Veeder-Root TLS2 Installation and operation manual

Manual No: 577013-983 ●Revision: B
Upgrade Guide
TLS2 to TLS2P

Notice
Veeder-Root makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Veeder-Root shall not be liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this publication.
Veeder-Root reserves the right to change system options or features, or the information contained in this publication.
This publication contains proprietary information which is protected by copyright. All rights reserved. No part of this publication
may be photocopied, reproduced, or translated to another language without the prior written consent of Veeder-Root.
Contact TLS Systems Technical Support for additional troubleshooting information at 800-323-1799.
DAMAGE CLAIMS / LOST EQUIPMENT
Thoroughly examine all components and units as soon as they are received. If any cartons are damaged or missing, write a
complete and detailed description of the damage or shortage on the face of the freight bill. The carrier's agent must verify the
inspection and sign the description. Refuse only the damaged product, not the entire shipment.
Veeder-Root must be notified of any damages and/or shortages within 30 days of receipt of the shipment, as stated in our Terms
and Conditions.
VEEDER-ROOT’S PREFERRED CARRIER
1. Contact Veeder-Root Customer Service at 800-873-3313 with the specific part numbers and quantities that were missing
or received damaged.
2. Fax signed Bill of Lading (BOL) to Veeder-Root Customer Service at 800-234-5350.
3. Veeder-Root will file the claim with the carrier and replace the damaged/missing product at no charge to the customer.
Customer Service will work with production facility to have the replacement product shipped as soon as possible.
CUSTOMER’S PREFERRED CARRIER
1. It is the customer’s responsibility to file a claim with their carrier.
2. Customer may submit a replacement purchase order. Customer is responsible for all charges and freight associated with
replacement order. Customer Service will work with production facility to have the replacement product shipped as soon as
possible.
3. If “lost” equipment is delivered at a later date and is not needed, Veeder-Root will allow a Return to Stock without a restocking
fee.
4. Veeder-Root will NOT be responsible for any compensation when a customer chooses their own carrier.
RETURN SHIPPING
For the parts return procedure, please follow the appropriate instructions in the "General Returned Goods Policy” pages in the
"Policies and Literature" section of the Veeder-Root North American Environmental Products price list. Veeder-Root will not
accept any return product without a Return Goods Authorization (RGA) number clearly printed on the outside of the package.
©Veeder-Root 2010. All rights reserved.

Table of Contents
iii
Introduction
Contractor Certification Requirements ..............................................................................1
Related Manuals ...............................................................................................................1
Safety Precautions ............................................................................................................2
Installation of Upgrade Kit
Kit required ........................................................................................................................3
Special tools required (not in kit) .......................................................................................3
Procedure ..........................................................................................................................3
Figures
Figure 1. Removing TLS2 Console Door ...............................................................3
Figure 2. Disconnecting the display assembly from the CPU board ......................4
Figure 3. Removing the display .............................................................................5
Figure 4. Attaching the new CPU board/inner door assembly to the console ........6
Figure 5. Attaching the display to the CPU board ..................................................7
Figure 6. Attaching the new door to the TLS2P console ........................................8
Figure 7. Securing outer door of TLS2P console ...................................................9

1
Introduction
This manual contains installation procedures for the TLS2 to TLS2P upgrade.
Contractor Certification Requirements
Veeder-Root requires the following minimum training certifications for contractors who will install and setup the
equipment discussed in this manual:
Installer (Level 1) Certification: Contractors holding valid Installer Certification are approved to perform wiring
and conduit routing; equipment mounting; probe, sensor and carbon canister vapor polisher installation; wireless
equipment installation; tank and line preparation; and line leak detector installation.
TLS-350 Technician (Level 2/3 or 4) Certification: Contractors holding valid TLS-350 Technician
Certifications are approved to perform installation checkout, startup, programming and operations training, system
tests, troubleshooting and servicing for all Veeder-Root TLS-300 or TLS-350 Series Tank Monitoring Systems,
including Line Leak Detection and associated accessories.
Warranty Registrations may only be submitted by selected distributors.
Related Manuals
577013-959 TLS2P Site Prep and Installation Manual
577013-960 TLS2P Setup & Operators Manual

Introduction Safety Precautions
2
Safety Precautions
The following safety symbols are used in this manual to alert you to important safety hazards and precautions.
EXPLOSIVE
Fuels and their vapors are extremely
explosive if ignited.
FLAMMABLE
Fuels and their vapors are extremely
flammable.
ELECTRICITY
High voltage exists in, and is supplied
to, the device. A potential shock hazard
exists.
TURN ELECTICAL POWER OFF
Live power to a device creates a
potential shock hazard. Turn Off electri-
cal power to the device and associated
accessories when servicing the unit.
WARNING
Heed the adjacent instructions to avoid
damage to equipment, property, envi-
ronment or personal injury.
STATIC SENSITIVE COMPO-
NENTS
Wear grounded anti-static wrist strap
before handling the printed circuit
board.
READ ALL RELATED MANUALS
Knowledge of all related procedures
before you begin work is important.
Read and understand all manuals thor-
oughly. If you do not understand a pro-
cedure, ask someone who does.
WARNING
FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY PRECAUTIONS
COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, RESULTING IN SERIOUS
INJURY OR DEATH.
You are working with a device in which potentially lethal voltages may be present.
Death or injury may result if safety precautions are not followed.
1. Turn off, tag, and lockout power to the console before installing this kit.
2. Read all instructions and symbol warnings.
OFF
OFF

