VDO CANcockpit Series User manual

New Generation 2009
Flexible instrumentation with CAN bus technology
www.vdo.com
CANcockpit
Product Manual
VDO - eine Marke des Continental-Konzerns / VDO - A trademark of the Continental Corporation

Topic Chapter
Safety Instructions 1
Description of Functions 2
Installation Instructions 3
Testing Instructions ▼4
Software-Description 5
System Components, Spare Parts and Accessories 6
Data Sheets 7
General Information 8
Sales and Service Informations 9
▼= will follow
The reproduction, distribution and utilization of this document as well as the communication of its contents to others without
express authorization is prohibited. Offenders will be held liable for the payment of damages. All right reserved in the event of
the grant of a patent, utility model or design.
Overview of Chapter
Product Manual
Technische Änderungen vorbehalten Technical details subject to change
TU00-0726-0000002 0609

Technische Änderungen vorbehalten Technical details subject to change 1 - 1
TU00-0736-0000002 0609
1. Safety Instructions
Product Manual
Contents
Contents
1.1 Installation 2
Before installation 2
During installation 3
After installation 3
1.2 Electrical Connection 4
1.3 Sensors 5
1.3.1 Pressure Sensor for Oil 5
1.3.2 Temperature Sensor for Oil 6
1.3.3 Temperature Sensor for Engine Coolant 7
1.3.4 Fuel Level Sensor (Lever Type Sensor/Tubular Type Sensor) 8

1.1 Installation
• The product is only designed for use in land-bound vehicles (except motorcycles).
• Make sure that the engine cannot be unintentionally started during installation.
Before installation
• Withdraw ignition key from ignition lock.
• Note down all data in temporary electronic memories.
• Before installation refer to the vehicle documents for details of vehicle type and any special features.
• Refer to the construction diagrams to find out the positions of the fuel/hydraulic/pneumatic and electrical lines.
• Take account of any modifications to the vehicle which have to be considered during installation.
• Failure to use the product correctly may cause harm to people, property and the environment. Therefore make sure you
use our product correctly.
• Basic knowledge of vehicle electrics and mechanics is necessary for installation to prevent harm to people, property and
the environment.
• The product has been developed, manufactured and tested in accordance with the basic safety requirements of EC di-
rectives and the acknowledged state of the art.
• Short circuits
Short circuits in the vehicle's wiring can cause cable fires, battery explosions and damage to other electronic systems.
Therefore disconnect the minus pole of the vehicle battery before starting work.
If the vehicle has supplementary batteries, the minus poles of these batteries should also be disconnected.
• Modifying or tampering with the product may affect safety. Therefore it must not be modified or tampered with.
• When removing/installing seats, covers and the like, make sure that you do not damage lines or release plug connec-
tions.
• Possible data loss
When the batteries' minus poles are disconnected, all the temporary electronic memories lose their entered data.
Therefore, note down all the relevant data for re-programming before disconnection.
1. Safety Instructions
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 1 - 2
TU00-0736-0000002 0609
No smoking!
No naked flames or lights!

1.1 Installation
During installation
• During installation make sure that the product's components do not affect or restrict vehicle functions and are themsel-
ves not damaged.
• Only install undamaged parts in vehicles.
• During installation make sure that the product does not impair the field of vision and that the product is not positioned
within the impact range of the driver's or passenger's heads.
• When selecting the installation location, make sure there is sufficient space behind the drilled holes and the installation
opening.
• Take account of the routing of lines and cable leads.
• Do not select an installation location within the mechanical and electrical range of the airbag.
• Do not drill holes or cut openings in load-bearing or stabilizing struts or members.
• Err on the small side when predrilling installation apertures with cone-type cutters, compass or jig saws, or files, enlar-
ge if necessary and complete. Deburr edges. Always follow the tool manufacturer's safety instructions.
• When working beneath the vehicle, secure the vehicle in accordance with the vehicle manufacturer's instructions.
• If any work is necessary while the engine is running, take special care. Only wear suitable working clothes because of
the risk of injury due to pinching and burning. Long hair should be worn in a hair net.
• Only use the envisaged multimeters or diode-test lamps to measure wattages and currents in motor vehicles. The use
of conventional test lamps can cause damage to control units and other electronic systems.
After installation
• Firmly connect the earth cable to the minus pole of the vehicle battery.
• (Re-)program the data in the temporary electronic memories.
• Test all(!) vehicle functions.
• CANcockpit components to be cleaned with clear water only.
Observe the IP-degrees of protection (DIN 40050).
1. Safety Instructions
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 1 - 3
TU00-0736-0000002 0609

