Velbus VMBSTART1W User manual

5 TROUBLESHOOTING
If something doesn’t work out as expected, first carefully check the wiring,
make sure the terminators are set as described above, and power cycle
theinstallation.
If this doesn’t solve your problem, please refer to the support pages
on www.velbus.eu, or contact your dealer.
6 MORE INFORMATION
The Velbus Installation Guide is a complete, detailed manual on Velbus
hardware (Part 1) and programming (Part 2).
Download it for free on www.velbus.eu.
On our website you will also find our product catalogue, product specifications,
an FAQ section, downloads, points of sale, and much more.
GETTING STARTED WITH VELBUS
4 EXTRA
To change the text on the oled screen, select the VMBGPOD module in
Velbuslink and click on the gear icon.
In the Configuration window, click on the “edit bitmap” button
and add names and icons:
In the Configuration window, you can find a lot of other settings concerning
feedback lights, navigation, screensaver settings etc. Don’t forget to sync
(writethe changes to the modules) before testing the changes you made.
www.velbus.eu
3 PROGRAM THE MODULES (continuation)
9. Press the “Synchronize” button. In the “Synchronize Project” dialog,
make sure “Only write changes” is checked, and press “Write”
When the writing has finished (this should take only a few seconds),
you can now operate Relay 1 (“Light kitchen”) by pressing the upper left
touch button (Channel 1) of the glass control module.

3 PROGRAM THE MODULES
You can find complete instructions on how to program Velbus modules in theVelbus
Installation Guide Part 2: Programming (free download on velbus.eu).
To get you started, here’s how to program an on/off switch:
1. Connect your PC with the Velbus configuration module
using the included USB cable.
2. Download, install and start Velbuslink, the free configuration software for
Velbus. (http://www..eu/link).
3. Click on “New” (upper left corner)
to start the “New project wizard”.
4. Follow the wizard by clicking on “Next” until you get the message “Your project
has been created successfully”.
5. In the navigation window, fold open
the VMBGPOD and the VMB4RYNO modules
by clicking on the “+” signs next
to their names.
6. (Optional) Left-click on the name of a selected module or channel
to change it. Eg. change “Relay 1” to “Light kitchen”
7. Drag “Button 1” and drop it on relay 1 (“Light kitchen”)
8. In the dialog that opens, select “Toggle” and press “OK”
2 SET
THETERMINATORS
Most Velbus modules have a
terminator (jumper or switch) that
by factory default is open. In a
standard Velbus installation exactly
two of these terminators have to be
closed, with as much distance (wire)
between them as possible.
For DIN-rail modules open the
front cover plate (see image below)
to find the terminator. For other
modules, you will find it at the back
of the module.
If the terminator is a jumper,
place it over the two “TERM” pins
(seeimagebelow) to close it. If it is
a switch, set it to the “ON” position.
1 INSTALL THEHARDWARE
Connect all the modules using the included VMBRAIL-R interconnection rail and a 4-wired bus cable
(not included, we recommend EIB or FTP).
VMBGPOD
Control
module
Add input modules,
buttons, sensors, etc.,
to complete
theinstallation
VMB4RYLD
Relay
module
VMBRSUSB
Configuration
module
VMBSMPS
Power
supply
230 VAC
N L
L N
230 VAC
Add more
modules to
complete
theinstallation
Add more
modules to
complete
theinstallation
drag and drop

3 PROGRAM THE MODULES
You can find complete instructions on how to program Velbus modules in theVelbus
Installation Guide Part 2: Programming (free download on velbus.eu).
To get you started, here’s how to program an on/off switch:
1. Connect your PC with the Velbus configuration module
using the included USB cable.
2. Download, install and start Velbuslink, the free configuration software for
Velbus. (http://www..eu/link).
3. Click on “New” (upper left corner)
to start the “New project wizard”.
4. Follow the wizard by clicking on “Next” until you get the message “Your project
has been created successfully”.
5. In the navigation window, fold open
the VMBGPOD and the VMB4RYNO modules
by clicking on the “+” signs next
to their names.
6. (Optional) Left-click on the name of a selected module or channel
to change it. Eg. change “Relay 1” to “Light kitchen”
7. Drag “Button 1” and drop it on relay 1 (“Light kitchen”)
8. In the dialog that opens, select “Toggle” and press “OK”
2 SET
THETERMINATORS
Most Velbus modules have a
terminator (jumper or switch) that
by factory default is open. In a
standard Velbus installation exactly
two of these terminators have to be
closed, with as much distance (wire)
between them as possible.
For DIN-rail modules open the
front cover plate (see image below)
to find the terminator. For other
modules, you will find it at the back
of the module.
If the terminator is a jumper,
place it over the two “TERM” pins
(seeimagebelow) to close it. If it is
a switch, set it to the “ON” position.
1 INSTALL THEHARDWARE
Connect all the modules using the included VMBRAIL-R interconnection rail and a 4-wired bus cable
(not included, we recommend EIB or FTP).
VMBGPOD
Control
module
Add input modules,
buttons, sensors, etc.,
to complete
theinstallation
VMB4RYLD
Relay
module
VMBRSUSB
Configuration
module
VMBSMPS
Power
supply
230 VAC
N L
L N
230 VAC
Add more
modules to
complete
theinstallation
Add more
modules to
complete
theinstallation
drag and drop

