Varytec RGBW IP65 User manual

Manual
LED Pixel Street Bar
12x15W RGBW IP65

2 / 20
Table of contents
1. Safety instructions............................................................................................................................ 3
1.1. For safe and efficient operation...............................................................................................3
2. Designated use ................................................................................................................................ 4
2.1. Overhead installation............................................................................................................... 5
3. Introduction....................................................................................................................................... 7
3.1. Product overview..................................................................................................................... 7
3.2. Dimension................................................................................................................................ 8
4. Connections ..................................................................................................................................... 9
4.1. Electrical connections.............................................................................................................. 9
4.2. DMX connections .................................................................................................................... 9
4.3. DMX connection with terminator.............................................................................................. 9
5. Control............................................................................................................................................ 10
5.1. Structure of the menu............................................................................................................ 10
6. DMX chart ...................................................................................................................................... 12
6.1. DMX mode 1 (3 channels).....................................................................................................12
6.2. DMX mode 2 (4 channel).......................................................................................................12
6.3. DMX mode 3 (5 channels).....................................................................................................12
6.4. DMX mode 4 (8 channels).....................................................................................................12
6.5. DMX mode 5 (11 channels)...................................................................................................14
6.6. DMX mode 6 (59 channels)...................................................................................................16
7. Photometrical data ......................................................................................................................... 19
8. Technical data................................................................................................................................ 19

1. Safety instructions
•This
device is suitable for indoor and outdoor use.
•
All modifications to the device will void the warranty.
•
Repairs are
•
Use only fuses of the same type and original parts as spare parts.
•
Make sure to unplug the power supply before opening the housing.
1.1.
For safe and efficient operation
Be careful with heat and extreme temperature
Avoi
d exposing it to direct rays of the sun or near a heating appliance.
Not put it in a temperature bellow 32
To avoid placing on un-
stable location
Select a level and stable location to avoid vibration.
Do not use
chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt. Before cleaning unplug
the device.
If out of work, contact sales agency immediately
Any troubles arose, remove the power plug soo
open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. Whe
using the device for an extended period of time, be sure to disconnect the plug from the receptacle.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resultin
connection is carried out by qualified personnel. All electrical and mechanical connections
have to be carried out according to the European safety standards.
3 / 20
device is suitable for indoor and outdoor use.
All modifications to the device will void the warranty.
Repairs are
to carry out by skilled personnel only.
Use only fuses of the same type and original parts as spare parts.
Make sure to unplug the power supply before opening the housing.
For safe and efficient operation
Be careful with heat and extreme temperature
d exposing it to direct rays of the sun or near a heating appliance.
Not put it in a temperature bellow 32
°F /0°C, or exceeding 104°F /40°C.
stable location
Select a level and stable location to avoid vibration.
chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt. Before cleaning unplug
If out of work, contact sales agency immediately
Any troubles arose, remove the power plug soo
n, and contact with an engineer for repairing, do not
open the cabinet by yourself, it might result a danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. Whe
using the device for an extended period of time, be sure to disconnect the plug from the receptacle.
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resultin
g defects or problems. Make sure the electrical
connection is carried out by qualified personnel. All electrical and mechanical connections
have to be carried out according to the European safety standards.
Use only fuses of the same type and original parts as spare parts.
Make sure to unplug the power supply before opening the housing.
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt. Before cleaning unplug
n, and contact with an engineer for repairing, do not
Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. Whe
n not
using the device for an extended period of time, be sure to disconnect the plug from the receptacle.
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
g defects or problems. Make sure the electrical
connection is carried out by qualified personnel. All electrical and mechanical connections