1.2 Electrical Connection
• Take account of the cable cross section
A reduction in the cable cross section results in a higher current density. This can cause the cable to heat up.
• When laying electric cables, use existing cable ducts and routes but without laying cables parallel to ignition cables or
cables leading to high current consumers. Fix the cables with cable tape or adhesive tape.
• Do not route cables over mobile components. Do not fasten cables to the steering column.
• Make sure that the cables are not exposed to tensile, compressive or shear forces.
• If the cables are routed through drilled holes, protect them with rubber sleeves or the like.
• Strip cables only with a cable stripper. Adjust the stripper so that no strands are damaged or severed.
Solder new cable connections only with the soft soldering process or use standard crimp connectors.
• Crimp connections should only be made with a crimping tool. Follow the tool manufacturer's safety instructions.
• Insulate exposed strands so that no short circuiting can occur.
• Faulty wiring can cause short circuiting. Wire the cables only in accordance with the electrical connection diagram.
1. Safety Instructions
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 1 - 4
TU00-0736-0000002 0609
Connect the cables in accordance with the electrical connection diagram.

Technische Änderungen vorbehalten Technical details subject to change 1 - 5
TU00-0736-0000002 0609
1.3 Sensors
1.3.1 Pressure Sensor for Oil
❒Sensor installation location: At the place provided by the engine manufacturer, equipment manufacturer or car manu-
facturer in the oil circulation system (most often in place of the oil pressure switch).
❒Sensor installation only when engine is cold.
❒When removing the oil pressure switch or the screw from the drilled hole for the oil pressure measuring system, collect
the oil running out of the system in a proper container and dispose of it in accordance with legal regulations.
max.
❒The values mentioned in the following table for the maximum tightening
torque (Nm max.) refer exclusively to the load-bearing capacity of products.
Prior to using the product, it is important to ask the manufacturer of the ve-
hicle, equipment system or engine in each instance for the maximum tor-
que (? Nm max.) value for the threaded hole into which the product is to be
screwed. Non-observance of the maximum tightening torque specified for
the threaded hole in each instance can result in damage to the vehicle, en-
gine or equipment system.
❒If the connection thread is cylindrical, a sealing washer or a sealing ring made of copper must be fitted.
❒Following sensor installation, fill up the system with the required quantity of specified oil.
1. Safety Instructions
Product Manual
M10 x 1 30 Nm
1/8 in. BSPF 30 Nm
1/8 - 27 NPTF 30 Nm
R 1/8 DIN 2999 30 Nm
M12 x 1,5 40 Nm
M12 x 1 50 Nm
M14 x 1,5 50 Nm
1/4 in. BSPF 60 Nm
1/4 - 18 NPTF 60 Nm
3/8 - 18 NPTF 60 Nm
M16 x 1,5 80 Nm
3/8 - 18 Dryseal NPTF 80 Nm
M18 x 1,5 100 Nm

