Veeder-Root TLS-350R PLUS User manual

Manual No: 577013-972 ●Revision: E
Installation Manual
MAG-XL Flex Probe

Notice
Veeder-Root makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Veeder-Root shall not be liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this publication.
Veeder-Root reserves the right to change system options or features, or the information contained in this publication.
This publication contains proprietary information which is protected by copyright. All rights reserved. No part of this publication
may be photocopied, reproduced, or translated to another language without the prior written consent of Veeder-Root.
Contact TLS Systems Technical Support for additional troubleshooting information at 800-323-1799.
DAMAGE CLAIMS / LOST EQUIPMENT
Thoroughly examine all components and units as soon as they are received. If any cartons are damaged or missing, write a
complete and detailed description of the damage or shortage on the face of the freight bill. The carrier's agent must verify the
inspection and sign the description. Refuse only the damaged product, not the entire shipment.
Veeder-Root must be notified of any damages and/or shortages within 30 days of receipt of the shipment, as stated in our Terms
and Conditions.
VEEDER-ROOT’S PREFERRED CARRIER
1. Contact Veeder-Root Customer Service at 800-873-3313 with the specific part numbers and quantities that were missing
or received damaged.
2. Fax signed Bill of Lading (BOL) to Veeder-Root Customer Service at 800-234-5350.
3. Veeder-Root will file the claim with the carrier and replace the damaged/missing product at no charge to the customer.
Customer Service will work with production facility to have the replacement product shipped as soon as possible.
CUSTOMER’S PREFERRED CARRIER
1. It is the customer’s responsibility to file a claim with their carrier.
2. Customer may submit a replacement purchase order. Customer is responsible for all charges and freight associated with
replacement order. Customer Service will work with production facility to have the replacement product shipped as soon as
possible.
3. If “lost” equipment is delivered at a later date and is not needed, Veeder-Root will allow a Return to Stock without a restocking
fee.
4. Veeder-Root will NOT be responsible for any compensation when a customer chooses their own carrier.
RETURN SHIPPING
For the parts return procedure, please follow the appropriate instructions in the "General Returned Goods Policy” pages in the
"Policies and Literature" section of the Veeder-Root North American Environmental Products price list. Veeder-Root will not
accept any return product without a Return Goods Authorization (RGA) number clearly printed on the outside of the package.
FCC INFORMATION
This equipment complies with the requirements in Part 15 of the FCC rules for a Class A computing device. Operation of this
equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take
whatever steps are necessary to correct the interference.
©Veeder-Root 2012. All rights reserved.

Warranty
TLS-350R, TLS-350 PLUS, TLS-350J AND TLS-300I/C MONITORING SYSTEMS
We warrant that this product shall be free from defects in material and workmanship for a period of one (1) year from the date of
installation or twenty-four (24 months) from the date of invoice, whichever occurs first. During the warranty period, we or our
representative will repair or replace the product, if determined by us to be defective, at the location where the product is in use
and at no charge to the purchaser. LAMPS, FUSES, AND LITHIUM BATTERIES ARE NOT COVERED UNDER THIS
WARRANTY.
We shall not be responsible for any expenses incurred by the user.
This warranty applies only when the product is installed in accordance with Veeder-Root’s specifications, and a Warranty
Registration and Checkout Form has been filed with Veeder-Root by an authorized Veeder-Root Distributor. This warranty will not
apply to any product which has been subjected to misuse, negligence, accidents, systems that are misapplied or are not installed
per Veeder-Root specifications, modified or repaired by unauthorized persons, or damage related to acts of God.
If “Warranty” is purchased as part of the Fuel Management Service, Veeder-Root will maintain the equipment for the life of the
contract in accordance with the written warranty provided with the equipment. A Veeder-Root Fuel Management Services
Contractor shall have free site access during Customer’s regular working hours to work on the equipment. Veeder-Root has no
obligation to monitor federal, state or local laws, or modify the equipment based on developments or changes in such laws.
MODULES, KITS, OTHER COMPONENTS (PARTS PURCHASED SEPARATE OF A COMPLETE CONSOLE)
We warrant that this product, exclusive of lithium batteries, shall be free from defects in material and workmanship for
a period of fifteen (15) months from date of invoice. We warrant that the lithium batteries shall be free from defects
in material and workmanship for a period of 90 days from date of invoice. We will repair or replace the product if the
product is returned to us; transportation prepaid, within the warranty period, and is determined by us to be defective.
This warranty will not apply to any product which has been subjected to misuse, negligence, accidents, systems that
are misapplied or are not installed per Veeder-Root specifications, modified or repaired by unauthorized persons, or
damage related to acts of God.
We shall not be responsible for any expenses incurred by the user.
MAG-XL FLEX PROBE
The same warranty policies for the MAG Plus Rigid Probe apply to MAG-XL Flex Probe. When the Probe is
purchased with a monitoring system (console), the warranty period is one (1) year from the date of installation or
twenty-four (24) months from the invoice date, whichever occurs first. Parts and labor are covered in this warranty.
When the Probe is purchased individually, it has a 15-month parts only warranty from the invoice date. Please refer
to the Policies and Literature section in the Price Book.
Veeder-Root will not warranty the probe if its damage is caused by failing to follow the Veeder-Root MAG-XL
Installation & Setup Manual (577013-972). Each MAG-XL Flex Probe is made to order, and therefore cannot be
returned for credit.

