Velocity Velocity Bookcase 900 High VBC99 User manual

MANUFACTURER CODE: VBC99
OW CODES: CPVELBCWH, CPVELBC90B,
CPVELBCGB, CPVELBCGR, CPVELBC90W
Assembly Instructions
Velocity Bookcase
900 High
2 CARTONS
1 / 5
NOTE: The Velocity Bookcase converts to a Storage Cupboard by adding doors
(box 3). If you have ordered a Storage Cupboard additional instructions and
hardware are located in box 3.
manufactured by designtec
www.designtec.com.au

NOTE
Please check you have all hardware before assembling.
If you are missing any hardware, please contact the store of purchase.
Please ensure you have the name of the item, required hardware part and quantity.
Please retain your receipt as proof of purchase to validate your warranty.
CAUTION
Do not tighten screws before all screws are in the right place.
Do not use this product unless all bolts, screw and knobs are firmly secured.
Check that all bolts, screws and knobs are securely tightened at least every 4 months.
WARNING
If parts are missing, broken, damaged or worn stop using the product until all repairs
are made using manufacturer authorised parts.
Failure to follow these warnings could result in serious injury.
HARDWARE INCLUDED
Note - Individual hardware images are not to scale.
A & B - TWO PART FOOT
PRE-INSERTED HARDWARE
CAM HOUSING
x 14
C - PIN
TOOLS REQUIRED FOR ASSEMBLY
1 x Philips Head Screwdriver
2 / 5
(A)
(B)
x 4
D - 16mm SCREW
x 16
x 8
E - CONFIRMAT SCREW F - SHELF SUPPORT
x 8

STEP 1
Unscrew the two part foot to separate PART (A) from PART (B).
Fix PART (A) of two part foot to the bookcase base using SCREW (D).
PART (B) of the two part foot can now be attached to PART (A) by placing it on top and
rotating clockwise.
3 / 5
(D)(A)
(B)
STEP 2
Fix four (4) PINS (C) into the outer pre-drilled holes on the end panels with your
screwdriver.
NOTE: these pre-drilled holes are slightly offset to the edge.
(C)
LH END
RH END
BASE

STEP 3
Fix ten (10) PINS (C) into back panel as shown below.
NOTE: all pre-drilled holes for the PINS (C) are offset to the edge of the panel.
Ensure to leave all central pre-drilled holes empty.
STEP 4
Attach the end panels to the
back panel by aligning the
PINS (C) with the pre-inserted
CAM HOUSING. To tighten,
use your screw-driver and
rotate the screw on the CAM
HOUSING to the right.
4 / 5
(C)
BACK PANEL
STEP 5
Fix the bookcase top to the back &
ends by aligning the PINS (C) with the
pre-inserted CAM HOUSING and
tighten by rotating the CAM HOUSING
screw to the right using your
screwdriver.
CAM HOUSING
LH END
BACK PANEL
RH END
TOP

STEP 6
Take your bookcase base and align with the back, top and sides of your bookcase.
Place eight (8) CONFIRMAT SCREWS (E) through the pre-drilled holes on the underside
of the base. Using your screw driver, tighten all CONFIRMAT SCREWS (E) until base is
secure.
TIP: On un-even floor the two part foot can be adjusted out to level the bookcase.
5/ 5
NOTE: IF YOU HAVE ORDERED A STORAGE CUPBOARD, HARDWARE AND
INSTRUCTIONS FOR THE ATTACHMENT OF DOORS ARE IN BOX 3 OF 3.
STEP 7
To insert shelves, place your SHELF
SUPPORTS (F) in the holes on the
end panels at the desired shelf
height and the shelf sits on top
(F)