VENTRA RVM-1XC433 User manual

RVM -1XC433 Rear View Camera Kit
Specification:
Parts included:
•EX4-XC4 Outdoor Color Camera w/ IR x 1
•VLCD-7 7” LCD creen x 1
•EX4-CBL33 33ft 4 pin DIN cable x 1
•RVC-PIG DIN to RCA / Power Cable x 1
Ventra Technology Inc. Covina, CA. U A www.ventrainc.com [e-mail] Tel: [phone]
Camera
Chipset 1/3” CMO
Camera Lens 2.8mm
Resolution 650 TVL
Camera Angle 120 degrees (D) / 90 degrees (H)
Camera Rating IP66 Outdoor Rated
IR LED 9 LED
Illumination 0 Lux – IR on
/N ration >45db
Electronic hutter 1/60 ~ 100,000
Auto Gain Control Auto
Back Light Compensation Auto
White Balance Auto
TV ystem NT C
Camera Power DC12V ~ 24V 125mA
Humidity <90%
Temperature Range –Operating -4F ~ 150F ( -20C ~ +65C)
Monitor
LCD creen ize 7” TFT LCD
Resolution 800 x 480
Channels 2 – RCA Video Input
Brightness / Contrast 500cd/m2 / 500:1
O D Control Contrast, harpness, Brightness, NT C
Viewing Mode Normal, Mirror, Flip
Monitor Power DC 12V ~ 24V 150mA
Cable
Environment Indoor
Pin 4 Pins (Video, Audio and Power)
Warning:
Install equipment only when vehicle is safely parked, leveled and power Off
View and access the monitor only when safe to do so
Review surrounding before operating / moving vehicle
Observe all electrical safety guideline and polarity to avoid injury
Please consult with Vehicle Manufacturer for warranty and settings prior to installation
Ventra is not responsible for any warranty pertaining to the vehicle
InstallationGuide
1. Determine the location and mounting position of the camera prior to installation
2. Test the viewing angle by powering both the camera and monitor before permanently securing the camera
3. Once location is determined, securely affix mounting bracket of the camera to the vehicle
4. Connect the EX4-XC camera to EX4-CBL 4 pin DIN cable. Ensure the cable is securely connected. (Refer to
installation diagram). EX4-CBL cable is not waterproof and should NOT be exposed to direct sunlight, rain or element. Cable should be
placed in conduit or outdoor rated sleeve
5. Connect the EX4-CBL cable to RVC-PIG DIN to RCA / Power cable
1. VC-PIG:
- 2 power pigtail wire ( ed = 12V Positive, Black = Ground) to a power source (i.e. tail light, reverse light or vehicle fuse)
- DC power plug to EX4-XC camera
- RCA connection to monitor via RCA cable
7. ecure RCA cable connection by applying heat shrink tube or electrical tape. Constant vehicle vibration may loosen connection
8. Connect the RCA cable into Input 1 of the VLCD-7 screen
V. 07 18

RVM -1XC433 Rear View Camera Kit
Ventra Technology Inc. Covina, CA. U A www.ventrainc.com [e-mail] Tel: [phone]
Installation layout
ecure cable connection by applying
heat shrink tube or electrical tape to
minimize movement from vehicle
vibration
EX4-CBL cable is not waterproof and should
not be exposed to direct sunlight, rain or
element. Cable should be placed in
weatherproof conduit or sleeve
Operation Guide:
1. VLCD-7 monitor supports dual video input. If only 1 camera is connected, that camera will be primary, regardless of which input it is
connected to
2. If connecting 2 cameras,
•Input 2 = Primary Camera
•Input 1 = econdary Camera
3. To switch camera view, Press for momentary view of the second camera, Or if the secondary camera was powered on / triggered
by a switch (i.e. turn signal). Monitor will auto revert back to the primary camera after approximately 5 seconds.
VLCD-7 Operation
1. Press ET key to Enter or Exit Menu
2. Press or to navigate menu. Press or to change setting
VLCD-7 equipped with U-shape bracket which may
be flipped for either dash or ceiling mount.
Removable sunshade may be used as needed