Table of Contents
iviv
Introduction
System Requirements ......................................................................................................1
Contractor Certification Requirements ..............................................................................1
Related Documents ..........................................................................................................2
Product Marking Information .............................................................................................2
Related Documents ..................................................................................................2
Safety Warnings ...............................................................................................................4
Safety Symbols .................................................................................................................4
GENERAL PRECAUTIONS ..............................................................................................5
SPECIAL TOOLS REQUIRED .................................................................................5
General AST Guidelines ...................................................................................................5
AST Construction Safe Work Practices ............................................................................6
Personal Protective Equipment ........................................................................................6
Before you Begin ..............................................................................................................6
MAG-XL Flex Probe Operating Parameters .....................................................................7
National Electrical Code Compliance ................................................................................8
MAG-XL Flex Probe Wire Length .............................................................................8
Veeder-Root Parts ............................................................................................................8
Customer Supplied Parts ..................................................................................................8
Example Drawings
Example MAG-XL Flex Probe Site Layout Drawing ..........................................................9
MAG-XL Flex Probe Dimensions ....................................................................................10
Example MAG-XL Flex Probe Installation in Tank Manway ...........................................12
Example MAG-XL Flex Probe Installation in Existing Tank Opening ..............................13
Component Dimensions .................................................................................................14
MAG-XL Flex Probe Installation
Pre-Installation Component Setup and Functional Check ..............................................15
Assemble the Battery Pack Mounting Bracket ................................................................15
Probe Installation - Manway 4-Inch Riser Pipe.......................................................15
Probe Installation - Top of Tank 2-Inch Pipe Opening............................................15
Unpack the MAG-XL Flex Probe ....................................................................................16
Assemble the MAG-XL Flex Probe Components ............................................................17
Probe Installation - Manway 4-Inch Riser Pipe.......................................................17
Probe Installation - Top of Tank 2-Inch Pipe Fitting ...............................................18
Install the MAG-XL Flex Probe Assembly .......................................................................19
Probe Installation - Manway 4-Inch Riser Pipe.......................................................19
Probe Installation - Top of Tank 2-Inch Pipe Fitting ...............................................20
Installing the TLS XL-Transmitter ...................................................................................20
TLS XL-Transmitter Installation - Manway 4-Inch Riser Pipe (ref. Figure 13) ........20
TLS XL-Transmitter Installation - Top of Tank 2-Inch Pipe fitting (ref. Figure 14) ..21
Connecting MAG-XL Flex Probe Wiring .........................................................................23
TLS Console Setup for MAG-XL Flex Probe
Height Reading Adjustment ............................................................................................26
TLS Limit Calculations ....................................................................................................28
Limit Calculation Example ......................................................................................28
Vertical Tank Volume Calibration ....................................................................................30

Table of Contents
v
MAG-XL Flex Probe Troubleshooting
Troubleshooting ..............................................................................................................31
Probe Out or No Probe Detected ...........................................................................31
Incorrect Product Height Reading ..........................................................................31
Figures
Figure 1. Site drawing - example TLS RF wireless 2 system site layout –
two Mag-XL Probes ................................................................................9
Figure 2. MAG-XL Flex Probe parameters ..........................................................10
Figure 3. MAG-XL Flex Probe installation with riser pipe, top mounted
in tank man way ....................................................................................12
Figure 4. MAG-XL Flex Probe installation without riser pipe, top mounted
in existing tank opening ........................................................................13
Figure 5. Wireless component dimensions ..........................................................14
Figure 6. Attaching conduit hangers to battery mounting bracket ........................16
Figure 7. Do not bend top 2 feet of probe ............................................................17
Figure 8. Do not twist one coil 90° from the others ..............................................17
Figure 9. MAG-XL Flex Probe components - man way install .............................18
Figure 10. MAG-XL Flex Probe components - pipe fitting install ...........................18
Figure 11. Correctly lowering probe into tank ........................................................19
Figure 12. Incorrectly lowering probe into tank ......................................................19
Figure 13. Installing TLS XL-Transmitter - man way riser pipe .............................22
Figure 14. Installing TLS XL-Transmitter - tank 2-inch pipe fitting .........................23
Figure 15. Connecting input wiring to transmitter terminal blocks .........................24
Figure 16. Connecting probe and battery pack cables to the
TLS XL-Transmitter ..............................................................................24
Figure 17. In-tank setup for TLS Consoles used with MAG-XL Flex Probes .........27
Figure 18. Alarm Limit Settings ..............................................................................29
Figure 19. Volume calibration examples ................................................................30
Tables
Table 1. MAG-XL Flex Probe Specifications .........................................................11