1.3 Sensors
1.3.2 Temperature Sensor for Oil
❒Sensor installation location: At the place provided by the engine manufacturer, equipment manufacturer or car manu-
facturer in the oil circulation system (e. g. oil drain plug).
❒Sensor installation only when engine is cold.
❒When removing the oil drain plug, collect the oil running out of the system in a proper container and dispose of it in ac-
cordance with legal regulations. max.
❒The values mentioned in the following table for the maximum tightening tor-
que (Nm max.) refer exclusively to the load-bearing capacity of products.
Prior to using the product, it is important to ask the manufacturer of the ve-
hicle, equipment system or engine in each instance for the maximum tor-
que (? Nm max.) value for the threaded hole into which the product is to be
screwed. Non-observance of the maximum tightening torque specified for
the threaded hole in each instance can result in damage to the vehicle, en-
gine or equipment system.
❒If the connection thread is cylindrical, a sealing washer or a sealing ring made of copper must be fitted.
❒Following sensor installation, fill up the system with the required quantity of specified oil.
1. Safety Instructions
M10 x 1 10 Nm
M10 x 1.5 10 Nm
1/8 - 27 NPTF 10 Nm
M12 x 1.5 15 Nm
1/2 - 20 Gang 15 Nm
M14 x 1.25 20 Nm
M14 x 1.5 20 Nm
5/8 - 18 UNF - 3A 20 Nm
1/2 In. 20 Whit. S 20 Nm
1/4 - 18 NPTF 20 Nm
M16 x 1.5 30 Nm
M18 x 1.5 30 Nm
M20 x 1.5 30 Nm
M22 x 1.5 30 Nm
M24 x 1.5 30 Nm
M26 x 1.5 30 Nm
1/2 - 14 NPTF 30 Nm
3/8 - 18 NPTF 30 Nm
R 1/2 30 Nm
R 3/8 30 Nm
3/8 - 18 Dryseal NPTF 30 Nm
3/4 - 16 UNF-3A 30 Nm
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 1 - 6
TU00-0736-0000002 0609

1.3 Sensors
1.3.3 Temperature Sensor for Engine Coolant
❒Sensor installation location: At the place provided by the engine manufacturer, equipment manufacturer or car manu-
facturer in the coolant circulation system (e.g. in place of the temperature warning switch) or in the coolant hose.
❒Sensor installation only when engine is cold.
❒Collect the coolant running out of the system in a proper container and dispose of it in accordance with legal regulations.
max.
❒The values mentioned in the following table for the maximum tightening tor-
que (Nm max.) refer exclusively to the load-bearing capacity of products.
Prior to using the product, it is important to ask the manufacturer of the ve-
hicle, equipment system or engine in each instance for the maximum tor-
que (? Nm max.) value for the threaded hole into which the product is to be
screwed. Non-observance of the maximum tightening torque specified for
the threaded hole in each instance can result in damage to the vehicle, en-
gine or equipment system.
❒If the connection thread is cylindrical, a sealing washer or a sealing ring made of copper must be fitted.
❒Following sensor installation, fill up the system with the required quantity of the compositon specified coolant.
1. Safety Instructions
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 1 - 7
TU00-0736-0000002 0609
M10 x 1 10 Nm
M10 x 1.5 10 Nm
1/8 - 27 NPTF 10 Nm
M12 x 1.5 15 Nm
1/2 - 20 Gang 15 Nm
M14 x 1.25 20 Nm
M14 x 1.5 20 Nm
5/8 - 18 UNF - 3A 20 Nm
1/2 In. 20 Whit. S 20 Nm
1/4 - 18 NPTF 20 Nm
M16 x 1.5 30 Nm
M18 x 1.5 30 Nm
M20 x 1.5 30 Nm
M22 x 1.5 30 Nm
M24 x 1.5 30 Nm
M26 x 1.5 30 Nm
1/2 - 14 NPTF 30 Nm
3/8 - 18 NPTF 30 Nm
R 1/2 30 Nm
R 3/8 30 Nm
3/8 - 18 Dryseal NPTF 30 Nm
3/4 - 16 UNF-3A 30 Nm

1.3 Sensors
1.3.4 Fuel Level Sensor (Lever Type Sensor/Tubular Type Sensor)
❒An installation opening remaining to be made in the tank at a suitable point for supply level measurement or at an in-
stallation flange or installation opening already provided by the tank manufacturer.
❒If an installation opening must be made, the tank must be completely drained first. Fill the fuel into an approved contai-
ner.
❒Risk of explosion exists due to presence of residual gases in the tank! Make sure that the tank is aired
sufficiently (approx. 10 minutes).
❒Make a preliminary hole in the installation opening using a drill and then finish the hole using a compass saw or piercing
saw. Comply with the safety instructions of the tool manufacturer. Clean the tank of residue from the drilling or sawing
work.
❒The safety instructions given by the welding equipment manufacturer and the working regulations applying to welding
work must be respected when welding the tank flange.
1. Safety Instructions
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 1 - 8
TU00-0736-0000002 0609