3 PROGRAM THE MODULES
You can find complete instructions on how to program Velbus modules in theVelbus
Installation Guide Part 2: Programming (free download on velbus.eu).
To get you started, here’s how to program an on/off switch:
1. Connect your PC with the Velbus configuration module
using the included USB cable.
2. Download, install and start Velbuslink, the free configuration software for
Velbus. (http://www..eu/link).
3. Click on “New” (upper left corner)
to start the “New project wizard”.
4. Follow the wizard by clicking on “Next” until you get the message “Your project
has been created successfully”.
5. In the navigation window, fold open
the VMBGPOD and the VMB4RYNO modules
by clicking on the “+” signs next
to their names.
6. (Optional) Left-click on the name of a selected module or channel
to change it. Eg. change “Relay 1” to “Light kitchen”
7. Drag “Button 1” and drop it on relay 1 (“Light kitchen”)
8. In the dialog that opens, select “Toggle” and press “OK”
2 SET
THETERMINATORS
Most Velbus modules have a
terminator (jumper or switch) that
by factory default is open. In a
standard Velbus installation exactly
two of these terminators have to be
closed, with as much distance (wire)
between them as possible.
For DIN-rail modules open the
front cover plate (see image below)
to find the terminator. For other
modules, you will find it at the back
of the module.
If the terminator is a jumper,
place it over the two “TERM” pins
(seeimagebelow) to close it. If it is
a switch, set it to the “ON” position.
1 INSTALL THEHARDWARE
Connect all the modules using the included VMBRAIL-R interconnection rail and a 4-wired bus cable
(not included, we recommend EIB or FTP).
VMBGPOD
Control
module
Add input modules,
buttons, sensors, etc.,
to complete
theinstallation
VMB4RYLD
Relay
module
VMBRSUSB
Configuration
module
VMBSMPS
Power
supply
230 VAC
N L
L N
230 VAC
Add more
modules to
complete
theinstallation
Add more
modules to
complete
theinstallation
drag and drop

3 PROGRAM THE MODULES
You can find complete instructions on how to program Velbus modules in theVelbus
Installation Guide Part 2: Programming (free download on velbus.eu).
To get you started, here’s how to program an on/off switch:
1. Connect your PC with the Velbus configuration module
using the included USB cable.
2. Download, install and start Velbuslink, the free configuration software for
Velbus. (http://www..eu/link).
3. Click on “New” (upper left corner)
to start the “New project wizard”.
4. Follow the wizard by clicking on “Next” until you get the message “Your project
has been created successfully”.
5. In the navigation window, fold open
the VMBGPOD and the VMB4RYNO modules
by clicking on the “+” signs next
to their names.
6. (Optional) Left-click on the name of a selected module or channel
to change it. Eg. change “Relay 1” to “Light kitchen”
7. Drag “Button 1” and drop it on relay 1 (“Light kitchen”)
8. In the dialog that opens, select “Toggle” and press “OK”
2 SET
THETERMINATORS
Most Velbus modules have a
terminator (jumper or switch) that
by factory default is open. In a
standard Velbus installation exactly
two of these terminators have to be
closed, with as much distance (wire)
between them as possible.
For DIN-rail modules open the
front cover plate (see image below)
to find the terminator. For other
modules, you will find it at the back
of the module.
If the terminator is a jumper,
place it over the two “TERM” pins
(seeimagebelow) to close it. If it is
a switch, set it to the “ON” position.
1 INSTALL THEHARDWARE
Connect all the modules using the included VMBRAIL-R interconnection rail and a 4-wired bus cable
(not included, we recommend EIB or FTP).
VMBGPOD
Control
module
Add input modules,
buttons, sensors, etc.,
to complete
theinstallation
VMB4RYLD
Relay
module
VMBRSUSB
Configuration
module
VMBSMPS
Power
supply
230 VAC
N L
L N
230 VAC
Add more
modules to
complete
theinstallation
Add more
modules to
complete
theinstallation
drag and drop