4 / 20
2. Designated use
This device was developed for professional use on stages, in discos, theatres etc. The device is only
approved for a connection up to 230V 50/60 Hz AC voltage and for indoor and outdoor use.
Regular breaks during operation increase the lifetime of your device.
Avoid convulsions or any form of forceful impact during the installation or the start-up of the device.
Take care that no cables are lying around. You would endanger your own safety and also the safety of
a third party.
If you use fog devices make sure that the saturation of the fog has to enable a visibility of at least 10m.
Operate the device not during thunderstorms. Surge voltages could destroy the device. Unplug the
power supply during thunderstorms.
During the installation the use of the mounting bracket is obligatory.
Surrounding objects or surfaces should not be in contact with the device.
Make sure that during the installation and removal of the device the area below the place of
installation is basically cordoned off. This also applies to implementation of service.
The device has basically been protected by a suitable safety.
Make familiar yourself with the functions of the device before start-up. People without the experience
should not handle with the device. The most cause of functional disorder is inappropriate handling.
Do not use chemicals or volatile liquids for cleaning. Use a clean dry cloth to wipe off the dust, or a
wet soft cloth for stubborn dirt.
For transport use the original packing or designated accessory to avoid damages during the transport.
For reasons of safety unauthorized changes are forbidden.
A usage of the device which differs from usages which are described in this manual can cause
damages of the device. In that case the warranty expires. Additional you should notice that every
differed usage is related with dangers and can cause e.g. an electrical short, fire, electric shock or
crash.

2.1.
Overhead installation
Danger of life!
You have to observe the regulations of BGV C1 (formerly VBG 70) and
EN60598-2-
17
The suspension devices have to be build and measured so they can withstand for an hour the tenfold
of the payload without suffering a permanent detrimental deformation.
Basically installation has to be made by using
suitable net. The second suspension must be designed and attached so no part of the installation can
fall down in case of failure.
During construction, reconstruction and deconstruction unnecessary stay in
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden.
The operator is obliged to following safety
- Before the first start-
up or after critical changes be
expert.
-
Review in the frame of the inspection test at least all four years by an expert. .
-
Review by a qualified person at least once a year.
How to carry out the overhead installation:
In tidal fall you should
install the device out of the lounge area of people
IMPORTANT!
Overhead installation requires a high level of experience. This includes knowledge of
calculating the payload, used installation material and safety inspections of the used material and the
p
rojector whereas the required experience is not limited to this. Do not try to carry out installation
yourself under any circumstances if you are not qualified. Contact a professional installer. An
inappropriate installation can lead to injuries and/or dam
It is not allowed to install the device in the grip area of people.
If the device may hang from the ceiling or from high beams, the use of truss systems is mandatory.
The device may not be installed so it can swing freely in the room.
Please note: Crashing down items can cause serious injuries! Do not install the projector, if you doubt
the safety of a possible installation form!
Before installation make sure that the mounting surface has the ability to carry the tenfold point load of
the own weight of the device.
Mount the device with the mounting
During overhead installation the device must be always secured by a safety rope which is designed to
hold the twelvefold weight
of device. Only safety ropes with quick
may be used. Hang up the safety rope in the hole of the mounting bracket. Direct the rope over the
truss or an appropriate fastening point. Hang up the end in the fastening element a
locking nut. A safety rope once exposed to failing load or damaged may not be used furthermore.
5 / 20
Overhead installation
Danger of life!
You have to observe the regulations of BGV C1 (formerly VBG 70) and
17
Installations are to
carry out by skilled personnel only.
The suspension devices have to be build and measured so they can withstand for an hour the tenfold
of the payload without suffering a permanent detrimental deformation.
Basically installation has to be made by using
a second separate suspension. This can be e.g. a
suitable net. The second suspension must be designed and attached so no part of the installation can
During construction, reconstruction and deconstruction unnecessary stay in
the range of moving
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden.
The operator is obliged to following safety
-related and mechanical facilities:
up or after critical changes be
fore restarting it has to be checked by an
Review in the frame of the inspection test at least all four years by an expert. .
Review by a qualified person at least once a year.
How to carry out the overhead installation:
install the device out of the lounge area of people
Overhead installation requires a high level of experience. This includes knowledge of
calculating the payload, used installation material and safety inspections of the used material and the
rojector whereas the required experience is not limited to this. Do not try to carry out installation
yourself under any circumstances if you are not qualified. Contact a professional installer. An
inappropriate installation can lead to injuries and/or dam
aged properties.
It is not allowed to install the device in the grip area of people.
If the device may hang from the ceiling or from high beams, the use of truss systems is mandatory.
The device may not be installed so it can swing freely in the room.
Please note: Crashing down items can cause serious injuries! Do not install the projector, if you doubt
the safety of a possible installation form!
Before installation make sure that the mounting surface has the ability to carry the tenfold point load of
Mount the device with the mounting
-
bracket to your trussing system using an appropriate clamp.
During overhead installation the device must be always secured by a safety rope which is designed to
of device. Only safety ropes with quick
-
release safety fastener elements
may be used. Hang up the safety rope in the hole of the mounting bracket. Direct the rope over the
truss or an appropriate fastening point. Hang up the end in the fastening element a
locking nut. A safety rope once exposed to failing load or damaged may not be used furthermore.
You have to observe the regulations of BGV C1 (formerly VBG 70) and
carry out by skilled personnel only.
The suspension devices have to be build and measured so they can withstand for an hour the tenfold
a second separate suspension. This can be e.g. a
suitable net. The second suspension must be designed and attached so no part of the installation can
the range of moving
areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden.
fore restarting it has to be checked by an
Review in the frame of the inspection test at least all four years by an expert. .
Overhead installation requires a high level of experience. This includes knowledge of
calculating the payload, used installation material and safety inspections of the used material and the
rojector whereas the required experience is not limited to this. Do not try to carry out installation
yourself under any circumstances if you are not qualified. Contact a professional installer. An
If the device may hang from the ceiling or from high beams, the use of truss systems is mandatory.
Please note: Crashing down items can cause serious injuries! Do not install the projector, if you doubt
Before installation make sure that the mounting surface has the ability to carry the tenfold point load of
bracket to your trussing system using an appropriate clamp.
During overhead installation the device must be always secured by a safety rope which is designed to
release safety fastener elements
may be used. Hang up the safety rope in the hole of the mounting bracket. Direct the rope over the
truss or an appropriate fastening point. Hang up the end in the fastening element a
nd tie up the
locking nut. A safety rope once exposed to failing load or damaged may not be used furthermore.