1
Introduction
The MAG-XL RF wireless probe is designed for inventory-only monitoring of extra large in-ground and above-
ground tanks in applications where in-ground probe wiring is either impractical or non-existent. Procedures
contained within this manual include:
• Installing the MAG-XL Flex Probe in the top of the tank.
• Mounting the TLS XL-Transmitter and battery pack to the tank riser
• Connecting the MAG-XL Flex Probe cable and battery pack cable to the transmitter.
Other required devices, such as the TLS RF Wireless 2 (W2) System and the TLS console are to be installed
following instructions shipped with those devices.
IMPORTANT!
It is imperative that you read and follow the handling warnings and installation instructions discussed
in this manual to avoid damaging the MAG-XL Flex Probe and voiding the warranty.
System Requirements
The Veeder-Root Wireless 2 (W2) System replacement/spare parts are listed below:
• 330020-668 TLS RF Console for Wireless 2 & MAG-XL Flex Probes
• 330020-673 MAG-XL Transmitter for MAG-XL Flex Probes
• 330020-674 Transmitter for Wireless 2 devices
• 330020-669 Receiver for Wireless 2 & MAG-XL Flex Probes
• 330020-670 Repeater for Wireless 2 & MAG-XL Flex Probes
Contractor Certification Requirements
Veeder-Root requires the following minimum training certifications for contractors who will install and setup the
equipment discussed in this manual:
Installer (Level 1) Certification: Contractors holding valid Installer Certification are approved to perform wiring
and conduit routing; equipment mounting; probe, sensor and carbon canister vapor polisher installation; wireless
equipment installation; tank and line preparation; and line leak detector installation.
ATG Technician (Level 2/3 or 4) Certification: Contractors holding valid ATG Technician Certifications are
approved to perform installation checkout, startup, programming and operations training, system tests,
troubleshooting and servicing for all Veeder-Root Series Tank Monitoring Systems, including Line Leak Detection.
In addition, Contractors with the following sub-certification designations are approved to perform installation
checkout, startup, programming, system tests, troubleshooting, service techniques and operations training on the
designated system.
• Wireless 2
• Tall Tank
Warranty Registrations may only be submitted by selected Distributors.

Introduction Related Documents
2
Related Documents
577013-964 TLS RF Wireless 2 System (W2) Installation and Maintenance Guide
Product Marking Information
RELATED DOCUMENTS
Documents Required to Install Equipment
This intrinsically safe apparatus is only for use as part of a Veeder-Root Automatic Tank Gauging System (ATG
Console with probes and sensors). To install intrinsically safe apparatus, use the specific control drawing that
appears on the nameplate of the applicable associated apparatus (ATG Console):
The control drawings contain information related to the correct installation of the overall intrinsically Safe System.
This includes information such as maximum number of apparatus, specific apparatus allowed in the system,
maximum cable lengths, references to codes, proper grounding and so on. Control drawings can be found on the
accompanying Compact Disk (TECH DOCS CD) or on the internet at veeder.com under SUPPORT; VR
TECHNICAL DOCUMENTS; DRAWINGS.
Equipment
UL/cUL Control Drawing
Document No.
Associated Apparatus
TLS-450/8600 331940-008
TLS-350, TLS-350R 331940-011
TLS-300 331940-013
TLS-50 or TLS2 or TLS-IB 331940-014
TLS4/8601 331940-018
TLS-XB/8603 331940-019
Intrinsically Safe Apparatus for Wireless Applications
Tank Gauge Accessories 331940-012