3
Installation of Upgrade Kit
This section describes the field upgrade of a TLS2 into a TLS2P Console.
KIT REQUIRED
•TLS2TO TLS2P Upgrade kit - P/N 330020-662
SPECIAL TOOLS REQUIRED (NOT IN KIT)
• Torx drive screwdrivers to fit #T-10 and #T-15 screws
PROCEDURE
Figure 1. Removing TLS2 Console Door
983-1.eps
2
3
1
1
2
Shut off, tag, and lockout power to the TLS2
Console.
1 Remove and retain the top and bottom T-15 shoulder
screws and washers from the right side of the console
door (item 2 in Figure 1). Swing the door to the left.
2 Loosen the T-15 screw in the door grounding saddle
clamp and remove the ground wire (item 3 in Figure 1).

Installation of Upgrade Kit Safety Precautions
4
Figure 2. Disconnecting the display assembly from the CPU board
983-2.eps
1
1
22
1 Remove and retain the four T-10 screws, spacersand
washers(items1 and 2 in Figure 2) attaching the
display to the CPU board. Retain the two shorter
screws(0.5” long - item 2 in Figure 2) and all of the
washers. Carefully remove the last screw while
holding the display assembly. Lower the display until
it issupported by itstwo cables.

Installation of Upgrade Kit Safety Precautions
5
Figure 3. Removing the display
983-3.eps
2
1
3
4
1 Hold the display and pull up the ribbon cable from its
connector on the CPU board (item 1 in Figure 3) and
remove the 2-wire plug (item 2 in Figure 3) at the top
of the CPU board. Carefully set the display aside.
2 Using the T-15 torx wrench, remove the ground wire
saddle clamp on the inner door (item 3 in Figure 3).
3 Remove the ribbon cable from its connector on the
edge of the CPU board (item 4 in Figure 3). Notice the
orientation of the ribbon cable in the connector as it will
connect to the new CPU board in the same way.
4 Remove and retain the top and bottom T-15 screws
and washers (item 1 in Figure 1) from the left side of
the console door. Remove and discard the door.
5 While pushing the ground wire and ribbon cable
through the slot in the inner door, remove the CPU
board/inner door assembly and discard.

Installation of Upgrade Kit Safety Precautions
6
Figure 4. Attaching the new CPU board/inner door assembly to the console
983-4.eps
1
1
2
3
1 Get the new TLS2P CPU board/inner door assembly
from the kit. Get the two T-15 torx shoulder screws
you removed from the right side of the door earlier.
2 Get the static protecting wrist strap from the kit and slip
the looped end around one wrist and connect the other
end to side of the console.
3 Remove the CPU board/inner door assembly from its
packing and push the ground cable and ribbon cable
through the right side opening in the inner door
assembly and place the inner door assembly on the
console and screw in the two right-side T-15 torx
shoulder screws (item 1 in Figure 4), snug but not tight.
Reattach the grounding strap to the bare metal on the
top of the inner door.
4 Loosen the ground wire saddle clamp on the inner door
(item 2 in Figure 4) and loop the ground wire through it
and tighten securely (see photo at right). The other end
of the ground wire will attach to the new door’s
grounding saddle clamp.
5 Connect the ribbon cable (item 3 in Figure 4) to the
connector on the left side of the new CPU board.

Installation of Upgrade Kit Safety Precautions
7
Figure 5. Attaching the display to the CPU board
983-5.eps
1
3
3
2
3
3
1 Get the four T-10 screws, spacersand washersyou
saved when removing the display from the old CPU
board (items1 and 2 in Figure 2).
2Get the display and attach its2-wire cable plug to the
connector on the CPU board (item 1 in Figure 5).
3 Push the display’s ribbon cable into its connector on
the CPU board (item 2 in Figure 5).
4 Position the display over the standoffs (item 3 in
Figure 5) and replace the 4 screws and 2 spacers
(used under right side display attaching screws only -
see plastic spacers (item 4 in photo at right).
4
4

Installation of Upgrade Kit Safety Precautions
8
Figure 6. Attaching the new door to the TLS2P console
983-7.eps
1
1
2
1 Get the two T-15 torx shoulder screwsand the new
TLS2P door.
2 Position the door over the left holes in the top and
bottom of the console and screw in the two shoulder
screws (item 1 in Figure 6).
3 Loosen the grounding clamp (item 2 in Figure 6) in the
door and push the grounding strap from the console
under the saddle clamp and tighten the screw.

Installation of Upgrade Kit Safety Precautions
9
Figure 7. Securing outer door of TLS2P console
983-8.eps
1
1
1Remove the static preventing grounding strap from the
inner door. Remove the two right T-15 torx screws
holding on the inner door (item 1 Figure 6), close the
new outer door, reinsert the two shoulder screws in the
two holes in the door and tighten securely.
2 Restore power to the TLS2P console and refer to
manual 577013-960 for setup procedures.

For technical support, sales or
other assistance, please visit:
www.veeder.com