VENTRA RVC -1XC433 User manual

RVC -1XC433 Rear View Camera Kit
Specification:
Parts included:
•EX4-XC4 Outdoor Color Camera w/ IR x 1
•EX4-CBL33 60ft 4 in DIN cable x 1
•RVC-PIG DIN to RCA / Power Cable x 1
Ventra Technology Inc. Covina, CA.USA www.ventrainc.com [e-mail] Tel: [phone]
Camera
Chi set 1/3” CMOS
Camera Lens 2.8mm
Resolution 650 TVL
Camera Angle 120 degrees (D) / 90 degrees (H)
Camera Rating IP66 Outdoor Rated
IR LED 9 LED
Illumination 0 Lux – IR on
S/N ration >45db
Electronic Shutter 1/60 ~ 100,000
Auto Gain Control Auto
Back Light Com ensation Auto
White Balance Auto
TV System NTSC
Camera Power DC12V ~ 24V 125mA
Humidity <90%
Tem erature Range –O erating -4F ~ 150F ( -20C ~ +65C)
Cable
Environment Indoor
Pin 4 Pins (Video, Audio and Power)
InstallationGuide
1. Determine the location and mounting osition of the camera rior to installation
2. Test the viewing angle by owering both the camera and monitor before ermanently securing the camera
3. Once location is determined, securely affix mounting bracket of the camera to the vehicle
4. Connect the EX4-XC camera to EX4-CBL 4 in DIN cable. Ensure the cable is securely connected (see diagram below)
5. Connect the EX4-CBL cable to RVC-PIG DIN to RCA / Power cable
6 RVC-PIG:
- 2 ower igtail wire (Red = 12V Positive, Black = Ground) to a ower source (i.e. tail light, reverse light, turn signal
or vehicle fuse)
- DC ower lug to EX4-XC camera
- RCA connection to monitor via RCA cable
7. Secure RCA cable connection by a lying heat shrink tube or electrical ta e
8. Connect the RCA cable into the LCD screen
Warning:
Install equi ment only when vehicle is safely arked, leveled and ower Off
View and access the monitor only when safe to do so
Review surrounding before o erating / moving vehicle
Observe all electrical safety guideline and olarity to avoid injury
Please consult with Vehicle Manufacturer for warranty and settings rior to installation
Ventra is not res onsible for any warranty ertaining to the vehicle
V. 07 18

RVC -1XC433 Rear View Camera Kit
Ventra Technology Inc. Covina, CA.USA www.ventrainc.com [e-mail] Tel: [phone]
Installation layout
System Operation
•Ensure the camera in ut (RCA) is connected to the vehicle’s monitor in ut
•Additional settings in the vehicle may be required to activate video in ut. Please check the vehicle owners manual or consult with vehicle
factory certified technician for additional information
•As each vehicle manufacturer incor orates its own settings, Ventra does not rovide su ort on the setting and configuration ertaining to
the individual make and model of vehicle
•Ventra is not res onsible for any warranty issues or claims ertaining to the vehicle. Please consult with vehicle manufacturer rior to any
installation
Existing Monitor
OR
Secure cable connection by a lying
heat shrink tube or electrical ta e to
minimize movement from vehicle
vibration
EX4-CBL cable is not water roof and
should not be ex osed to direct sunlight,
rain or element. Cable should be laced
in weather roof conduit or sleeve
Operation Guide:
1. VLCD-7 monitor su orts dual video in ut. If only 1 camera is connected, that camera will be rimary, regardless of which in ut it is connected to
2. If connecting 2 cameras,
•Input 2 = Primary Camera
•Input 1 = Secondary Camera
3. To switch camera view, Press for momentary view of the second camera, Or if the secondary camera was owered on / triggered
by a switch (i.e. turn signal). Monitor will auto revert back to the rimary camera after a roximately 5 seconds.
VLCD-7 Operation ( If connecting to Ventra VLCD Monitor):
1. Press SET key to Enter or Exit Menu
2. Press or to navigate menu. Press or to change setting