Velocity VR96 User manual

MANUFACTURER CODES: VR96
OW CODES: CPVELRETGR, CPVELR90BW,
CPVELRETWH, CPVELR90WI
Assembly Instructions
Velocity Desk Return (Universal)
1 CARTON
1 / 6
manufactured by designtec
www.designtec.com.au

NOTE
Please check you have all hardware before assembling.
If you are missing any hardware, please contact the store of purchase.
Please ensure you have the name of the item, required hardware part and quantity.
Please retain your receipt as proof of purchase to validate your warranty.
CAUTION
Do not tighten screws before all screws are in the right place.
Do not use this product unless all bolts, screw and knobs are firmly secured.
Check that all bolts, screws and knobs are securely tightened at least every 4 months.
WARNING
If parts are missing, broken, damaged or worn stop using the product until all repairs
are made using manufacturer authorised parts.
Failure to follow these warnings could result in serious injury.
HARDWARE INCLUDED
Note - Individual hardware images are not to scale.
A - ADJUSTABLE FOOT B - PIN
x 7
PRE-INSERTED HARDWARE
CAM HOUSING
TOOLS REQUIRED FOR ASSEMBLY
1 x Philips Head Screwdriver
2 / 6
x 2
C - JOINING PLATE
x 1
D - 17mm SCREW
x 8
E -32mm SCREW
x 3

STEP 1
Insert three (3) PINS (B) into pre-drilled holes on end panel.
Then insert two (2) ADJUSTABLE FEET (A) into the pre-inserted threaded sleeve.
(A)
3 / 6
STEP 2 Insert four (4) PINS (B) into pre-drilled holes on your modesty panel.
(B)
IMPORTANT NOTE: This return is universal so can be used on the
Left Hand Side (LHS) or Right Hand Side (RHS) of your Velocity Desk.
For a LHS return, see below pages 3-4.
For a RHS return, see pages 5-6.
(B)
MODESTY
PANEL
(B)
END PANEL
(A)

4 / 6
(C) (D)
TOP
END PANEL
MODESTY
PANEL
STEP 3 Align the PINS (B) on your modesty panel with the CAM HOUSING on the
END PANEL, tighten by rotating the screw to the right hand side with your screw
driver.
Then align PINS on the modesty and end panel with the CAM HOUSING on the
TOP PANEL and tighten by rotating the screw to the right hand side with your
screw driver.
STEP 4
Attach your JOINING PLATE (C) with four (4) SCREWS (D) using your screwdriver.
Noting that one half of the joining plate will over hang the top, allowing it to be
attached to the underside of your Velocity Desk.
NOTE: There will be pre-drilled holes under the top of your Velocity Desk to allow
for easy attachment, use the remaining four (4) SCREWS (D) and secure with a
screw driver.
Three (3) extra screws (E) have been supplied to join your modesty panel with your
Velocity Desk end if extra support is needed.
CAM HOUSING

5 / 6
(A)
(B)
STEP 2
Insert four (4) PINS (B) into pre-drilled holes on your modesty panel.
(B)
STEPS FOR USING AS A RIGHT HAND SIDE RETURN:
END PANEL
MODESTY
PANEL
STEP 1
Insert three (3) PINS (B) into pre-drilled holes on end panel.
Then insert two (2) ADJUSTABLE FEET (A) into the pre-inserted threaded sleeve.

6 / 6
STEP 3 Align the PINS (B) on your modesty panel with the CAM HOUSING on the
END PANEL, tighten by rotating the screw to the right hand side with your screw
driver.
Then align PINS on the modesty and end panel with the CAM HOUSING on the
TOP PANEL and tighten by rotating the screw to the right hand side with your
screw driver.
(C)
(D)
MODESTY
PANEL
TOP
END PANEL
STEP 4
Attach your JOINING PLATE (C) with four (4) SCREWS (D) using your screwdriver.
Noting that one half of the joining plate will over hang the top, allowing it to be
attached to the underside of your Velocity Desk.
NOTE: There will be pre-drilled holes under the top of your Velocity Desk to allow
for easy attachment, use the remaining four (4) SCREWS (D) and secure with a
screw driver.
Three (3) extra screws (E) have been supplied to join your modesty panel with your
Velocity Desk end if extra support is needed.