP.......................................................................................................31
9.3 Image parameter.....................................................................................32
9.3.1 Basic camera settings.............................................................................32
9.3.2 Camera mask zone settings....................................................................35
9.3.3 Camera cropping settings.......................................................................37
9.3.4 Camera OSD settings.............................................................................37

© Vanderbilt 2016
3
9.4 Alarm.......................................................................................................39
9.4.1 Alarm.......................................................................................................39
9.4.2 Audio event upload .................................................................................43
9.4.3 Alarm server............................................................................................44
9.5 Record.....................................................................................................46
9.5.1 Basic .......................................................................................................46
9.5.2 FTP Recording Basic..............................................................................47
9.5.3 SD recording ...........................................................................................49
9.5.4 Email recording .......................................................................................50
9.5.5 NAS recording.........................................................................................54
9.6 Audio.......................................................................................................55
9.7 Date / Time..............................................................................................56
9.8 Access protection....................................................................................57
9.8.1 Administrator...........................................................................................57
9.8.2 User list ...................................................................................................58
9.9 Firewall....................................................................................................58
9.9.1 IP Address filter.......................................................................................58
9.9.2 Forbidden ports.......................................................................................60
9.9.3 Forbidden protocols ................................................................................60
9.10 System ....................................................................................................61
9.10.1 Settings ...................................................................................................61
9.10.2 Update.....................................................................................................62
9.10.3 Configuration...........................................................................................63
9.10.4 Back focus...............................................................................................64
9.10.5 Temperature............................................................................................64
9.10.6 Calibration...............................................................................................64
9.10.7 Self-Testing.............................................................................................65
9.11 Log ..........................................................................................................66
9.12 Notice......................................................................................................66
10 Utility program application ..................................................................67
10.1 NAS player setup....................................................................................67
10.2 Audio recording setup.............................................................................67
10.3 Firmware update setup ...........................................................................67
11 Maintenance ..........................................................................................69
12 Disposal .................................................................................................70
Keyword index.......................................................................................................71

Copyright
© Vanderbilt 2016
4
1 Copyright
Liefermöglichkeiten und technische Änderungen vorbehalten.
Data and design subject to change without notice. / Supply subject to availability.
© 2017 Copyright by Vanderbilt
Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor. Der Empfänger erkennt diese Rechte
an und wird dieses Dokument nicht ohne unsere vorgängige schriftliche Ermächtigung ganz oder teilweise Dritten zugänglich machen oder
außerhalb des Zweckes verwenden, zu dem es ihm übergeben worden ist.
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without
our prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.

About this document
© Vanderbilt 2016
5
2 About this document
2.1 Content of document
This document contains information on the configuration of the product.
2.2 Meaning of symbols
Orientation guide
[-> 3] Cross-reference
Save Button
<Ctrl> Key
Tips and information
2.3 Target group
Commissioning personnel
Configure the product at
the place of installation accord-
ing to customer-specific re-
quirements.
Check the product opera-
bility and release the product
for use by the operator.
Searches for and corrects
malfunctions.
Has obtained suitable specialist training
for the function and for the products.
Has attended the training courses for
commissioning personnel.
Operating personnel
Performs the procedures
for proper operation of the
product.
No particular qualification required.
Has received instruction from the opera-
tional startup personnel.

Safety
© Vanderbilt 2016
6
3 Safety
3.1 General safety precautions
Read the general safety precautions before in-
stalling/configuring/operating the device.
Follow all warnings and instructions marked on the device.
Keep this document for reference purposes.
This document must always accompany the product.
Liability claim
Use only spare parts and accessories that have been approved by the
manufacturer.
3.2 Transport
Keep the packaging material for future transportation.
Do not expose the device to mechanical vibrations or shocks.
3.3 Installation
It is recommended that all preparatory work (e.g. fitting of accessories)
be carried out in a workshop prior to final installation.
The environmental conditions recommended by the manufacturer must
be observed. See section 'technical data'.
Do not operate the device close to sources of powerful electromagnetic
radiation.
The device should only be used for indoor applications.
The mounting surface must be solid and non-combustible.
Danger of electrical shock/fire hazard/damage to the device due
to incorrect connection
Connect the device only to a power source that complies with SELV
requirements and with the Limited Power Source requirements to EN
60950-1.
3.4 Maintenance
Do not attempt to service or modify this device yourself. Refer this work
to qualified service personnel.
Do not use liquid cleaners or sprays that contain alcohol, spirit or am-
monia.