Technische Änderungen vorbehalten Technical details subject to change 2 - 1
TU00-0736-0000002 0609
Contents
Contents
1. System 3
1.1 Main Features 3
1.1.1 Block Diagram CANcockpit 3
1.2 Mechanical Concept 3
1.3 Safety Concept 4
1.3.1 Sensors 4
1.3.2 System Check 4
1.3.3 Satbus 4
1.3.4 WINgauge 4
2. Master Gauges 5
2.1 General Features 5
2.1.1 Main Functions 5
2.2 Mechanical Concept 6
2.2.1 Master dia. 80 mm 6
2.2.2 Master dia. 85 mm 6
2.2.3 Master dia. 100 mm 6
2.3 Input Signal Processing 7
2.3.1 Analog Inputs 7
2.3.1.1 Grounding Concept 7
2.3.1.2 Sensors 7
2.3.2 Input Signal Processing applied to the two frequency inputs 7
2.3.3 Input Signal Processing for CANbus messages 8
2.4 PIN Assignment Description 9
2.4.1 Technical Description 9
2.5 Display Functions 12
2.5.1 Navigation through Display 12
2.5.2 Display Layout 12
2.5.3 Display Functions 14
2.5.3.1 Main Display (Odometer, Hourmeter) 14
2.5.3.2 Alarm Display 14
2.5.3.3 CAN DTC Display 15
2.5.3.4 Warning Display 15
2.5.3.5 Service Message 16
2.5.3.6 Physical Value Display 16
2.5.4 Alarm- and Warning Functions 17
2.5.4.1 Description of the Outputs 17
2.5.4.2 Switch Output Acknowledgement Function 17
2.5.4.3 Alarm and Warning Trigger Conditions 18
2.5.4.4 Alarm and Warning Trigger enabling with Engine running 18
2.5.4.5 Alarm and Warning State Diagram (Maximum Value Algorithm) 19
2. Functional Specification
Product Manual

2.5.5 Service 21
2.5.5.1 Reset of Service messages 21
2.5.6 CAN (SAE J1939) DTC (Diagnostic Trouble Codes) messages 22
2.5.6.1 CAN SAE J1939 Elements 22
2.5.6.2 CAN DTC Information Display Requirements 23
2.5.6.3 CAN DTC Display Functions 23
2.5.6.4 Speedometer Master Gauge 25
2.5.6.5 Tachometer Master Gauge 27
3. Satellite Gauges 28
3.1 Mechanical concept 28
3.2 Fault modes 28
3.3 Satellite gauge address 29
3.4 Warning Lamp inside the Satellite Gauge 29
3.5 Tolerance 29
A. Technical Data 30
B. Applied Standards 31
2. Functional Specification
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 2 - 2
TU00-0736-0000002 0609

1. System
1.1 Main Features
• Master-Slave relationship between Master gauge and other instruments
• Up to 16 Slave functions on one Master instrument or 32 with the use of two Master instruments
• CAN protocol flexibility ( processing two protocols simultaneously)
• Modular "plug & play" as needed
• Analogue sensor compatible
• Frequency inputs
• Dot-matrix information display
• Switch outputs available
• Flexible to customer needs
1.1.1 Block Diagram CANcockpit
1.2 Mechanical Concept
The Masters are 80, 85 and 100 mm in diameter, the Satellite gauges dia. 52, 80 and 100 mm.
The dials are translucent backlighted. The illumination of the gauges is realised with white LED's.
The backlighting of the LCD has a yellow LED. The warning lamp in the slave can have a red or yellow LED.
The housing and bezel are made of non-flammable plastic, the design is like a triangle with the black color RAL 9005. The be-
zel is clipable. The lens is flat and frosted. The pointer has a PC hub in black and the pointer arm is OL 5105 (white -coated on
the underside). The pointer type is translucent illuminated.
The housings have an indent in the thread at 6 o'clock position, so that an optional key can be
used according to SAE J1226 and SAE J 1399.
The movements are front-mounted stepper motors MW2000, only clockwise indication.
2. Functional Specification
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 2 - 3
TU00-0736-0000002 0609