6 / 20
The maximum drop exceed must not exceed 20cm.
A safety rope once exposed to failing load or damaged may not be used furthermore.
Adjust the desired inclination angle via the mounting bracket and tighten the screw.

7 / 20
3. Introduction
Thank you for buying the LED Pixel Street Bar 12x15W RGBW IP65. It is a powerful device.
For a successful installation and operation, please read this manual carefully.
3.1.Product overview

8 / 20
3.2.Dimension

9 / 20
4. Connections
4.1.Electrical connections
If you wish to change the power supply settings, see the chapter Appendix. Connect the fixture to the
mains with the enclosed power cable and plug. The earth has to be connected.
Cable (EU) Cable (US) Pin International
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
4.2.DMX connections
To make a DMX512 connection go ahead like it is described in the picture. Make sure that you use
shielded cable. 3pole or 5pole XLR cables are suitable. If you use a controller with a 5 pin DMX output
connector, you will need to use a 5pin to 3 pin adapter.
4.3.DMX connection with terminator
Where the DMX cable has to run a long distance or the equipment is operated in an electrically noisy
environment like a disco for installations, we recommend using a DMX terminator. This prevents
corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR
connector with a 120 Ωresistor between pins 2 and 3, which is then plugged into the XLR output
socket of the last device in the series. Please look to the bottom drawings.