Introduction Product Marking Information
3
Product Label Contents
CLASS I, Division 1, Group D
CLASS 1, Zone 0, Group IIA
Hazardous Location
Intrinsically Safe (I.S.) Apparatus
XL TRANSMITTER
VT : 6.1 V
IT: 208 mA
Po: 0.32 W
Co: 500 µF
Lo: 3.0 mH
COMMON (-)
GENERAL PRODUCT WIRING DIAGRAM
POWER (+)
INPUT
POWER
DATA +
Probe Output Ratings
INTRINSICALLY SAFE APPARATUS INTRINSICALLY SAFE APPARATUS
INTRINSICALLY SAFE APPARATUS
PROBE
332425
TLS RF
BATTERY
PACK
PWR
DATA
COM
MAG-XL RF SYSTEM
I.S. CIRCUIT FOR HAZLOC DEVICE
F/N XXXXXX-XXX
S/N XXXXXX
-40°C < Ta< +60°C
CL I, DIV. 1, GP.D
CL I, ZONE 0
AEx iaIIA
Ex iaIIA
TC=T4 MANUAL NO. 577013-972
SECURITE INTRINSEQUE

Introduction Safety Warnings
4
Safety Warnings
To protect yourself and your equipment, observe the following warnings and important information:
Failure to install this product in accordance with its instructions and warnings will result in voiding of all
warranties with this product.
Safety Symbols
The following safety symbols may be used throughout this manual to alert you to important safety hazards and
precautions.
WARNING
This product is to be installed in systems operating near locations where highly combustible
fuels or vapors may be present.
FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY PRECAUTIONS
COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, RESULTING IN SERIOUS INJURY OR
DEATH.
1. Read and follow all instructions in this manual, including all safety warnings to protect
yourself and others from serious injury, explosion, or electrical shock.
2. Comply with all applicable codes including: the National Electrical Code; federal, state, and
local codes; and other applicable safety codes.
3. To protect yourself and others from being struck by vehicles, block off your work area
during installation or service.
4. Do not alter or modify any component or substitute components in this kit.
5. Warning! Substitution of components may impair intrinsic safety.
6. Field wiring to the Probe must be at least 50mm from any non-intrinsically safe device’s
wiring.
7. Warning! To prevent ignition of flammable or combustible atmospheres, disconnect battery
before servicing.
8. Before installing or taking the unit into a hazardous area, earth the unit in a safe area to
remove any static charge. Then immediately transport the unit to the installation site. Do
not rub or clean the unit prior to installation. Cleaning is not required under normal service
conditions. Do not rub or clean the unit after installation. If the unit is not fixed to a known
earth point when installed, ensure that a separate earth connection is made to prevent the
potential of a static discharge. When fitting or removing the unit, use of anti-static footwear
or clothing is required.
EXPLOSIVE
Fuels and their vapors are extremely explo-
sive if ignited.
FLAMMABLE
Fuels and their vapors are extremely flammable.
SLIPPERY
Curved metal tank surfaces can be extremely
slippery. Wear approved boots with slip
resistant soles.
FALLING OBJECTS
Being struck by even small objects falling from tall struc-
tures can result in severe injury or death. Wear your hard
hat at all times when working alongside tall structures.
POWER
To prevent ignition of flammable or combusti-
ble atmospheres, disconnect battery before
servicing.
WARNING
Heed the adjacent instructions to avoid damage to equip-
ment, property, environment or personal injury.
OFF
OFF

Introduction GENERAL PRECAUTIONS
5
GENERAL PRECAUTIONS
Heed service markings: Opening or removing the console cover may expose you to electric shock. Servicing of
Veeder-Root equipment must be done by Veeder-Root authorized service contractors.
Use product with approved equipment: This product should be used only with Veeder-Root components identified
as suitable for use with the MAG-XL Flex Probe.
Use the correct external power sources: This product should be operated only from the type of power sources
indicated on the electrical ratings labels affixed to the components. If you are not sure of the type of power source
required, consult your Veeder-Root authorized service contractor.
MAG-XL Flex Probe cable length: The length of the cable from its exit point in the tank riser or tank fitting to the
transmitter cannot exceed 10 feet.
Wet or below grade installations: Installation of this equipment in wet or below grade locations requires that the
installer take steps to ensure that the equipment is mounted above the maximum water level.
The MAG-XL Flex Probe insertion length is critical to ordering and installing the correct probe into the correct tank.
An improper probe length could result in the probe weight coming in contact with the tank bottom resulting in
inaccurate fuel height measurement and possible probe damage.
CAUTION! THE TRANSMITTER WILL NOT FUNCTION PROPERLY IN WATER. ALSO, SUBMERSION
OF THE TRANSMITTER IN WATER CAN CAUSE PERMANENT DAMAGE TO THE INTERNAL
ELECTRONICS.
SPECIAL TOOLS REQUIRED
• Strap wrench (5-inch pipe capacity minimum) • Wire strippers • Tape measure
• Small blade screwdriver (max. blade width 3/32”) • T-10/T-15 Torx drivers • Thread sealant or PTFE tape
General AST Guidelines
Above ground storage tanks (AST’s) are an essential element in the distribution of petroleum products. Refer to
the following organizations for applicable standards associated with AST’s:
• American Petroleum Institute (API) – www.api.org
• National Fire Protection Association (NFPA) – www.nfpa.org
• Occupational Safety and Health Administration (OSHA) - www.osha.gov
• Petroleum Equipment Institute (PEI) – www.pei.org
• Steel Tank Institute (STI) – www.steeltank.com
• Underwriters Laboratories (UL) – www.ul.com
SAFETY HARNESS
Injury or death resulting from falls while work-
ing on tall structures can be prevented by
wearing a 5-point harness that is tethered
securely by a shock absorbing lanyard to the
structure.
SAFETY BARRICADES
Unauthorized people or vehicles in the work area are dan-
gerous. Always use safety cones or barricades, safety
tape, and your vehicle to block the work area.
READ ALL RELATED MANUALS
Knowledge of all related procedures before
you begin work is important. Read and
understand all manuals thoroughly. If you do
not understand a procedure, ask someone
who does.