1.3 Safety Concept
1.3.1 Sensors
Analog sensors can be checked for short and open circuit.
1.3.2 System Check
When the trip-reset button is pressed while ignition is being turned on, the system-check function is activated and clears the
contents of the DTC List.
If there are any active service messages, they will be displayed on the Dot-Matrix Display starting with the first active service
message. If the reset button is then pressed and held for 5 seconds or longer, this service message will be reset. The next
active service message is displayed thereafter.
To proceed to the next active service message without resetting the displayed code, the button needs to be pressed shortly
(<5 sec). If all active service codes have been displayed, the system check function is started as described below:
1. All warning lamps and illumination of all gauges are activated for 3 seconds.
2. The Master gauge initializes all configured satellite gauges and waits until they are ready or a Satbus timeout occurs.
3. During time.this, all LCD-Dots are turned on for about 1.5 sec, all pointers are moved to their end value
4. Then all LCD-Dots are turned off and the pointers move back to zero, for about 1.5 sec too, and all warning lamps and
illumination will be turned off
5. Firmware version and Check sum of the EEPROM in hexadecimal format are displayed for about 10 sec.
The display format is as follows:
XX represents a hex-coded value
1.3.3 Satbus
After ignition for synchronisation the Master gets feedback from the satellites.
A timeout function can be programmed too. If more satellites are configured, the Master will not get feedback from all gauges.
After a timeout of about 14 seconds, the Master will act as described before, when the Master gets feedback from all satelli-
tes.
During normal operation there is no feedback from the satellites.
1.3.4 WINgauge
A system diagnosis function for testing all in- and outputs is implemented in the WINgauge Software.
2. Functional Specification
Product Manual
Small
display
line Format Description
2hXX sXX.XX dd_mm_yyyy hXX specifies the Hardware version relevant to the Firmware
sXX.XX refers to the Firmware version, for example s12.A8 stands for V06
dd_mm-yyyy is the Firmware date in day, month and full-year format.
4nXXXXwXXyXX cXXXXXX nXXXX is the WINgauge serial number of the device as programmed into the
EEPROM.
wXXyXX displays the production week and year in short format.
cXXXXXX shows the actual 3-byte Checksum of the EEPROM as calculated during
the system check.
Technische Änderungen vorbehalten Technical details subject to change 2 - 4
TU00-0736-0000002 0609

Technische Änderungen vorbehalten Technical details subject to change 2 - 5
TU00-0726-0000002 0609
2. Master Gauges
2.1 General Features
The design concept for this design includes:
• 2x High-speed Full-CANbus interface V2.0B compatible.
• Half-duplex serial link to satellite gauges.
• VMC SCAL CDVV Microcontroller with identical firmware.
• Stepper motor MW2000 directly controlled by Microcontroller.
• Satellite gauges use SM2 stepper motor driven by ISM IC.
• LED illumination concept.
• 132 x 33 dots matrix LCD.
• Wide input voltage range switch mode power supply.
• Diagnostic Interface for configuration.
2.1.1 Main Functions
2. Functional Specification
Product Manual
Inputs
Outputs
CAN_1
CAN_2
Frequency_1
Frequency_2
Sensor Input_1
Sensor Input_2
Sensor Input_3
4 to 20 mA
Voltage Input
Illumination
term.15
term.30
Inp
ut
Sig
nal
Pr
oc
es
sin
g
Analogue Gauge Functions
Warning Functions
Odometer,
Tripmeter
Hourmeter
,
Triphourmeter
Service Intervals
Illumination Control
Power Supply Control
Parameter Memory (EEPROM)
Diagnostics
Frequency-Divider
Ou
tpu
t
Sig
nal
Pr
oc
es
sin
g
Flash-Boot-Loader
Internal MW2000
SatBus
-Gauges
LCD
Sat-Gauge Warning Lamps
Switch Output_1
Switch Output_2
LCD
LCD
Master Gauge Illumination
SatBus
-Gauge Illumination
Master Gauge Supply
SatBus
Supply
Sensor Supply
K-Line Diagnostics
Diagnostic Trouble Codes

