Varytec LED Laser 4 User manual

User’s manual

2 / 7
Table of content
1. Safety instructions........................................................................................................................... 3
2. Working modes...............................................................................................................................4
2.1. Sound to light mode............................................................................................................... 4
2.2. Automatic mode..................................................................................................................... 4
2.3. DMX 512 control .................................................................................................................... 4
2.3.1. DMX channel list............................................................................................................ 5
2.4. Master Slave Mode................................................................................................................ 5
3. Technical data............................................................................................................................ 6

3 / 7
1. Safety instructions
FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperatureAvoid exposing it
to direct rays of the sun or near a heating appliance.
Not put it in a temperature bellow 41°F /5°C, or exceeding 95°F /35°C.
Keep away from humidity, water and dust
Do not place the set in a location with high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
If out of work, contact sales agency immediately
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing,
do not open the cabinet by yourself, it might result a
danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the receptacle, be sure
to hold the plug. When not using the player for an extended period of time
be sure to disconnect the plug from the receptacle.

4 / 7
2. Working modes
- sound to light mode
- automatic mode
- DMX512 mode
- Master slave mode
2.1. Sound to light mode
It runs under Sound Active Mode when dipswitch #9 is on the “ ON ” position and the others are on
the “ OFF ” position . It runs all fancy. And the positions of dipswitches show as picture:
2.2. Automatic mode
It runs under Auto Mode, when all dipswitches are on the “OFF” position. It runs all fancy . And the
positions of dipswitches show as picture:
2.3. DMX 512 control
It runs under DMX512 Control Mode , when dipswitch “ #10” is on the “ ON ” position and dipswitches
“ #1~#9 “ are on the “ ON “ position . Dipswitches “ #1 , #2 , #3 , #4 , #5 , #6 , #7 ,#8 ,#9 “ can choose
the channel address . When dipswitches “ #1 - #9 “ are not all on the “ OFF ” position , the positions of
dipswitches show as picture:

5 / 7
2.3.1. DMX channel list
Channel Value Function Remark
0-119 ON
CH 1 120-255 OFF
CH 2 1-255 Adjust the bright of Red LED(The LED get
more brightness as the value increasing.)
CH 3 1-255 Adjust the bright of Green LED(The LED get
more brightness as the value increasing.)
CH 4 1-255 Adjust the bright of Blue LED(The LED get
more brightness as the value increasing.)
When the value of
channel 5 is “0”
0 Adjust the brightness.
CH 5 1-255 Choosing the fancy. 37 fancy
CH 6 1-255 Adjust the speed of fresh(The speed getting
more faster as the value increasing.)
Suggestion : The LED should not be lighted over 10 second, during the dimmer mode,
2.4. Master Slave Mode
1. The master runs as the dipswitches “ #1,#2,#3~8,#10 “ are on the “ OFF “ position . And the
positions of dipswitches show as picture:
2. The slave runs as any dipswitch in “#1~#8” is on the “ON” position. And the positions of
dipswitches show as picture
3. It runs under Sound Active Mode when dipswitch #9 is on the “ ON ” position. And the
positions of dipswitches show as picture:

6 / 7
4. The master and the slave connecting by the DMX signal cable (Remark : you can connect
slaves to master as many as you want . And each cable should not over 5 meter . ) Show as
picture :
3. Technical data
LED 5mm low power LED red green blue 256pcs
Power supply AC240V/50Hz
Power consumption Max 45W
Measurements (L x W x H) 935 x 155 x 195mm
Weight 6,7kg

7 / 7
Importeur:
B & K Braun GmbH
Industriestraße 1
D-76307 Karlsbad
www.bkbraun.com
[email protected]