10 / 20
5. Control
Press MENU to reach the first menu and use UP/DOWN to get to submenu. To open submenu you
have to press ENTER, here you can also reach other menu items with UP/DOWN buttons, confirm
with ENTER. Press MENU to store your settings.
5.1.Structure of the menu
Menu Submenu 1 Submenu 2 Submenu 3 Function
PROGRAM P: 1 – 20
S:031 Here you can choose one of 20
automatic programs (AUTO is loop
through all programs) and set the
speed for the automatic programs
CUSTOM 1 – 12 Choose one customer program
DMXSETUP
CH03 A: 1 – 512
Choose a DMX mode and set the
DMX address
CH04
CH05
CH08
CH11
CH59
COLORSET
RED 0 – 255 Dimmer red 0 – 100%
GRE 0 – 255 Dimmer green 0 – 100%
BLU 0 – 255 Dimmer blue 0 – 100%
WHI 0 – 255 Dimmer white 0 – 100%
SETUPDIM 0 – 255 Dimmer 0 – 100%
WHITE 11 W01 – W11
Set one of 11 customer whites
R: 0 – 255 Dimmer red 0 – 100%
G: 0 – 255 Dimmer green 0 – 100%
B: 0 – 255 Dimmer blue 0 – 100%
W: 0 – 255 Dimmer white 0 – 100%
SETUP ID OFF Deactivates the fixture ID
1 – 66 Set the fixture ID
COLOR 01 – 52 Choose one 52 preset colors.
CUSTOM 12 PROG01 – PROG12 EDT
Sce01
LED 01 –
LED 12
Set 12 customer programs
STRO 01 –
STRO 20
FADE 00 –
FADE 99
TIME 00 –
TIME 99
UPLOAD PASSWORD
With this function you can upload
the customer programs via DMX to
another device. For this you need
to enter a password (DOWN + UP
+ DOWN + UP)
DMX SIGN FREEZE If the DMX signal fails the last DMX
value is hold.
BLACKOUT If the DMX signal fails the device

11 / 20
blackouts
RUN MODE SLAVE The device acts as slave. DMX Activates the DMX mode.
LED_SENS No function
SET UPDIS On / Off (De-)Activates the backlight of the
display.
KEY LOCK 10s (De-)Activates the key lock after 20s and 30s. To unlock you have to
enter a password (UP/DOWN).
30s
Off
MASTER On / Off (De-)Activates the master function.
SETUPCUR LINE Setting the dimming mode.
OPTIMIZE
VERSION Shows the current software version.
DOWNLOAD
PCB TEMP Shows the current PCB
temperature.
UPDATE Update
RESET Reset

12 / 20
6. DMX chart
6.1.DMX mode 1 (3 channels)
Channel Value from Value to Function
1 0 255 Hue
2 0 255 Saturation
3 0 255 Brightness
6.2.DMX mode 2 (4 channel)
Channel Value from Value to Function
1 0 255 Dimmer red LEDs 0 – 100%
2 0 255 Dimmer green LEDs 0 – 100%
3 0 255 Dimmer blue LEDs 0 – 100%
4 0 255 Dimmer white LEDs 0 – 100%
6.3.DMX mode 3 (5 channels)
Channel Value from Value to Function
1 0 255 Dimmer 0 – 100%
2 0 255 Dimmer red LEDs 0 – 100%
3 0 255 Dimmer green LEDs 0 – 100%
4 0 255 Dimmer blue LEDs 0 – 100%
5 0 255 Dimmer white LEDs 0 – 100%
6.4.DMX mode 4 (8 channels)
Channel Value from Value to Function
1 0 255 Dimmer 0 – 100%
2 0 255 Dimmer red LEDs 0 – 100%
3 0 255 Dimmer green LEDs 0 – 100%
4 0 255 Dimmer blue LEDs 0 – 100%
5 0 255 Dimmer white LEDs 0 – 100%
6
0 19 No function
20 23 Red
24 27 Green
28 31 Blue
32 35 Yellow
36 39 Cyan
40 43 Magenta
44 47 White
48 51 Orange
52 55 Pink
56 59 Violet
60 63 Aquamarine
64 67 Sky blue
68 71 Full white

