Varytec LED PAD 147 User manual

User manual
LED PAD 147

2 / 8
Table of contents
1. Safety instructions............................................................................................................................ 3
1.1. FOR SAFE AND EFFICIENT OPERATION............................................................................ 3
2. Technical Data ................................................................................................................................. 4
3. Operation.......................................................................................................................................... 4
3.1. DMX Control............................................................................................................................ 4
3.2. Automatic mode....................................................................................................................... 6
3.3. Sound to Light mode ............................................................................................................... 6
3.4. Set up your fixed colour........................................................................................................... 6
3.5. Master Slave mode.................................................................................................................. 6
4. DMX Cable info................................................................................................................................ 7

3 / 8
1. Safety instructions
•This device is suitable for indoor use only.
•All modifications to the device will void the warranty.
•Repairs are to carry out by skilled personnel only.
•Use only fuses of the same type and original parts as spare parts.
•Protect the unit from rain and humidity to avoid fire and electric shocks.
•Make sure to unplug the power supply before opening the housing.
1.1.FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature
Avoid exposing it to direct rays of the sun or near a heating appliance.
Not put it in a temperature bellow 32°F / 0°C, or e xceeding 104°F / 40°C.
Keep away from humidity, water and dust
Do not place the set in a location with high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
If out of work, contact sales agency immediately
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing,
do not open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the receptacle, be sure
to hold the plug. When not using the device for an extended period of time, be sure to
disconnect the plug from the receptacle
.

4 / 8
Important: Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or
problems. Make sure the electrical connection is carried out by qualified
personnel. All electrical and mechanical connections have to be carried out
according to the European safety standards.
2. Technical Data
Power supply
100
-
240V
50
/60
Hz
Power consumption
15
W
Current
0.
1
A
ound
to Light
Via
built in mic
DMX512
connection
3 Pin XLR
Weight
2,
1
Kg
Measurements
273 x 265 x 79
m
m
Maximum ambient temperatur
e
-
20
°
-
+40°
C
Maximum housing temperature
+20
°
-
+60°
C
Fuse
F1A, 250V
Channel
6
Number of LEDs
147 x 10mm
LEDs
(51R, 48G, 48
B)
Beam angle
25
°
3. Operation
3.1.DMX Control
To set up your desired DMX address, you have to set up the dipswitch on the backside as follows:
- Set the dip 10 to OFF
- With all the other dipswitches 1 to 9 you can set up the DMX address regarding the binary
system. In this system each dip has a value, which you have to add to get the dmx address.
Dip 1 2 3 4 5 6 7 8 9
Wert 1 2 4 8 16 32 64 128 256
If you want to set the address 10 then you have to setthe dips 4 and 2 to ON, because theire
values are 2 and 8 and 2+8=10.
Remember that the item needs 6 channels.
So if you want to set the first item to address 1, the second item has to be minimum address 7,
because 1+6=7.

5 / 8
DMX
Channel
Value
Fun
c
tion
1
0
-
255
Dimmer 0
-
100%
2
0
–
255
Dimmer f
o
r R
ed
0
–
100 %
3
0
–
255
Dimmer f
o
r G
ree
n 0
–
100%
4
0
–
255
Dimmer f
o
r Bl
u
e
0
–
100 %
5
0
–
255
trobe slow to fast
6
0
–
9
10 – 19
20 – 29
30 – 39
40 – 49
50 – 59
60 – 69
70 – 79
80 – 89
90 – 99
100 – 109
110 – 119
120 – 129
130 – 139
140 – 149
150 – 159
160 – 169
170 – 179
180 – 189
190 – 199
200 – 209
210 – 219
220 – 229
230 – 239
240 – 249
250 – 255
N
o
function
cene R – G – B
cene R – RG – GB
cene R – RB – G
cene G – B – R
cene G – RG – B
cene G – RB – RG
cene B – G – R
cene B – GB – RB
cene B – BR – RG
cene RG – GB – RB
cene RB – GB – RG
cene RB – R – RG
cene GB – B – R
Auto 1 Color fade
Auto 2 Ramp down
Auto 3 Ramp up
Auto 4 strobe slow to fast
Auto 5 colour synch strobe
Auto 6 colour change different speeds
Auto 7 asynch trobe
Auto 8 Auto loop
ound 1 colour change
ound 2 Colou Flash
ound 3 Colour Flash with white
ound 4 Colour Flash with Brightness
Attention!! If the channel 6 is between value 1 and 9 the item is controlled as described above. If the
value of channel 6 is higher then it is controlled as follows:
DMX
channel
V
alue
Fun
c
tion
1
0
-
255
Dimmer 0
-
100%
2
0
–
255
Dimmer f
o
r R
ed
0
–
100 %
3
0
–
255
SPEED
A
ND
FADE
TIM
ES
DEPENDING ON
Program
4
0
–
255
Run
time
from
0 5
till
5 5min
5
0
–
255
trobe
slow to fast
6
0
-
255
Auto Modes

6 / 8
3.2.Automatic mode.
To set up the automatic mode, do as follows:
- Set the dips 9 and 10 to ON
- Set the dip 8 to OFF
- With the dips 1, 2, 3 you can adjust the speed
- With the dips 4, 5, 6 you can choose the automaticprogram.
3.3.Sound to Light mode
to choose the sound to light mode, go on as you read here:
- Set the dips 8 and 10 to ON
- Set the dip 9 to OFF
- With the dips 4, 5, 6 you can choose the soundprogram
3.4.Set up your fixed colour
To set up own fixed colours go on as follows:
- Set the dip 10 to ON
- With the dips 1 and 2 you can adjust the dimmer.
- With the dips 3 and 4 you can adjust the strobe
- With the dips 5, 6, 7 you can choose red, green and blue
3.5.Master Slave mode
If you want to set up a master slave mode, first you have to connect all the fixtures.
For the connection of master fixture and slave fixture, please use a standard dmx 3 pole XLR 110
Ohms cable. Connect the male connector to the master and the female connector to the slave
fixture. Go on like this until all the fixtures you want to be connected, are connected. The
possible settings for the master are the Automatic mode or the own colour mode. All the other
fixtures (slave) you have to set up as follows:
- et all dips to OFF

7 / 8
4. DMX Cable info

8 / 8
Importer:
B & K Braun GmbH
Industriestraße 1
D-76307 Karlsbad
www.bkbraun.com
[e-mail]