Varytec LED ROAD PAR 14 x 3W RGB 3in1 User manual

User’s manual
LED ROAD PAR
14 x 3W RGB 3in1

2 / 13
Table of contents
1. Safety instructions............................................................................................................................ 3
1.1. FOR SAFE AND EFFICIENT OPERATION............................................................................ 3
2. General information.......................................................................................................................... 4
3. Product overview.............................................................................................................................. 5
4. Structure of the menu....................................................................................................................... 6
4.1 Overview........................................................................................................................................ 6
4.2 Settings.......................................................................................................................................... 7
4.2.1 Static Color.............................................................................................................................. 7
4.2.2 Auto-mode............................................................................................................................... 7
4.2.3 RUN......................................................................................................................................... 7
4.2.4 DMX ........................................................................................................................................ 7
4.2.5 Personality............................................................................................................................... 7
4.2.6 ID-address............................................................................................................................... 8
4.2.7 Edit Custom............................................................................................................................. 8
4.2.8 Setting ..................................................................................................................................... 8
4.2.9 CAL1 ....................................................................................................................................... 9
4.2.10 CAL2 ..................................................................................................................................... 9
4.2.11 KEYLOCK ............................................................................................................................. 9
5. DMX-Table....................................................................................................................................... 9
6. Technical Data ............................................................................................................................... 12

3 / 13
1. Safety instructions
•This device is suitable for indoor use only.
•All modifications to the device will void the warranty.
•Repairs are to carry out by skilled personnel only.
•Use only fuses of the same type and original parts as spare parts.
•Protect the unit from rain and humidity to avoid fire and electric shocks.
•Make sure to unplug the power supply before opening the housing.
1.1.FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature
Avoid exposing it to direct rays of the sun or near a heating appliance.
Not put it in a temperature bellow 32°F /0°C, or exceeding 104°F /40°C.
Keep away from humidity, water and dust
Do not place the set in a location with high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
If out of work, contact sales agency immediately
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing,
do not open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug.
When not using the device for an extended period of time, be sure to disconnect the plug
from the receptacle
.

4 / 13
Important: Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or problems. Make sure
the electrical connection is carried out by qualified personnel. All electrical and mechanical
connections have to be carried out according to the European safety standards.
2. General information
Fixtures: 1 x Led Road PAR
1 x Power cable
1 x DMX cable
1 x User manual
Unpacking:
Thank you for purchasing the LED Par 18x8W RGBW IP65. Every device has been thoroughly tested
and has been transported in perfect operation condition. Carefully check the carton for damage that
may occur during transporting. If the carton appears to be damaged, carefully inspect your fixture for
any damage and be sure all accessories necessary to operate the unit has arrived intact. Carefully
unpack the carton, check the contents to ensure that all parts are present, and have been received in
good condition.
AC Power
The fixture has an auto-switching power supply that can accommodate a wide range of input voltages.
The only thing necessary to do before powering on the unit is to make sure the line voltage you are
applying is within the range of accepted voltages. This fixture will accommodate between 100V and
240V AC 50-60Hz. All fixtures must be powered directly to a switches circuit and cannot be run with a
rheostat (variable resistor or dimmer circuit, even if the rheostat or dimmer channel is used solely for
0% to 100% switch).

5 / 13
3. Product overview
Control board
All fixture functions and settings are accessible via the built-in control panel interface.

6 / 13
4. Structure of the menu
4.1 Overview

7 / 13
4.2 Settings
4.2.1 Static Color
Combine red, green and blue (0-255) to create an infinite range of color.
With the menu point S (0-20) you can set the speed of the strobe.
4.2.2 Auto-mode
Choose [AUTO] and press [ENTER].
The programs [AT.01] to [AT.10] are saved and it is not possible to change them with [EDIT]
The programs [PR.01] to [PR.10] are recorded, but you can change them with [EDIT].
4.2.3 RUN
Enter the [RUN] mode to set a working mode.
Choose [dMX] for DMX mode.
Choose [SLA] for Master Slave mode
4.2.4 DMX
Adjusts the DMX address (1-512) of the device.
4.2.5 Personality
Enter the [PERSONALITY] mode to select between the DMX modes: [STAG], [Arc.1], [Ar1.d], [Arc.2],
[Ar2.d], [Ar2.s] or [HSV]

8 / 13
4.2.6 ID-address
Enter the [Id] mode to set the ID-address of the device.
4.2.7 Edit Custom
Here you can change the programs [PR.01] to [PR.10.
Each custom program has 30 steps that can be edited.
Each step allows creation of a scene using: Red, Green, Blue, White, Strobe, Time, and Fade.
Press ENTER for 5 seconds to store your settings.
4.2.8 Setting
Select [UPLD] to upload the custom programs from the current Master unit to the Slave units. In order
to activate the upload function the password must be entered: ([UP] + [DOWN] + [UP] + [DOWN])
Confirm with ENTER.
When uploading the Slave units will display yellow. If an error occurs when uploading the Slave units
will display red. On successful uploading of the custom programs the Slave units will display green. In
order to reset custom modes to default values select [REST].
Enter [ID] in order to allow/disallow ID address function from DMX512 controller.
If you choose in [RGBW] mode the option [YES], an internal white balance is adjusted to get a
harmonious white. If you choose [NO] all colors are driven with 100%.
The RGBW parameters can be set in [CAL2] menu.
Enter [POW] to set the power consumption. The power consumption is 25W if you choose [NORM]-
mode and 50W in [HIGH]-mode.
Enter [DIM] mode to select dimmer mode and dimmer speed. When dimmer mode is set to [OFF] the
behavior of dimming is linear. Dim 1, 2, 3, 4 are dimmer with different speed, dim 4 is the slowest. The
settings in [DIM] mode do not react to the [STAG] mode.

9 / 13
4.2.9 CAL1
Enter [CAL1mode to select white color of different color temperature.
There are 11 pre-programmed white colors can be edited by using [Red], [Green], [Blue], [White].
4.2.10 CAL2
Enter [CAL2] mode to adjust the RGB parameter to make different whites.
When the new setting is activated, the DMX controller choose RGB = 255, 255, 255, the white color
will be made by the actual RGB values on the [CAL2].
4.2.11 KEYLOCK
Enter [KEY] mode to activate or deactivate the key lock. .
Press [ENTER] to enter the password.
Password: [UP] + [DOWN] + [UP] + [DOWN].
5. DMX-Table
The device has 6 DMX modes.

10 / 13