13 / 20
72 75 Cool white
76 79 Warm white
80 83 White 3200
84 87 White 2500
88 91 Yellow 2
92 95 Straw
96 99 Orange 2
100 103 Light rose
104 107 Dark pink
108 111 Magenta 2
112 115 Blue 2
116 119 Med blue green
120 123 Dark blue
124 127 Bright pink
128 131 Medium blue
132 135 Golden amber
136 139 Deep golden amber
140 143 Pale lavender
144 147 Apricot
148 151 Dark lavender
152 155 Chocolate
156 159 Just blue
160 163 Surprise pink
164 167 Scarlet
168 171 Surprise peach
172 175 Fire
176 179 English rose
180 183 Mauve
184 187 Bright blue
188 191 Alice blue
192 195 Rose indigo
196 199 Urban blue
200 203 Cool blue
204 207 Light salmon
208 211 Mayan sun
212 215 Cherry rose
216 219 Flesh pink
220 223 Skelton exotic sangria
224 255 Amber
7 0 No function
1 255 36 Color macros
8 0 255 Strobe slow - fast

14 / 20
6.5.DMX mode 5 (11 channels)
Channel Value from Value to Function
1 0 255 Dimmer 0 – 100%
2 0 255 Dimmer red LEDs 0 – 100%
3 0 255 Dimmer green LEDs 0 – 100%
4 0 255 Dimmer blue LEDs 0 – 100%
5 0 255 Dimmer white LEDs 0 – 100%
6
0 10 No function
11 20 R100% / G upwards / B0% / W0%
21 30 R downwards / G100% / B0% / W0%
31 40 R 0% / G100% / B upwards / W0%
41 50 R upwards / G downwards / B100% / W0%
51 60 R upwards / G0% / B100% / W0%
61 70 R100% / G0% / B downwards / W0%
71 80 R100% / G0% / B0% / W downwards
81 90 R100% / G0% / B0% / W downwards
91 100 R upwards / G downwards / B0% / W0% 
R downwards / G upwards / B0% / W0%
101 110 R upwards / G0% / B downwards / W0% 
R downwards / G0% / B upwards / W0%
111 120 R0% / G upwards / B downwards / W0% 
R0% / G upwards / B downwards / W0%
121 130 R upwards / G upwards / B downwards / W0% 
R downwards / G downwards / B upwards / W0%
131 140 R upwards / G downwards / B downwards / W0%
R downwards / G upwards / B upwards / W0%
141 150 R upwards / G downwards / B upwards / W0%  R downwards / G upwards / B downwards / W
upwards
151 160 R upwards / G0% / B downwards / W0%  R downwards / G upwards / B0% / W0% 
R0% / G downwards / B upwards / W0%
161 170
R upwards / G100% / B downwards / W0% 
R100% / G downwards / B upwards / W0% 
R downwards / G upwards / B100% / W0% 
R downwards / G upwards / B0% / W0% 
R0% / G downwards / B upwards / W0% 
R0% / G0% / B downwards / W upwards
171 180 R upwards / G0% / B0% / W downwards  R0% / G100% / B downwards / W0% 
R upwards / G100% / B0% / W0%
181 190
R100% / G downwards / B0% / W0% 
R100% / G0% / B upwards / W0% 
R downwards / G0% / B100% / W0% 
R0% / G upwards / B100% / W0%
191 200 RGBW
201 205 Customer White 1
206 210 Customer White 2