Safety
© Vanderbilt 2016
7
3.5 Sensor characteristics
The following conditions may be observed when using a CMOS camera. These
are inherent in the design and do not stem from any fault in the camera itself.
Vertical smear:
This phenomenon occurs when viewing a very bright object.
Patterned noise:
This is a fixed pattern, which may appear over the entire monitor screen
when the camera is operated at a high temperature or in a low luminance
environment.
Jagged picture:
When viewing stripes, straight lines, or similar patterns, the image on the
screen may appear jagged.

EU-directives
© Vanderbilt 2016
8
4 EU-directives
This product complies with the requirements of the following European direc-
tives.
The EU declaration of conformity is available to the responsible agencies at:
Vanderbilt
Clonshaugh Business and Technology Park
Clonshaugh
Dublin 17
Ireland
www.vanderbiltindustries.com
European Directive 2004/108/EC „Electromagnetic Compatibility”
Compliance with the European Directive 2004/108/EC has been proven by
testing according to the following standards:
Emitted interference:
EN 55022
Interference resistance:
EN 55024

Technical data
© Vanderbilt 2016
9
5 Technical data
Model
CFMW3025
Type
3 Megapixel IP Indoor Dome Camera
Image Sensor
1/3” AR0330 CMOS
Lens Mount
D19
Lens Type
Motorized 3~9mm
F No
1.2
Angle of View
Wide: 84°(H), 62°(V)
Tele: 30°(H), 22°(V)
Day / Night
Mechanical ICR
Digital Noise Reduction
3D
Minimum Illumination
F:1.2, CL: 0.3 lux@ 50IRE,
B/W: 0.1 lux@ 50IRE, 1/30
Audio In/Out
Audio In/Out
Alarm In/Out
Alarm In*3 / Alarm Out*1
On-board Storage
SD/SDHC slot
Video Compression
H.264 / MJPEG
Video Streaming
Triple streaming
Frame Rate
NTSC: 1080P(1920x1080) @30 fps ;
3M(2048x1536) @15 fps
PAL: 1080P(1920x1080) @25 fps ;
3M(2048x1536) @12 fps
Resolutions
2048x1536(QXGA), 1920x1080(1080P),
1280x720(720P), 720x480(480P),
640x480(VGA), 352x240(CIF),
320x240(QVGA)
Network Protocols
IPv4, HTTP, TCP/IP, RTSP, RTP, RTCP,
ICMP, UDP, IGMP, NTP, SMTP, FTP,
UPnP, DNS, DDNS, DHCP, ARP, SNMP,
IPv6, CIFS, NFS, IEC802.1x, Bonjour
WDR
Digital WDR
Motion Detection
Yes
Privacy Zones
Yes, 4 zones
Users
1 Administrator, 100 Users or Advanced
User
ONVIF
ONVIF compliance test tool pass
Web Browsing Requirements
Internet Explorer IE8 / IE9 / IE10, Firefox
Google chrome,
Connectors
Power In: terminal block/RJ45
Network: RJ-45 connector
Audio in/out: Spring Terminal
Alarm in/out: Spring Terminal
Power Requirement
DC12V(600 mA)
AC24V[450mA(PF=0.5)]
PoE IEEE 802.3af ; Class 0
Operating Temperature
-10°C ~ 50°C

Details for ordering
© Vanderbilt 2016
10
6 Details for ordering
Type
Order No.
Designation
CFMW3025
V54561-C107-
A200
3 Megapixel IP Indoor Dome Camera
Further products and accessories can be found in the internet:
https://is.spiap.com/products/video.html
6.1 Package contents
IP dome camera
Video cable
2 anchors
2 screws
Template
4 GB SD card (in box)
Installation instruction
Utilities CD (including software and documentation)

Camera part and connector definition
© Vanderbilt 2016
11
7 Camera part and connector definition
7.1 Camera part definition
1
Camera base
8
Power supply port
2
Adjusting mechanism
9
Ethernet connector
3
Lens
10
I/O terminal
4
Focal length ring
11
Video output
5
Focus ring
12
Reset button
6
Camera housing
13
SD card
7
Dome cover
14
Default button
7.2 Connector pin definition
7.2.1 Digital I/O terminal
Au.IN
GND
Au.OUT
GND
AI.IN3
AI.IN2
AI.IN1
GND
COM
AI.OUT
Au.IN
Audio in
GND
Au.OUT
Audio out
GND
AI.IN3
Alarm in
AI.IN2
AI.IN1
GND
AI.COM
Alarm out
AI.OUT

Camera part and connector definition
© Vanderbilt 2016
12
7.2.2 Power terminal
Power terminal
DC 12 V / AC 24 V power
terminal
7.2.3 Video out connector
Video Signal Output
Composite video output
7.2.4 Default/Reset buttons
DEFAULT
Return to factory default
by pressing button (after
5 Sec)
RESET
System restart
7.2.5 SD card
SD CARD
SD CARD
To record images when
alarm events happen.

