Veris Industries XPSD1 User manual

ZL0059-0B PAGE 1 ©2008 Veris Industries USA 800.354.8556 or 503.598.4564 / suppor[email protected] 8251-0024C 05082
6%2)3).$5342)%3
Surge Protection inStALLAtion guiDe
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
t 'PMMPXTBGFFMFDUSJDBMXPSLQSBDUJDFT 4FF/'1"&JOUIF64"PSBQQMJDBCMFMPDBMDPEFT
t 5IJTFRVJQNFOUNVTUPOMZCFJOTUBMMFEBOETFSWJDFECZRVBMJmFEFMFDUSJDBMQFSTPOOFM
t 3FBEVOEFSTUBOEBOEGPMMPXUIFJOTUSVDUJPOTCFGPSFJOTUBMMJOHUIJTQSPEVDU
t 5VSOPõBMMQPXFSTVQQMZJOHFRVJQNFOUCFGPSFXPSLJOHPOPSJOTJEFUIFFRVJQNFOU
t 6TFBQSPQFSMZSBUFEWPMUBHFTFOTJOHEFWJDFUPDPOmSNQPXFSJTPõ
t 3FQMBDFBMMEPPSTDPWFSTBOEQSPUFDUJWFEFWJDFTCFGPSFQPXFSJOHUIFFRVJQNFOU
Failure to follow these instructions will result in death or serious injury.
DANGER
XPSD1 XPSD1
/05*$&
t 5IJTQSPEVDUJTOPUJOUFOEFEGPSMJGFPSTBGFUZBQQMJDBUJPOT
t %POPUJOTUBMMUIJTQSPEVDUJOIB[BSEPVTPSDMBTTJmFEMPDBUJPOT
t 5IFJOTUBMMFSJTSFTQPOTJCMFGPSDPOGPSNBODFUPBMMBQQMJDBCMFDPEFT
t .PVOUUIJTQSPEVDUJOTJEFBTVJUBCMFmSFBOEFMFDUSJDBMFODMPTVSF
EQUIPMENT GROUNDING HAZARD
t %0/0564&0/6/(306/%&%4:45&.4
 5IJTEFWJDFNVTUCFDPOOFDUFEUPUIFFRVJQNFOUHSPVOEUPGVODUJPO4VSHFWPMUBHFT
 NVTUCFSFUVSOFEUPHSPVOEGPSEJTTJQBUJPO
Failure to follow these instructions will result in death or serious injury.
DANGER
POTENTIAL OF EQUIPMENT DAMAGE
t %0/0564&)*()70-5"(&5&45&26*1.&/5
 5IFVTFPGB.FHHFS
® PSPUIFSIJHIQPUFOUJBMUFTUHFBSXJMMEBNBHFUIJTTVSHF
 QSPUFDUJWFEFWJDF5VSOPõBMMQPXFSBOEJTPMBUFUIFTVSHFEFWJDFCFGPSFUFTUJOH
Failure to follow these instructions can result in equipment damage.
CAUTION
quick install
Installer's Specifications
Max. Surge Current 45kA/phase
Housing Type 1 (IP20)
Product Weight 0.56lb (255g)
Connection Method Parallel
Terminal Capacity #12-#4 AWG (3-25mm2)
Thermal Fusing Yes
Operating Temperature -30° to 70°C (-22° to 160°F)
Operating Frequency 50/60/400 Hz
Diagnostics Green Status LED
Poles 4
Service Voltage 208Y/120V
Dry Contacts Yes
Max. Surge Current per Phase 45kA
Rating 20A, Curve B
Supplementary Protection (Merlin-Gerin or Equivalent) MG24149 or MG24164
Mount the XPSD1 to the DIN rail.1.
Confirm the device is rated for your2.
system by comparing the L-N voltage
measurements to the Service Voltage
(Un). See the specifications on the product
housing.
Insure that the MGSP or equivalent are properly rated and matched to the wire3.
size.
Connect wires, keeping lead lengths as short as possible. Do not loop, bend, or coil4.
wires.
CLICK
SPD
D1
D2
D4
D3
N
L3L2L1 N
G
L3
L2
L1
MSGP
Surge Protective Device
Keep lead lengths short. For best practice, ensure that D1, D2, D3, and D4 are each <20 inches.

6%2)3).$5342)%3
inStALLAtion guiDe
XPSD1
ZL0059-0B PAGE 2 ©2008 Veris Industries USA 800.354.8556 or 503.598.4564 / suppor[email protected] 8251-0024C 05082
operation
troubleshooting
Problem Solution
LED off Fault. Check line voltage, breakers, and connections. If
OK, replace unit.
The XPSD1 surge protective device provides surge protection for electrical and
automation cabinets. It mounts onto 35 mm DIN rail near the incoming power source
to isolate the cabinet from the outside environment.
Note: this device must be installed with proper supplementary protection (MGSP or
equivalent; see specifications).
MGSP
L3
N
L2
L1
G
L1 L2 L3 N
Load Breakers
*
* max. 30A per NEC or as per local code
Wiring Diagram
NC
NO
Normally Closed
Common
Normally Open
3
3
2
1
2
1
remote monitoring option
The XPSD1 includes a three-pin socket and plug
to allow the customer to wire one set of normally
open (N.O.) and normally closed (N.C.) dry
contacts to a remote monitoring indicator. The
customer must provide power for the indicator
(0.3A @ 125VAC, 110VDC; 1.0A @ 30VDC). In the
event of an alarm, the N.O. contact closes, and
the N.C. contact opens.
Dimensions
2.6”
(65 mm)
3.4”
(86 mm)
3.7”
(92 mm)
1.8”
(45 mm)
3.5”
(89 mm)
Three phase, 4-wire 208Y/120VAC
Diagnostics
ON = OK
OFF = Fault