15 / 20
211 215 Customer White 3
216 220 Customer White 4
221 225 Customer White 5
226 230 Customer White 6
231 235 Customer White 7
236 240 Customer White 8
241 245 Customer White 9
246 250 Customer White 10
251 255 Customer White 11
7 0 255 Speed for channel 6 0 15 No function
16 255 Strobe slow – fast
8
0 No function
2 10 Automatic program 1
11 20 Automatic program 2
21 30 Automatic program 3
31 40 Automatic program 4
41 50 Automatic program 5
51 60 Automatic program 6
61 70 Automatic program 7
71 80 Automatic program 8
81 90 Automatic program 9
91 100 Customer program 1
101 110 Customer program 2
111 120 Customer program 3
121 130 Customer program 4
131 140 Customer program 5
141 150 Customer program 6
151 160 Customer program 7
161 170 Customer program 8
171 180 Customer program 9
181 190 Customer program 10
191 200 Customer program 11
201 255 Customer program 12
9 0 255 Speed for channel 8
10 0 127 Dimmer speed off
128 255 Dimmer speed
11
0 – 9 All IDs 210 ID 21 233 ID 44
10 – 19 ID 1 211 ID 22 234 ID 45
20 – 29 ID 2 212 ID 23 235 ID 46
30 – 39 ID 3 213 ID 24 236 ID 47
40 – 49 ID 4 214 ID 25 237 ID 48
50 – 59 ID 5 215 ID 26 238 ID 49
60 – 69 ID 6 216 ID 27 239 ID 50
70 – 79 ID 7 217 ID 28 240 ID 51
80 – 89 ID 8 218 ID 29 241 ID 52

16 / 20
90 – 99 ID 9 219 ID 30 242 ID 53
100 – 109 ID 10 220 ID 31 243 ID 54
110 – 119 ID 11 221 ID 32 244 ID 55
120 – 129 ID 12 222 ID 33 245 ID 56
130 – 139 ID 13 223 ID 34 246 ID 57
140 – 149 ID 14 224 ID 35 247 ID 58
150 – 159 ID 15 225 ID 36 248 ID 59
160 – 169 ID 16 226 ID 37 249 ID 60
170 – 179 ID 17 227 ID 38 250 ID 61
180 – 189 ID 18 228 ID 39 251 ID 62
190 – 199 ID 19 229 ID 40 252 ID 63
200 – 209 ID 20 230 ID 41 253 ID 64
231 ID 42 254 ID 65
232 ID 43 255 ID 66
6.6.DMX mode 6 (59 channels)
Channel Value from Value to Function
1 0 255 Dimmer 0 – 100%
2 0 255 Dimmer red LEDs 0 – 100%
3 0 255 Dimmer green LEDs 0 – 100%
4 0 255 Dimmer blue LEDs 0 – 100%
5 0 255 Dimmer white LEDs 0 – 100%
6 0 127 Dimmer speed off
128 255 Dimmer speed
7
0 10 No function
11 20 R100% / G upwards / B0% / W0%
21 30 R downwards / G100% / B0% / W0%
31 40 R 0% / G100% / B upwards / W0%
41 50 R upwards / G downwards / B100% / W0%
51 60 R upwards / G0% / B100% / W0%
61 70 R100% / G0% / B downwards / W0%
71 80 R100% / G0% / B0% / W downwards
81 90 R100% / G0% / B0% / W downwards
91 100 R upwards / G downwards / B0% / W0% 
R downwards / G upwards / B0% / W0%
101 110 R upwards / G0% / B downwards / W0% 
R downwards / G0% / B upwards / W0%
111 120 R0% / G upwards / B downwards / W0% 
R0% / G upwards / B downwards / W0%
121 130 R upwards / G upwards / B downwards / W0% 
R downwards / G downwards / B upwards / W0%
131 140 R upwards / G downwards / B downwards / W0%

R downwards / G upwards / B upwards / W0%
141 150 R upwards / G downwards / B upwards / W0% 
R downwards / G upwards / B downwards / W