Installing the camera
© Vanderbilt 2016
13
8 Installing the camera
8.1 Precautions
8.1.1 SD memory card
NOTICE
Please install the SD memory card before switching on the camera.
The system cannot detect an SD card that is inserted during operation.
The camera supports SD and SDHC cards.
Physical interface: Part 1. Physical Layer Specification; Version 1.01.
Images may not be recorded or read correctly if an unsupported SD
card is used with the camera.
A SD card can be used for loop recording of images. The life-span
(number of re-writes possible) of a SD card depends on its capacity. For
loop recording, it is recommended to use a large-capacity SD card.
Do not use a card containing the data recorded by another device with
the camera as this may result in the camera not functioning correctly.
Do not modify or overwrite the data, or change the folder name of a SD
card. This may result in the camera not functioning correctly.
Data recorded with the camera does not comply with the image file
format Exif and the DCF standard. If the SD card is to be removed to play
images, use a personal computer for this purpose. Other devices may not
be capable of displaying the images.
Use only new SD cards that were delivered by the manufacturer.
8.1.2 Power supply
Be sure to use only a suitable power adapter. Using the wrong type of power
adapter may cause the camera to malfunction, heat up, or catch fire. Before us-
ing the power adapter, carefully read and observe the Work safety information
and the notes below.
Do not allow the connectors on the power adapter to come into contact
with any other metal objects as this may result in short-circuit.
To connect the power adapter, firmly insert the plug end of the cable in-
to the power terminal. Do not insert the plug into other jacks as this may
cause malfunctioning.
When removing the connection cable, disconnect it by pulling the plug.
Do not pull on the cable.
Do not drop the power adapter or subject it to strong impact.
Do not use the power adapter in hot and humid places.
Temperature increase on the surface of the adapter is normal. Before
moving the adapter to another location, unplug it from the wall outlet, and
wait until its temperature decreases.
Buzzing noises may come from inside. This does not indicate malfunc-
tion.
Using the power adapter near a radio, TV, or cell phone may cause in-
terference. Use the adapter at sufficient distances from these devices.

Installing the camera
© Vanderbilt 2016
14
8.2 Concept of the network camera
The network camera can deliver video images and audio in real time using the
Internet or an intranet. The camera is equipped with Ethernet (RJ-45) 10BASE-
T/100BASE-TX network interfaces.
It can be used in various indoor environments.
Switch
8.3 Setting network camera environment
Items needed for network camera monitoring system
Administrator's personal computer The personal computer that is given
all authorities for setting, operating, monitoring and other functions with the
network cameras is called the "administrator's personal computer" in this
manual.
PC requirements
–Windows Vista , XP, Win7 or Win8 as OS
–Internet Explorer IE 8.0 / IE 9.0 / IE 10.0, Firefox, and Google chrome
–CPU: Intel Pentium 4,2 GHz or higher
–Memory: 1 GB or more
Network camera
Please purchase the appropriate number of cameras required for your ap-
plication.
Connection equipment such as a hub and router suiting the network
system environment, as well as a LAN cable (Cat 5e cable is recommend-
ed).
Camera search application "Webcam IP-Finder" Install this application
from the CD-ROM supplied as an accessory.
1. Double-click "ipfinder_Setup.exe" in the CD-ROM
2. install the application following the instructions on the screen
8.4 Connecting the camera and personal computer via network
IP address
To connect to the network, the administrator needs to set the network camera
IP address. There are two options to set the IP address.
Entering an IP address manually (factory default)
Obtaining an IP address automatically from the DHCP server
Entering the IP address manually.
Your camera is set to this mode at the factory with IP address 192.168.0.10, so