Introduction AST Construction Safe Work Practices
6
The above organizations may not address requirements imposed by individual jurisdictions. Each site owner must
ensure that contractors performing the work be knowledgeable of all applicable regulations. It is fully the
responsibility of the contractor, or employee performing the work, to abide by any and all additional Federal, State, or
local laws, regulations and manufacturer’s requirements that apply to the specific work being done. It is also the
responsibility of each contractor to ensure that subcontractors abide by all applicable safety requirements.
Construction related activities are covered by OSHA regulation 29 CFR 1926.
AST tanks must be properly grounded according to local codes and regulations.
AST Construction Safe Work Practices
Department of Labor rules for construction work practices are governed by OSHA as described in the Code of
Federal Regulations (CFR):
Title 29, Volume 8, Part 1926 - Safety and Health Regulations for Construction. Copies of these regulations are
available from OSHA’s web site located at 29 CFR 1926 (http:\\www.osha.gov). Most maintenance and other
operations are covered by OSHA 29 CFR 1910 (General Industry) regulations. These documents highlight many of
the Federal OSHA requirements that may apply to maintenance and construction work in the retail petroleum/
convenience business, but there is much more in the regulations than can be covered here. Some relevant
subsections are listed:
1910.66: Appendix C - Powered platforms, Man lifts, and Vehicle-Mounted Work Platforms
1910.23: Walking - Working surfaces - Guarding
1910.132: Personal Protective Equipment
Additional important information is available in the API publication: Safe Work Practices for Contractors
Working at Retail Petroleum/Convenience Facilities, API Recommended Practice 1646 First Edition, August
2006, Product No. A16461. For more Information about API Publications, Programs and Services, go to
www.api.org. The requirements and recommended practices contained in this document are the minimum safety
procedures with which everyone shall comply while working at a retail petroleum/convenience facility.
In addition, a task specific Job Safety Analysis shall be completed before any work may begin.
Personal Protective Equipment
The list below contains recommended clothing and protective equipment. Additional items may be advisable
depending on the job’s particular circumstances:
• 5-point safety harness
• 6-foot maximum, shock absorbing lanyard (ensure that there will be a support structure on top of the tank to which
you can secure the lanyard)
•Hardhat
• Safety Glasses
• Safety Footwear (ANSI Z41)
•Longpants
• Gloves - leather for materials handling, cut-resistant for sharp materials
• A heavy canvas bag with handles to hold tools and pre-assembled parts
Before you Begin
The instructions in this manual assume:
• The top of the tank has a 4” riser pipe, threaded to receive the riser cap and ring or a 2-inch threaded pipe fitting
to receive a 2” x 3/4”Adapter/Reducer. The recommended length of the 4-inch riser pipe or 2-inch pipe fitting

Introduction MAG-XL Flex Probe Operating Parameters
7
should be 10 inches, actual length dependent on probe insertion length.
IMPORTANT! The opening selected for the MAG-XL Flex Probe must be as far as possible from the
tank inlet piping.
• The TLS RF console and receiver are installed.
• The TLS console is installed. Note: the MAG-XL Flex Probe is only compatible with TLS Consoles installed with
Wireless 2 (2-Way) components supplied by V-R. The MAG-XL Flex Probe is for inventory only applications.
Leak detection is not available.
• You cannot mix Wireless 1 and Wireless 2 components on the same site or system. In each Wireless 2 System,
there is only one Receiver and one optional Repeater.
• The combination of the MAG-XL Flex Probe, XL Transmitter and the Battery Pack form an intrinsically safe
system and as such must be installed according to the instructions listed in this manual.
MAG-XL Flex Probe Operating Parameters
MAG-XL Flex Probe Limitations
MAG-XL Flex Probe Weights
Maximum Limits
Console Series
TLS-450/TLS-XB TLS4/8601 TLS-350 TLS-300 TLS2
Probe Length in Feet 54.5 54.5 54.5 54.5 32
Probe Length in Inches 654 654 654 654 384
Probe Length in Centime-
ters 1,661 1,661 1,661 1,661 975
Tank Volume in Gallons 2,641,720 2,641,720 999,999 999,999 260,000
Tank Volume in Litres 9,999,999 9,999,999 3,785,408 3,785,408 984,207
Maximum Number of Mag-
XL Probes per Console 32 12 16 2 or 4 6
Console Software Oldest
Compatible Version 1C 1 22 22 1
Weight Part Number Pounds Kilograms
889001-008 4.56 2.07
889001-009 6.38 2.89
889001-010 10.02 4.55
889001-011 12.75 5.79
889001-012 14.58 6.61
889001-013 16.40 7.44