2.2 Mechanical Concept
As the same LCD is used for different Master gauge diameters the pointer position has different eccentricities and indication
angles.
The connectors are 26-Pin MODU II-Connector and 4-Pin MATE-N-LOK from AMP.
2.2.1 Master dia. 80 mm
Two PCB's are necessary for this diameter. They are connected with a standard pin connector
and two distance towers.
2.2.2 Master dia. 85 mm
The PCB assemblies and their corresponding parts of the Ø 80 mm and Ø 85 mm gauges are identical. The difference bet-
ween the two gauges is the position of the stepper motor on the PCB so that the eccentricity of 7 mm in the Ø 80 mm gauge
can be reduced to 4.5 mm in the Ø 85 mm gauge.
2.2.3 Master dia. 100 mm
For this size, only one PCB assembly is necessary. Input Signal Processing.
Gauge diameter [mm] Eccentricity [mm] Indication angle
80 7210°
85 4.5 216°
100 0206°
2. Functional Specification
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 2 - 6
TU00-0726-0000002 0609

2.3 Input Signal Processing
2.3.1 Analog Inputs
All sensor characteristics can be defined with the WINgauge Software.
2.3.1.1Grounding Concept
The Master gauge has two main ground lines. Ground term.31 is connected to the vehicle's body (negative battery terminal)
and Sensor Ground is supplied from the instrument; insulated return sender are necessary. The Sensor Ground should not be
connected to vehicle ground, which would result in a higher current flowing through this line and thus produce a signal noise
and measurement error. Sensor Ground and Ground term.31 are joined together inside the Master Gauge. This grounding
principle is necessary to accurately measure analog values. Ground shift on Sensor Ground is minimized by this concept.
2.3.1.2Sensors
The static and dynamic voltage drop of the sensors should not exceed 0.5 V.
Pressure: 10 - 184 Ohms
Temperature: 10 - 700 Ohms
Fuel lever type: 3 - 180 Ohms
Fuel dip-pipe: 0.5 - 90 Ohms
Other sensors: 4 - 20 mA
Other sensors: 0 - 5 V
2.3.2 Input Signal Processing applied to the two frequency inputs
Frequency 1:
The standard modules can be changed to 500 < k < 400 000 pulses/km or miles for the Speedometer
and 0.5 - 400 pulses/rev for the Tachometer.
Maximum frequency is 40 kHz (2 kHz via internal divider).
Frequency 2 as Hall Sensor / Terminal W:
500 < k < 65000 pulses/km or miles for Speedometer and 0.5 - 65 pulses/rev for Tachometer.
Maximum frequency is 2 kHz.
2. Functional Specification
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 2 - 7
TU00-0726-0000002 0609
,
Fuel
Sender
Oil Pressure
Sensor
Engine-
Temperature
Vehicle
Sensor-Ground
Chassis GND
Gauge2000 System
Ground Term.31
CANcockpit System

2.3.3 Input Signal Processing for CANbus messages
Example of SAE J1939 Messages received on one of the two CANbus Interfaces.
The Master Gauge CANbus interface conforms to CAN 2.0B specification and supports extended (29Bit) identifiers. The
Gauge acts as a "Standard ECU, which is non-configurable as defined in SAE J1939. The application layer is based on SAE
J1939/71 Rev 2008-01.
Additional communication protocol is CAN Open
For this the different CANbus data bases will be provided by the WINgauge configuration.
2. Functional Specification
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 2 - 8
TU00-0726-0000002 0609

