Vaxcel T0278 Instruction manual

Page 1 / 3
160729
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0278
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Hardware Package (included):
Decorative cover
Mounting Bracket Screw Fixture Mounting Screw
Mounting Strap Wire Connector X3
Mounting Screw X2
#8/32X1/2 in
Mounting Screw X2
#6/32 X1/2 in
Mounting Screw X2
#10/24 X1/4 in
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted Eave Mounted
Light fixture should be mounted as shown above when installed (depending upon type of installation)
Mounting Strap
Mounting Bracket
Outlet Box
Wire Connector
Back Plate
Mounting Screw
Light Head
Fixture Mounting Screw
Mounting Bracket Screw
FRONT
Decorative cover
IMPORTANT:
The fixture features a photocell sensor which enables the light to turn on at dusk and off at dawn automatically.

Page 2 / 3
160729
Turn off the power at fuse or circuit box.
Turn on the power at fuse or circuit box.
Installation Steps
Fig. 1
1. The mounting bracket is pre-assembled on the light fixture. Unscrew the decorative cover, fixture mounting screw in
order to remove the mounting bracket.
2. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using
two mounting screws that best fit the outlet box. Mounting bracket should sit flush against wall surface when secured.
(Choose one matching pair of suitable mounting screws from the 3 pairs provided)
3. Pull out the source wires from the outlet box. Make wire connections using wire
connectors as follows:
---Connect the black wire from the fixture to the “hot” wire from the power source.
(usually black)
---Connect the white wire from the fixture to the neutral wire from the power
source. (usually white)
---Connect the grounding wire from the fixture to the grounding wire from the
power source. (usually green / yellow insulation)
Carefully tuck the wires back into the outlet box.
4. Place mounting bracket against the outlet box, insert the mounting bracket screw
through the mounting bracket hole, thread mounting bracket screw into the center hole of the mounting strap. Tighten
the mounting bracket screw securely.
▲ When mounting to a wall, the “UP” arrow must point upward. (See Fig. 1)
▲ When mounting to an eave, the “UP” arrow must point toward the building.
5. Attach the back plate of the light fixture to the mounting bracket, secure it with the fixture mounting screw.
6. Push the decorative cover firmly into the fixture mounting screw hole on the light fixture.
7. With silicone caulking compound, caulk completely around where the mounting bracket meets the wall surface.
CAUTION: Be sure to caulk completely where the mounting bracket meets the wall surface to prevent water
from seeping into the outlet box.
8. Gently grasp the light heads and tilt them up or down, left or right to adjust the light coverage area. (See Fig. 2)
9. Keep the light head 30˚ below horizontal to avoid water damage
and electrical shock. Fig. 2
Note: When power is first applied, the light will turn on
immediately. Wait for 15 seconds to allow the sensor to warm up.
Assembly Kit
5076MM
(1 SET)
The following parts are available for re-order if damaged or missing.
Decorative cover
Mounting Bracket Screw Fixture Mounting Screw
Mounting Strap Wire Connector X3
Mounting Screw X2
#8/32X1/2 in
Mounting Screw X2
#6/32 X1/2 in
Mounting Screw X2
#10/24 X1/4 in
Spare Parts List:

Page 3 / 3
5-YEAR LIMITED WARRANTY:
All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase.
This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided
that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with proof
of purchase date; and (c) it is found upon inspection by us that the item(s) is / are defective as noted above. This warranty
does not cover labor costs, consequential damages, nor does it apply to any item(s) that have been improperly installed,
overloaded, altered, or otherwise abused by the customer, its agent(s) or employee(s). Finishes are specially excluded
from the terms of this warranty since they are subject to environmental maintenance deemed beyond our control. Other
than the described obligation, we assume no further liability with respect to the sale or use of our products.We make no
warranty, express or implied, and disclaim any warranty of merchantability or fitness for a particular purpose.
A: 5-1/8"
B: 5-3/8"
C: 6"
160729
A
B
C