Introduction National Electrical Code Compliance
8
National Electrical Code Compliance
The following information is for general reference and is not intended to replace recommended National Electric
Code (NEC) procedures. It is important for the installer to understand that electrical equipment and wiring located
in Class I, Division 1 and 2 installations shall comply with the latest appropriate articles found in the National
Electric Code (NFPA 70) and the Code for Motor Fuel Dispensing Facilities and Repair Garages (NFPA 30A), or
other local codes such as the CEC, Canadian Electrical Code.
AST tanks must be properly grounded according to NFPA 70 and applicable local codes and regulations.
MAG-XL FLEX PROBE WIRE LENGTH
Improper system operation could result in undetected potential environmental and health hazards if the MAG-XL
Flex Probe to TLS XL-Transmitter wire runs exceed 10 feet.
Veeder-Root Parts
• Veeder-Root MAG-XL Flex Probe, P/N 889111-XXX
• Veeder-Root Probe Components:
- 316 s.s. product float (2.05" dia., 0.54 sg, 350 psi), P/N 889001-001
- Weight Group (316 s.s. weight and 316 s.s. retaining pin)
• Veeder-Root MAG-XL Installation Kit (includes mounting hardware, transmitter and battery pack), P/N 858090-
202
• Optional 2-inch adapter/reducer (2” to 3/4”) kit (P/N 330020-666).
• Optional 4-inch riser cap and ring kit (P/N 330020-657).
Customer Supplied Parts
• Single-gang box from BELL outdoor, P/N 5321-0, or equivalent
• Single-gang blank cover from BELL outdoor, P/N 5173-0, or equivalent
• Galvanized threaded reducer bushing 3/4" to 1/2"
• Galvanized threaded 1/2” pipe, or 4” riser pipe, threaded to accept riser cap and ring

9
Example Drawings
Example MAG-XL Flex Probe Site Layout Drawing
Figure 1. Site drawing - example TLS RF wireless 2 system site layout – two Mag-XL Probes
LEGEND FOR NUMBERED BOXES IN Figure 1
To be installed in accordance with the National Electrical Code, NFPA
70 and the Code for Motor Fuel Dispensing Facilities and Repair Ga-
rages (NFPA 30A), or other local codes such as the CEC, Canadian
Electrical Code.
1. Battery Pack
2. TLS XL-Transmitter
3. Receiver
4. RS-485 Cable (Belden #3107A or equiv.)
5. TLS RF (Vm = 250 V)
6. Intrinsically safe wiring
7. TLS console (Vm = 250 V)
8. Conduit that enters power wiring knockouts
9. 120 or 230 Vac from power panel - separate branch circuits are
required for the TLS RF and TLS console.
10. Non-hazardous area
11. Hazardous area (Class I, Div. 1, Group D)
12. AST grounding cables and earth electrodes according to NFPA70
and local codes (ref. example in Figure 2).
13. Concrete tank pad.
ALARM
WARNING
POWER
4
2
1
7
3
9
972-1.eps
10 11
13
12
5
6
2
1
8

Example Drawings MAG-XL Flex Probe Dimensions
10
MAG-XL Flex Probe Dimensions
Figure 2. MAG-XL Flex Probe parameters
LEGEND FOR NUMBERED BOXES IN Figure 2
1. Insertion measuring point for 2-inch pipe cap installations (top
of pipe cab to tank bottom). (see table below)
2. Insertion measuring point for 4-inch riser pipe installations
(top of riser pipe to tank bottom). Add 2 inches (50.8 mm) for
brass ring/and riser cap. (see table below)
3. Null zone - typical all probes (see table below)
4. Measured insertion Length (see table below for probe form
number to order - always order smaller probe if measured
insertion length falls between two probes in table.
5. Clearance off bottom (see table below)
6. Weight length (see table below)
7. Dead zone (see table below)
8. Tank grounding bracket
9. Grounding cable
10. Concrete tank pad
11. Earth grounded electrode with cable bracket
972-9.eps
5
7
6
3
4
2
1
10
11
9
8

