Veeder-Root Mag Plus User manual

Mag Plus Density Probe
Manual No: 577013-987 ●Revision: D
Assembly Guide

Notice
Veeder-Root makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Veeder-Root shall not be liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this publication.
Veeder-Root reserves the right to change system options or features, or the information contained in this publication.
This publication contains proprietary information which is protected by copyright. All rights reserved. No part of this publication
may be photocopied, reproduced, or translated to another language without the prior written consent of Veeder-Root.
Contact TLS Systems Technical Support for additional troubleshooting information at 800-323-1799.
DAMAGE CLAIMS / LOST EQUIPMENT
Thoroughly examine all components and units as soon as they are received. If any cartons are damaged or missing, write a
complete and detailed description of the damage or shortage on the face of the freight bill. The carrier's agent must verify the
inspection and sign the description. Refuse only the damaged product, not the entire shipment.
Veeder-Root must be notified of any damages and/or shortages within 30 days of receipt of the shipment, as stated in our Terms
and Conditions.
VEEDER-ROOT’S PREFERRED CARRIER
1. Contact Veeder-Root Customer Service at 800-873-3313 with the specific part numbers and quantities that were missing
or received damaged.
2. Fax signed Bill of Lading (BOL) to Veeder-Root Customer Service at 800-234-5350.
3. Veeder-Root will file the claim with the carrier and replace the damaged/missing product at no charge to the customer.
Customer Service will work with production facility to have the replacement product shipped as soon as possible.
CUSTOMER’S PREFERRED CARRIER
1. It is the customer’s responsibility to file a claim with their carrier.
2. Customer may submit a replacement purchase order. Customer is responsible for all charges and freight associated with
replacement order. Customer Service will work with production facility to have the replacement product shipped as soon as
possible.
3. If “lost” equipment is delivered at a later date and is not needed, Veeder-Root will allow a Return to Stock without a restocking
fee.
4. Veeder-Root will NOT be responsible for any compensation when a customer chooses their own carrier.
RETURN SHIPPING
For the parts return procedure, please follow the appropriate instructions in the "General Returned Goods Policy” pages in the
"Policies and Literature" section of the Veeder-Root North American Environmental Products price list. Veeder-Root will not
accept any return product without a Return Goods Authorization (RGA) number clearly printed on the outside of the package.
©Veeder-Root 2013. All rights reserved.

Table of Contents
iii
Introduction
Important ...........................................................................................................................1
Contractor Certification Requirements ..............................................................................1
Related Manuals ...............................................................................................................1
Mag Plus Density Probe Installation Kits
Installation Kits ..................................................................................................................2
Assembling Probe Components
Attaching Probe Canister Insulator Sleeves (2-Inch Risers) .............................................4
Attaching Probe Canister Stabilizer Rings (3- & 4-Inch Risers) ........................................4
Assembling Floats onto Probe Shaft ................................................................................6
Attaching Cable Connector to Probe Canister ..................................................................6
Figures
Figure 1. Identifying Mag Plus Density Probe Installation Kit Components ...........3
Figure 2. Installing Probe Canister Insulator Sleeves ............................................4
Figure 3. Installing Probe Canister Spacer Rings ..................................................5
Figure 4. Example Installation of Density Probe Floats and Boot ............................6
Tables
Table 1. Installation Kit (with seal kit) - P/N 886002-XXX or P/N 886000-XXX .......2
Table 2. Installation Kit (without seal kit) - P/N 886001-XXX ..................................2
Table 3. Record of Installed Probe Float and Density Codes by Tank ....................7

1
Introduction
This manual describes how to identify and assemble the components of the Mag Plus Density Probes. Instructions
are included for assembling floats onto the probe’s shaft, attaching spacer rings to the probe’s canister, and
attaching the probe’s cable to the probe.
For guidelines on site preparation, instructions on installing the probe into a tank, and instructions on connecting
wiring from the probe to the console, you must refer to the appropriate Veeder-Root Site Preparation and
Installation manual.
For setup information, you must refer to the appropriate Veeder-Root Setup manual.
Important
Some of the installation kit components, such as epoxy packs, will be needed when installing the probe into the
tank. Do not discard any unused parts.
Make a record of the float size and Density Code that is installed on each probe. The installed float size and
Density Code will be required for each probe during system setup.
Contractor Certification Requirements
Veeder-Root requires the following minimum training certifications for contractors who will install and setup the
equipment discussed in this manual:
Installer (Level 1) Certification: Contractors holding valid Installer Certification are approved to perform wiring
and conduit routing; equipment mounting; probe, sensor and carbon canister vapor polisher installation; wireless
equipment installation; tank and line preparation; and line leak detector installation.
ATG Technician (Level 2/3 or 4) Certification: Contractors holding valid ATG Technician Certifications are
approved to perform installation checkout, startup, programming and operations training, system tests,
troubleshooting and servicing for all Veeder-Root Series Tank Monitoring Systems, including Line Leak Detection.
In addition, Contractors with the following sub-certification designations are approved to perform installation
checkout, startup, programming, system tests, troubleshooting, service techniques and operations training on the
designated system.
• Wireless 2
• Tall Tank
VR Vapor Products Certification: Contractors holding a certification with the following designations are
approved to perform installation checkout, startup, programming, system tests, troubleshooting, service techniques
and operations training on the designated system.
• ISD – In Station Diagnostics
• PMC – Pressure Management Control
• CCVP - Veeder-Root Vapor Polisher
• Wireless – ISD/PMC Wireless
• A current Veeder-Root Technician Certification is a prerequisite for the VR Vapor Products course.
Warranty Registrations may only be submitted by selected Distributors.
Related Manuals
After assemby, consult the appropriate Site Prep and Installation Manual for your console prior to installing the
probe in the tank.