5 TROUBLESHOOTING
If something doesn’t work out as expected, first carefully check the wiring,
make sure the terminators are set as described above, and power cycle
theinstallation.
If this doesn’t solve your problem, please refer to the support pages
on www.velbus.eu, or contact your dealer.
6 MORE INFORMATION
The Velbus Installation Guide is a complete, detailed manual on Velbus
hardware (Part 1) and programming (Part 2).
Download it for free on www.velbus.eu.
On our website you will also find our product catalogue, product specifications,
an FAQ section, downloads, points of sale, and much more.
GETTING STARTED WITH VELBUS
4 EXTRA
To change the text on the oled screen, select the VMBGPOD module in
Velbuslink and click on the gear icon.
In the Configuration window, click on the “edit bitmap” button
and add names and icons:
In the Configuration window, you can find a lot of other settings concerning
feedback lights, navigation, screensaver settings etc. Don’t forget to sync
(writethe changes to the modules) before testing the changes you made.
www.velbus.eu
3 PROGRAM THE MODULES (continuation)
9. Press the “Synchronize” button. In the “Synchronize Project” dialog,
make sure “Only write changes” is checked, and press “Write”
When the writing has finished (this should take only a few seconds),
you can now operate Relay 1 (“Light kitchen”) by pressing the upper left
touch button (Channel 1) of the glass control module.

5 TROUBLESHOOTING
If something doesn’t work out as expected, first carefully check the wiring,
make sure the terminators are set as described above, and power cycle
theinstallation.
If this doesn’t solve your problem, please refer to the support pages
on www.velbus.eu, or contact your dealer.
6 MORE INFORMATION
The Velbus Installation Guide is a complete, detailed manual on Velbus
hardware (Part 1) and programming (Part 2).
Download it for free on www.velbus.eu.
On our website you will also find our product catalogue, product specifications,
an FAQ section, downloads, points of sale, and much more.
GETTING STARTED WITH VELBUS
4 EXTRA
To change the text on the oled screen, select the VMBGPOD module in
Velbuslink and click on the gear icon.
In the Configuration window, click on the “edit bitmap” button
and add names and icons:
In the Configuration window, you can find a lot of other settings concerning
feedback lights, navigation, screensaver settings etc. Don’t forget to sync
(writethe changes to the modules) before testing the changes you made.
www.velbus.eu
3 PROGRAM THE MODULES (continuation)
9. Press the “Synchronize” button. In the “Synchronize Project” dialog,
make sure “Only write changes” is checked, and press “Write”
When the writing has finished (this should take only a few seconds),
you can now operate Relay 1 (“Light kitchen”) by pressing the upper left
touch button (Channel 1) of the glass control module.

5 TROUBLESHOOTING
If something doesn’t work out as expected, first carefully check the wiring,
make sure the terminators are set as described above, and power cycle
theinstallation.
If this doesn’t solve your problem, please refer to the support pages
on www.velbus.eu, or contact your dealer.
6 MORE INFORMATION
The Velbus Installation Guide is a complete, detailed manual on Velbus
hardware (Part 1) and programming (Part 2).
Download it for free on www.velbus.eu.
On our website you will also find our product catalogue, product specifications,
an FAQ section, downloads, points of sale, and much more.
GETTING STARTED WITH VELBUS
4 EXTRA
To change the text on the oled screen, select the VMBGPOD module in
Velbuslink and click on the gear icon.
In the Configuration window, click on the “edit bitmap” button
and add names and icons:
In the Configuration window, you can find a lot of other settings concerning
feedback lights, navigation, screensaver settings etc. Don’t forget to sync
(writethe changes to the modules) before testing the changes you made.
www.velbus.eu
3 PROGRAM THE MODULES (continuation)
9. Press the “Synchronize” button. In the “Synchronize Project” dialog,
make sure “Only write changes” is checked, and press “Write”
When the writing has finished (this should take only a few seconds),
you can now operate Relay 1 (“Light kitchen”) by pressing the upper left
touch button (Channel 1) of the glass control module.