Example Drawings MAG-XL Flex Probe Dimensions
11
972-12.eps
NULL
ZONE
DEAD BAND
CLEAR-
ANCE
WEIGHT
GROUP
WEIGHT LENGTH
NULL
ZONE
DEAD BAND
CLEAR-
ANCE
WEIGHT
GROUP
WEIGHT LENGTH
(INCHES) (FEET) (INCHES) (INCHES) (INCHES) FORM NO. (INCHES) (INCHES) (FEET) (INCHES) (INCHES) (INCHES) FORM NO. (INCHES)
889111
—
02 4 144 12 ft. 12 6 889001-008 5 8 8 9 1 1 1
—
0 7 0 420 35 ft. 12 12 3 889001-010 11
889111
—
02 6 156 13 ft. 12 8 2
2
889001-009 7 8 8 9 1 1 1
—
0 7 1 426 35-1/2 ft. 12 12 3 889001-010 11
889111
—
02 8 168 14 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 7 2 432 36 ft. 12 12 3 889001-010 11
889111
—
03 0 180 15 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 7 3 438 36-1/2 ft. 12 15 4 889001-011 14
889111
—
03 2 192 16 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 7 4 444 37 ft. 12 15 4 889001-011 14
889111
—
03 4 204 17 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 7 5 450 37-1/2 ft. 12 15 4 889001-011 14
889111
—
03 6 216 18 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 7 6 456 38 ft. 12 15 4 889001-011 14
889111
—
03 8 228 19 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 7 7 462 38-1/2 ft. 12 15 4 889001-011 14
889111
—
04 0 240 20 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 7 8 468 39 ft. 12 15 4 889001-011 14
889111
—
04 2 252 21 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 7 9 474 39-1/2 ft. 12 15 4 889001-011 14
889111
—
04 4 264 22 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 8 0 480 40 ft. 12 15 4 889001-011 14
889111
—
04 6 276 23 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 8 1 486 40-1/2 ft. 12 15 4 889001-011 14
889111
—
04 8 288 24 ft. 12 8 2 889001-009 7 8 8 9 1 1 1
—
0 8 2 492 41 ft. 12 15 4 889001-011 14
889111
—
05 0 300 25 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 8 3 498 41-1/2 ft. 12 15 4 889001-011 14
889111
—
05 2 312 26 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 8 4 504 42 ft. 12 15 4 889001-011 14
889111
—
05 4 324 27 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 8 5 510 42-1/2 ft. 12 15 4 889001-011 14
889111
—
05 6 336 28 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 8 6 516 43 ft. 12 15 4 889001-011 14
889111
—
05 8 348 29 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 8 8 528 44 ft. 12 15 4 889001-011 14
889111
—
05 9 354 29-1/2 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 9 0 540 45 ft. 12 15 4 889001-011 14
889111
—
06 0 360 30 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 9 2 552 46 ft. 12 15 4 889001-011 14
889111
—
06 1 366 30-1/2 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 9 4 564 47 ft. 12 15 4 889001-011 14
889111
—
06 2 372 31 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 9 6 576 48 ft. 12 15 4 889001-011 14
889111
—
06 3 378 31-1/2 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
0 9 8 588 49 ft. 12 15 4 889001-011 14
889111
—
06 4 384 32 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
1 0 0 600 50 ft. 12 15 4 889001-011 14
889111
—
06 5 390 32.5 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
1 0 2 612 51 ft. 12 17 5 889001-012 16
889111
—
06 6 396 33 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
1 0 4 624 52 ft. 12 17 5 889001-012 16
889111
—
06 7 402 33.5 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
1 0 6 636 53 ft. 12 17 5 889001-012 16
889111
—
06 8 408 34 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
1 0 8 648 54 ft. 12 17 5 889001-012 16
889111
—
06 9 414 34.5 ft. 12 12 3 889001-010 11 8 8 9 1 1 1
—
1 0 9 654 54-1/2 ft. 12 17 5 889001-012 16
TOP MOUNTED DIGITAL MAG PROBE
INVENTORY ONLY - NO WATER DETECTION
MEASURED
INSERTION
LENGTH
FORM NO.
FORM NO.
MAG - XL
MEASURED
INSERTION
LENGTH
MAG - XL
756
347 56
34
Youcandetermine the insertionlength of a Mag-XL probe fromitsformnumber. Just multiply the formnumber suffix(-XXX) by 6 inches
to get the insertionlength. For example, the first probe inthe table, 889111-024, hasaninsertionlength of 144 inches(024 x6 = 144").
1 1
1
Table 1. MAG-XL Flex Probe Specifications