2
Mag Plus Density Probe Installation Kits
Installation Kits
Available Mag Plus Density Probe installation kits are listed in Table 1 and Table 2. The kit components can be
identified in Figure 1.
Table 1. Installation Kit (with seal kit) - P/N 886002-XXX or P/N 886000-XXX
Qty. Description Part Number
1 Cable 330272-00X
1 Product Float 331XXX-001
1 Water /Density Float 33311X-00X
1 Boot 333202-001
2 Canister Spacers 332457-001 (2-inch riser),or
331555-001 (3 - 4-inch risers)
1 Cable Seal Kit 330020-121
Table 2. Installation Kit (without seal kit) - P/N 886001-XXX
Qty. Description Part Number
1 Cable 330272-00X
1 Product Float 331XXX-001
1 Water /Density Float 33311X-00X
1 Boot 333202-001
2 Canister Spacers 332457-001 (2-inch riser),or
331555-001 (3 - 4-inch risers)

Mag Plus Density Probe Installation Kits Installation Kits
3
Figure 1. Identifying Mag Plus Density Probe Installation Kit Components
BOOT
PRODUCT FLOAT
Cable
Probe cable connector
(attaches to threaded connector
on the top of probe canister)
Insulating Sleeves
(2-Inch Risers)
Adjustable Spacers
(3- and 4-Inch Risers)
987-1.eps
Wire nuts
Tie wraps
Epoxy
sealant
Cord Grip Fitting
Note: watch orientation
of bevels and tapers
when assembling these
cord grip components.
Body
Nut
Bushing
CABLE SEAL KIT COMPONENTS
(886002-XXX and 886000-XXX kits only)
WATER/DENSITY FLOAT
These two wires
connect in the J-box to
the two field wires from
the console
This
end
up
Density Code
etched along
this surface
(example)
B7053686719512
This
end
up
CANISTER SPACERS (Type depends on kit ordered)

4
Assembling Probe Components
Attaching Probe Canister Insulator Sleeves (2-Inch Risers)
1. Open the Probe shipping carton so that you have access to the probe. Also open the installation kit.
2. Install the two canister sleeves onto the probe canister as shown in Figure 2.
Figure 2. Installing Probe Canister Insulator Sleeves
Attaching Probe Canister Stabilizer Rings (3- & 4-Inch Risers)
1. Open the Probe shipping carton so that you have access to the probe. Open the installation kit.
2. Set the adjustable arms of the rings for a 3- or 4-inch riser (see Figure 3) as required. Install the two stabilizer
rings onto the probe canister as shown in the figure. Note: you must slide the bottom ring up over the probe
shaft and onto the lower end of the canister.
123
4
987-3.eps

Assembling Probe Components Attaching Probe Canister Stabilizer Rings (3- & 4-Inch Risers)
5
Figure 3. Installing Probe Canister Spacer Rings
Probe
canister
Up
Aftersetting arms (see insert) install top stabilizerring. Orient
locking tabs as shown, and thenslide ring overtop of canister
until tabs snap into groove incanister.
Afteradjustment (see insert) install bottomstabilizer
ring. Orient locking tabs as shown, and thenslide
ring up overprobe shaft and onto bottomof canister,
until tabs snap ingroove.
Probe shaft
set 4 arms of ring
as shown.
set 4 arms of ring
as shown.
OR
3-inch riser
4-inch riser
CANISTER STABILIZER RINGSETTINGS
987-2.eps

Assembling Probe Components Assembling Floats onto Probe Shaft
6
Assembling Floats onto Probe Shaft
All sizes of the Product and Water/Density Floats and the Boot are assembled on the probe shaft in the exact
sequence and orientation shown in Figure 4.
IMPORTANT! Failure to push the boot as far as possible onto the probe shaft could cause the boot and float(s) to
fall into the tank. The boot must be pushed on until it “locks” on the probe shaft.
Handle the probe carefully. Striking or dropping the probe will result in loss of calibration and could cause
permanent damage.
Figure 4. Example Installation of Density Probe Floats and Boot
Attaching Cable Connector to Probe Canister
1. Make a record of the float size and Density Code (see Figure 4) for each probe (you can record float data in
Table 3). This information will be needed during console configuration.
NOTE: If the Density Code is not available or is not entered into the console during configuration, the density
measured accuracy will default to ±2 kg/m3.
Bottomof
probe shaft
Up
Boot -
slide onprobe
shaft last
987-4.eps
Product float -
slide onprobe
shaft first.
Water/Density float -
slide onprobe
shaft second.
Density Code
etched along
this surface
(example)
B7053686719512

Assembling Probe Components Attaching Cable Connector to Probe Canister
7
2. Insert probe into the tank. Attach the existing cable connector to the threaded connector on top of the probe
canister and tighten down the integral nut.
3. Save the remaining kit components and refer to the appropriate Site Prep Manual to install the probe in the
tank and connect it to the field wiring from the console.
4. Refer to the appropriate console setup instructions to configure the Mag Plus Density Probe.
Jump back to Welcome.pd
Table 3. Record of Installed Probe Float and Density Codes by Tank
Tank/Product
Float
Size Density Code
1/
2/
3/
4/
5/
6/
7/
8/
9/
10/
11/
12/
13/
14/
15/
16/
4/Diesel 2-inch B7053686719512
Example

For technical support, sales or
other assistance, please visit:
www.veeder.com