Installing the camera
© Vanderbilt 2016
15
you need to enter this IP address manually to access the camera for the first
time
Obtaining an IP address automatically from the DHCP server
If your network uses a DHCP server, you do not need to change the IP address
of the camera. To activate this function, the option DHCP must be selected in
the "Network/Basic Settings".
The IP address of the network camera can be changed from time to time
when the DHCP server is used. For this reason, it may not be possible to
connect a network camera due to an IP address change if the network cam-
era is accessed using the previously set IP address.
To enable accessing the network camera in this case, a fixed IP address needs
to be assigned manually to the network camera. Make sure to read the instruc-
tion manuals for the network equipment, as well as the manuals for the router,
hub and modem.
To manually select the basic network settings, "Manual" must be selected and
the IP address, subnet mask, default gateway, primary DNS and secondary
DNS have to be entered.
Connection configuration
There are two configuration options for connecting network cameras:
Crossover connection
Connection via a hub, switch, or router
You do not need to assign an IP address to a hub. The default IP address of
your camera is 192.168.0.10. Set the IP address of your personal computer in
the same subnet. (The network segment must be the same segment when
directly connecting using a cross-over cable or connecting via the hub). When
connecting more than one camera, connect the cameras one by one and as-
sign an unused IP address to each one.
You can also use the LAN port of your broadband router. However, when using
the broadband router while the DHCP server function is enabled, turn on the
power after connecting the camera to the router. The camera gets the IP ad-
dress from the router's DHCP server. The IP address will not be 192.168.0.10.
For more information, refer to the user documentation for your computer.
Connecting camera and personal computer
1. Connecting the LAN cable
Connect the LAN cable (straight cable) to the camera and to the hub. Al-
ternatively, connect the camera to a personal computer using the LAN ca-
ble (cross-over cable).
2. Turning Power on
Connect DC12 V /AC 24 V to the power terminal.
Setting the IP address of the personal computer.
Use a free IP address (other than 192.168.0.10, which is the camera's
IP address).
For example, set the IP address to 192.168.0.20 (and the subnet mask
to 255.255.255.0).
For details on the procedure, refer to the user guide for the personal
computer.
Testing the camera connection using ping.
Start a command prompt. Type "ping 192.168.0.10" and press "Enter".
If the "Reply from..." message appears, the connection is correctly es-
tablished.
Search for the camera using the "Webcam IP Manager" and view a camera

Installing the camera
© Vanderbilt 2016
16
image. See Section 6.5.
1. Start "Webcam IP Manager" and click "Search".
2. Check whether the camera name "nwcam05" is displayed in the cam-
era list.
3. Click "nwcam05" to select the camera.
The camera name, IP address and HTTP port number are displayed in
the "Network Camera Lists" field.
4. Double-click the camera you wish to log in to in the camera list.
The screen for entering the user name and password will appear.
5. Enter the administrator log-in ID and password. See "Login dialog".
A camera image screen of the network camera will appear.
To view images without using "Webcam IP Manager," launch the Internet
browser, enter URL http://192.168.0.10/ in the address box and press "EN-
TER."
It takes about 10 seconds to activate the camera.
If a port number other than "80" is set, enter the port number after ":" as in
http://192.168.0.10:88.
8.5 Using the camera search application "Webcam IP Manager"
The "Webcam IP Manager" is an application for searching for network cameras
that can currently be viewed from the administrator's personal computer or a
user's personal computer.
Setting up "Webcam IP Manager"
1. Insert the CD in the CD-ROM drive of the personal computer.
2. Double-click the "ipfinder.Setup" file in the CD-ROM and install
"Webcam IP Manager" in accordance with the instructions on the screen.
IMPORTANT
"Webcam IP Manager" is compatible only with Windows Vista, Windows XP
and Win7. Glitches may occur on your personal computer if it is run with an-
other operating system. Do not install "Webcam IP Manager" with other operat-
ing systems.
Using "Webcam IP Manager" to search for a camera
Set the personal computer to "Administrator authorization" when using
"Webcam IP Manager".
1. Select "Start" > "Programs" > "Webcam IP-Finder".

Installing the camera
© Vanderbilt 2016
17
2. Start "Webcam IP Manager" and click "Search".
All the cameras currently connected to the network will be displayed.
To exit the program, click "Exit".
3. Select the camera you want to log in to in the list of cameras and dou-
ble-click it.
The selected camera name and IP address are displayed in the net-
work camera login fields.
4. Log in to the selected camera as an administrator. (See "Login dialog")
To exit without logging in, click "Exit".
SSDP (Simple Service Discovery Protocol / network protocol)
Prerequisite:
The Web-Cam IP Manager and all devices are located in the same network
segment. If a device and the Web-Cam IP Manager are not located in the same
network segment, you must ensure that the associated gateway (router) pass-
es the SSDP multicast messages sent by the Web-Cam IP Manager on to the
network segment where the device is located.
1. Start the Web-Cam IP Manager by loading IP Manager.exe. This appli-
cation is found on the CD included with delivery.
The Web-Cam IP Manager program window will open:

Installing the camera
© Vanderbilt 2016
18
2. Click "Start".
The Web-Cam IP Manager program window will now display a list of all
the devices available for communication along with their IP and MAC
addresses. Each device's IP address or MAC address is unique.
3. Select the camera whose home page you want to access.
4. Click "Home page of selected device".
The home page of the selected camera will appear. See Section 6.8
Components of the unit home page.
8.6 Login dialog
The content of the following chapters is based on the assumption that Mi-
crosoft Internet Explorer IE 8.0 or higher has been installed.
A person who has logged in as an administrator can perform all functions.
Administrator login
1. Search for the camera using the "Webcam IP-Finder", double-click the
camera you wish to log in to.
The login dialog will appear.
2. Enter the administrator login ID and password in the "Name" and
"Password" fields, respectively and click "Login". The administrator login
ID and password are "admin" and "admin" by default.
The camera image screen will appear.
IMPORTANT
The administrator login allows rewriting of all settings. Make sure to change the
de-fault administrator login ID and password to ensure camera security. Keep
the new administrator login ID and password handy for future use. Information
on how to change the administrator login ID and password can be found in
Section "Access protection.

Installing the camera
© Vanderbilt 2016
19
8.7 Viewing and listening
Images of the network camera can be viewed using the Internet browser of
your personal computer.
Preparations before displaying
Enable cookies
Set "Browser setting when proxy server is used". Change "Security" in the
Internet options as follows.
1. Click "Tools" on Toolbar
2. Click "Internet Options"
3. Select the "Security" tab.
4. Click on "Intranet" if the camera to be operated is inside the intranet,
click on "Internet" if the camera is on the Internet.
5. Click "Level customize."
6. Activate the following radio buttons in the list displayed:
–"Enable" for "ActiveX control and plug in execute"
–"Enable" for "Execution of script of ActiveX control marked safe even
when script is executed"
–"Enable" for "Download of signed ActiveX control "
7. Click "OK."
8. Login to the camera.
Your browser will be launched and the camera login screen will appear.
See Section "Login dialog" for the login method.
When the security warning screen (VeriSign) appears on the first use of
the system, click "Yes."
Administrator authorization is needed to install "Active-X control." Install "Ac-
tive-X control" after changing the personal computer setting to "Administrator
authorization."
Browser settings when proxy server is used
If a proxy server is used, setting the browser to bypass the proxy server during
communication with the network camera is recommended.
1. Launch the browser.
2. Click "Tools" on Toolbar
3. Select "Internet options".
4. Select the "Connect" tab.
5. Click "LAN Setting."
The screen for setting a local area network (LAN) will appear.
If the checkbox "Will use a proxy server" is not marked:
The browser is not set to use a proxy server. Click "Cancel" and quit
setting.
If the checkbox "Will use a proxy server" is marked:
1. Click "Detail setting."
A proxy setup screen will appear.
2. Enter the IP addresses of the network cameras in the fields marked
"Do not use the proxy server with addresses started with the following".
3. Click "OK."
When Windows XP SP2 is used: Click "Install" for "Active-X control."

Installing the camera
© Vanderbilt 2016
20
All browsers except the IE can only be used for image viewing and compres-
sion setting.
A proxy server protected by a firewall sometimes cannot be connected to the
network camera. Consult the network administrator to avoid impacts on net-
work camera operations.
Communication with the network cameras via a proxy server may cause prob-
lems. Install the network cameras after consulting with the network administra-
tor.
If the network cameras are used in conjunction with a proxy server, it may take
some time for the images to be displayed after a login, or the frame rate of the
delivered images may be reduced.
All browsers except the IE only support image viewing and compression set-
ting.
When using Windows XP SP2
If the camera image screen is not displayed, proceed as follows.
1. Select "Pop-up Blocker" on the toolbar.
2. Select "Always Allow Pop-ups from This Site..."
Components of unit home page
OSD: displays camera name, date and time.
Play: shows the live image
Pause: pauses the live image
Speaker: On/Off
Microphone: On/Off
Language: standard setting is English. The website supports 5 different lan-
guages. Image streams 1, 2 & 3: Triple streams 1, 2 & 3 are available for selec-
tion. H.264 & JPEG only support 2 streams when the resolution sets at QXGA
and 1080P.
E-zoom: PTZ control, preset settings and more.