Example Drawings Example MAG-XL Flex Probe Installation in Tank Manway
12
Example MAG-XL Flex Probe Installation in Tank Manway
Figure 3. MAG-XL Flex Probe installation with riser pipe, top mounted in tank manway
LEGEND FOR NUMBERED BOXES IN Figure 3
1. Battery cable to MAG-XL transmitter
2. Battery pack
3. Brass 4” riser cap and ring (optional)
4. Weatherproof junction box (customer supplied)
5. 1/2” NPT galv. nipple and 3/4” to 1/2” reducing bushing (cus-
tomer supplied)
6. 1/2” NPT Brass adapter
7. TLS XL-Transmitter
8. 4” riser (Customer supplied - recommended riser length of 10”,
actual length dependent on probe insertion length)
9. MAG-XL Flex Probe Weight set a minimum distance above bot-
tom of tank (see Table 1).
10. Tank grounding (ref items 8 - 11 in Figure 2).
972-2b.eps
8
7
10
9
4
5
6
2
3
1

Example Drawings Example MAG-XL Flex Probe Installation in Existing Tank Opening
13
Example MAG-XL Flex Probe Installation in Existing Tank Opening
Figure 4. MAG-XL Flex Probe installation without riser pipe, top mounted in existing tank opening
LEGEND FOR NUMBERED BOXES IN Figure 3
1. Pipe cap with 3/4” NPT threaded opening (customer supplied)
2. Weatherproof junction box with 3/4” to 1/2” reducing bushing
in top opening (customer supplied)
3. Battery pack
4. 1/2” conduit, 6” minimum length, threaded both ends (cus-
tomer supplied)
5. 1/2” NPT Brass adapter
6. TLS XL-Transmitter
7. Battery cable
8. MAG-XL Flex Probe Weight set a minimum distance above bot-
tom of tank (see Table 1).
9. Tank grounding (ref items 8 - 11 in Figure 2).
972-2c.eps
8
456
2
1
3
7
9

Example Drawings Component Dimensions
14
Component Dimensions
Dimensions of the TLS XL-Transmitter and battery housing are shown in Figure 5.
Figure 5. Wireless component dimensions
LEGEND FOR NUMBERED BOXES IN Figure 5
1. TLS XL-Transmitter dimensions 2. Battery housing dimensions
972-6.eps
1
2
.513
(13.03mm)
W2
3.22
(81.79 mm)
3.52
(89.41 mm)
3.25
(82.55 mm)
3.81
(96.77 mm)
1.97
(50.03mm)
10.51
(266.9 mm)
3.52
(89.41 mm)
3.22
(81.79 mm)

15
MAG-XL Flex Probe Installation
Pre-Installation Component Setup and Functional Check
Follow the steps in the ‘Pre-Installation Component Setup and Functional Check’ section of the TLS RF Wireless 2
System (W2) Installation and Maintenance Guide (577013-964) to verify the Wireless System’s component
functionality.
Assemble the Battery Pack Mounting Bracket
PROBE INSTALLATION - MANWAY 4-INCH RISER PIPE
1. Connect the two 4-inch conduit hangers (item 1) from the installation kit to the battery mounting bracket (item
4) as shown in Figure 6.
2. Insert the bolt/nut pairs (items 2 and 3 in the figure) in each hanger as shown, but do not tighten.
3. Tighten the two bolt/nut pairs (items 2 and 5 in the figure) securing the mounting bracket to the conduit hang-
ers.
4. Get the customer supplied outdoor junction box. Get the customer supplied 3/4” x 1/2” reducing bushing.
Apply pipe thread sealant or PTFE tape to its threads and screw it into the top threaded opening of the junc-
tion box until tight.
5. Get the 1/2” nipple from the probe installation kit. Apply pipe thread sealant or PTFE tape to its threads and
screw it in the reducing bushing until tight.
6. Get the 1/2” brass hex adapter from the probe installation kit and after orienting the embossed arrow down,
apply pipe thread sealant or PTFE tape to its threads and screw it onto the 1/2” nipple until tight.
7. Take the battery support assembly, the junction box/conduit assembly and the transmitter to the top of the tank
for final assembly.
PROBE INSTALLATION - TOP OF TANK 2-INCH PIPE OPENING
1. Connect the two 2-inch conduit hangers (item 1) from the installation kit to the battery mounting bracket (item
4) as shown in Figure 6.
2. Insert the bolt/nut pairs (items 2 and 3 in the figure) in each hanger as shown, but do not tighten.
3. Tighten the two bolt/nut pairs (items 2 and 5 in the figure) securing the mounting bracket to the conduit hang-
ers.