17 / 20
upwards
151 160 R upwards / G0% / B downwards / W0%  R downwards / G upwards / B0% / W0% 
R0% / G downwards / B upwards / W0%
161 170
R upwards / G100% / B downwards / W0% 
R100% / G downwards / B upwards / W0% 
R downwards / G upwards / B100% / W0% 
R downwards / G upwards / B0% / W0% 
R0% / G downwards / B upwards / W0% 
R0% / G0% / B downwards / W upwards
171 180 R upwards / G0% / B0% / W downwards  R0% / G100% / B downwards / W0% 
R upwards / G100% / B0% / W0%
181 190
R100% / G downwards / B0% / W0% 
R100% / G0% / B upwards / W0% 
R downwards / G0% / B100% / W0% 
R0% / G upwards / B100% / W0%
191 200 RGBW
201 205 Customer White 1
206 210 Customer White 2
211 215 Customer White 3
216 220 Customer White 4
221 225 Customer White 5
226 230 Customer White 6
231 235 Customer White 7
236 240 Customer White 8
241 245 Customer White 9
246 250 Customer White 10
251 255 Customer White 11
8
0 No function
2 10 Automatic program 1
11 20 Automatic program 2
21 30 Automatic program 3
31 40 Automatic program 4
41 50 Automatic program 5
51 60 Automatic program 6
61 70 Automatic program 7
71 80 Automatic program 8
81 90 Automatic program 9
91 100 Customer program 1
101 110 Customer program 2
111 120 Customer program 3
121 130 Customer program 4
131 140 Customer program 5
141 150 Customer program 6
151 160 Customer program 7
161 170 Customer program 8

18 / 20
171 180 Customer program 9
181 190 Customer program 10
191 200 Customer program 11
201 255 Customer program 12
9 0 255 Speed channel 7 and 8 0 15 No function
16 255 Strobe slow – fast
10
0 10 No function
11 63 Single control
64 95 Control in groups of 2
96 127 Control in groups of 3
128 191 Control in groups of 4
192 255 Control in groups of 6
11 0 255 Dimmer red LED 1 0 – 100%
12 0 255 Dimmer green LED 1 0 – 100%
13 0 255 Dimmer blue LED 1 0 – 100%
14 0 255 Dimmer white LED 1 0 – 100%
… … … …
55 0 255 Dimmer red LED 12 0 – 100%
56 0 255 Dimmer green LED 12 0 – 100%
57 0 255 Dimmer blue LED 12 0 – 100%
58 0 255 Dimmer white LED 12 0 – 100%
59
0 – 9 All IDs 210 ID 21 233 ID 44
10 – 19 ID 1 211 ID 22 234 ID 45
20 – 29 ID 2 212 ID 23 235 ID 46
30 – 39 ID 3 213 ID 24 236 ID 47
40 – 49 ID 4 214 ID 25 237 ID 48
50 – 59 ID 5 215 ID 26 238 ID 49
60 – 69 ID 6 216 ID 27 239 ID 50
70 – 79 ID 7 217 ID 28 240 ID 51
80 – 89 ID 8 218 ID 29 241 ID 52
90 – 99 ID 9 219 ID 30 242 ID 53
100 – 109 ID 10 220 ID 31 243 ID 54
110 – 119 ID 11 221 ID 32 244 ID 55
120 – 129 ID 12 222 ID 33 245 ID 56
130 – 139 ID 13 223 ID 34 246 ID 57
140 – 149 ID 14 224 ID 35 247 ID 58
150 – 159 ID 15 225 ID 36 248 ID 59
160 – 169 ID 16 226 ID 37 249 ID 60
170 – 179 ID 17 227 ID 38 250 ID 61
180 – 189 ID 18 228 ID 39 251 ID 62
190 – 199 ID 19 229 ID 40 252 ID 63
200 – 209 ID 20 230 ID 41 253 ID 64
231 ID 42 254 ID 65
232 ID 43 255 ID 66

19 / 20
7. Photometrical data
8. Technical data
Power supply
Voltage 110 – 240 V / 50-60 Hz
Power consumption max. 180 W
Light source
LM type LED 4in1
Color spectrum RGBW
Power 180 W
Number / Power 12 x 15 W
Connections
Power in IP65
Power out IP65
XLR in/out IP65
Controlling
Sound-to-Light No
Automatic Yes
Master-Slave Yes
DMX512 Yes
Number of channels 3 / 4 / 5 / 8 / 11 / 59 channels
Hardware
Protection class IP65
Suitability Outdoor
Dimensions (L/BL/H) 1020 x 94 x 80 mm
Weight 10 kg

20 / 20
Importer:
B & K Braun GmbH
Industriestraße 2
D-76307 Karlsbad
www.bkbraun.com
[e-mail]