Technische Änderungen vorbehalten Technical details subject to change 2 - 9
TU00-0726-0000002 0609
2.4 PIN Assignment Description
Master:
2.4.1 Technical Description
PIN 1: Power Supply (terminal 30)
VBatt = + 10,5 V to + 32 V
The instrument is supplied with permanent power through this terminal. Current consumption varies depending on the instru-
ments operating mode (standby or active) and number of Slaves.
PIN 2: Ground (terminal 31)
Power ground of the instrument.
PIN 3, 4: CANbus Interface 1
High-Speed Full CANbus V2.0B compatible (10, 20, 50, 125, 250, 500 kbit/s, 1 Mbit/sec.).
12 V and 24 V system compatible.
Cable: shielded, twisted pair with a drain.
Cable Impedance: nom. 120 Ω.
Topology: linear Bus
Trunk Length: max. 40 meters
Drop Length: max. 1 meter
Termination: 2 resistors 120 Ω at each end of the bus.
Related documents: ISO 11898, SAE J1939/11
UA combination of 29 bit ID and 11 bit ID can`t be processed!
PIN 5, 6: CANbus Interface 2
See on CANbus Interface 1.
PIN 7: Not connected
PIN 8: K-Line Diagnostic Interface
Programming of the EEPROM and the diagnostics carried out via serial diagnostic interface K-Line.
PIN 9, 25: Analog Input 1
Range: 0.5 - 200 Ω
Standard sensors: Tube-type Sensor: 0,5 Ω to 90 Ω
Lever-type Sensor: 3 Ω to 180 Ω.
Sensor has to be connected between theese pins.
PIN 10, 25: Analog Input 2
2. Functional Specification
Product Manual
Pin Description Pin Description
1Power Supply (terminal 30) 14 + 8 V DC for sensor supply
2Ground (terminal 31) 15 0 - 5 V DC Input
3CAN1 _High 16 Illumination (terminal 58 (d))
4CAN1 _Low 17 Ignition (terminal 15)
5CAN2 _High 18 Frequency Input 2 (0-2 kHz)
6CAN2 _Low 19 Frequency Input 1 (0-40 kHz)
7NC 20 Switch-Output_1
8k-Line 21 Switch-Output_2
9Analog Input 1 (0,5 - 200 Ω)22 NC
10 Analog Input 2 (0,5 - 300 Ω)23 NC
11 Analog Input 3 (10 - 700 Ω)24 External Switch
12 4 - 20 mA Input 25 Analog GND
13 4 - 20 mA GND 26 Frequency GND

Range: 0.5 - 300 Ω
Standard sensors: Pressure sensor(10 - 184 Ω)
Sensor has to be connected between theese pins.
PIN 11, 25: Analog Input 3
Range: 10 - 700 Ω
Standard sensors: Temperature sensor (38 - 700 Ω)
Sensor has to be connected between theese pins.
PIN 12, 13: 4 to 20 mA Input
Range: 4 to 20 mA
A resistor converts the 4 - 20 mA current into proportional voltage. Results are sampled every 31.25 msec by the
Microprocessor.
PIN 14: +8 V sensor power supply:
Voltage: +8 V - 0 %, +10 %
Max. current: 50 mA
UThis output can be used only at 24 V power supply.
PIN 15: 0 - 5 V Input :
Range: 0 - 5 V
Results are sampled every 31.25 msec by the Microprocessor.
PIN 16: Illumination Input (terminal 58 (d):
Range: 0 to UBat. (battery voltage)
Dimming of Master gauge illumination and attached Satellite gauges is controlled by the voltage amplitude at the Illumination
input.
PIN 17: Ignition (terminal 15)
Vign.= + 10,5 V to + 32 V
The Microprocessor senses the voltage at the input and turns it into active mode, if the ignition is turned on.
PIN 18, 26: Frequency Input 2
Hall Sensor and terminal W:
Max. Frequency: 2 kHz
U high min.: 5 - 7 V according to the configurated pulses
Signal type: square, sinus
Max. offset: 0.5 V
Off current max.: 100 µA
Duty cycle: 50 ± 15 %
Pulse ratio: 500 - 65 000 pulses/km or miles
Pulse/rev: 0.5 - 65 pulses/revolution
The Instrument has a pull-up resistor at the ignition in the input circuit. Input can be either road speed or engine speed.
Selection by configuration.
UOnly one frequency input (either Input 1 or 2) can be defined as road speed input.
PIN 19, 26: Frequency Input 1
Universal Frequency Input
Max. Frequency: 40 kHz (2 kHz via internal divider, 1:1; 1:2; ... 1:20)
Uhigh min: 1.5 - 10 V according to the configurated pulses
Signal type: square, sinus
Max. offset: 0.5 V
Off current max.: 100 µA
Duty cycle: 50 ± 15%
Pulse ratio: 0.5 - 400 pulses/revolution
The instrument has a pull-up resistor at ignition in the input circuit. Input can be either road speed or engine speed. Selection
2. Functional Specification
Product Manual
Technische Änderungen vorbehalten Technical details subject to change 2 - 10
TU00-0726-0000002 0609