Vermeiren 708D User manual

VERMEIREN
708D
I N S T R U C T I O N M A N U A L
MODE D’EMPLOI
G E B R U I K S A A N W I J Z I N G
GEBRAUCHSANWEISUNG
I S T R U Z I O N I P E R L ' U S O
M A N U A L D E I N S T R U C C I O N E S

Instructions to the specialist dealer
This instruction manual is part and parcel of the product and must accompany every product sold.
Version: B, May 2011
All rights reserved, including translation.
No part of this manual may be reproduced in any form what so ever (print, photocopy, microfilm or any other process) without
written permission of the publisher, or processed, duplicated or distributed by using electronic systems.
© N.V. Vermeiren N.V. 2011
Instructions pour les distributeurs
Ce manuel d'instructions fait partie du produit et doit accompagner chaque produit vendu.
Version : B, Mai 2011
Tous droits réservés, y compris la traduction.
Aucune partie de ce manuel ne peut être reproduite, sous quelque forme que ce soit (imprimée, photocopie, microfilm ou tout
autre procédé) sans l'autorisation écrite du publicateur, ni traitée, dupliquée ou distribuée à l'aide de systèmes électroniques.
© N.V. Vermeiren N.V. 2011
Instructies voor de vakhandelaar
Deze handleiding is deel van het product en dient bij iedere product te worden geleverd.
Versie: B, mei 2011
Alle rechten, inclusief vertaling, voorbehouden.
Niets uit deze handleiding mag geheel of gedeeltelijk in enige vorm (druk, fotokopie, microfilm of ieder ander procedé) zonder
de schriftelijke toelating van de uitgever worden gereproduceerd of met behulp van elektronische systemen worden verwerkt,
gekopieerd of verspreid.
© N.V. Vermeiren N.V. 2011
Hinweise für den Fachhändler
Diese Gebrauchsanweisung ist Bestandteil des Produkts und ist bei jeder Produkts auszuhändigen.
Version: B, Mai 2011
Alle Rechte, auch an der Übersetzung, vorbehalten.
Kein Teil der Gebrauchsanweisung darf in irgendeiner Form (Druck, Fotokopie, Mikrofilm oder einem anderen Verfahren) ohne
schriftliche Genehmigung des Herausgebers reproduziert oder unter Verwendung elektronischer Systeme verarbeitet,
vervielfältigt oder verbreitet werden.
© N.V. Vermeiren N.V. 2011
Istruzioni per il rivenditore
Il presente Manuale di istruzioni è parte integrante del prodotto e deve essere fornito assieme alla prodotto.
Versione: B, Maggio 2011
Tutti i diritti riservati (anche sulla traduzione).
Il presente manuale non può essere riprodotto, neppure parzialmente, con alcun mezzo (stampa, fotocopia, microfilm o altro
procedimento) senza l’autorizzazione scritta della casa produttrice, né elaborato, duplicato o distribuito con l’ausilio di sistemi
elettronici.
© N.V. Vermeiren N.V. 2011
Instrucciones destinadas a los distribuidores especializados
El presente manual de instrucciones es parte integrante del producto y se debe adjuntar a todas las producto que se vendan.
Versión: B, mayo 2011
Todos los derechos reservados, incluidos los de la traducción.
Se prohíbe la reproducción total o parcial del presente manual de cualquier forma (impresión, fotocopia, microfilm o cualquier
otro procedimiento), así como la edición, copia o distribución empleando sistemas electrónicos, sin el permiso escrito del
editor.
© N.V. Vermeiren N.V. 2011

708D
2011-05
Page 1
Contents
Preface ......................................................................................................................................2
1Productdescription......................................................................................................3
1.1 Intended Use ................................................................................................................ 3
1.2 Technical specifications .............................................................................................. 4
1.3 Components ................................................................................................................. 5
1.4 Accessories .................................................................................................................. 5
1.5 Location identification plate........................................................................................ 5
1.6 Explanation of symbols ............................................................................................... 6
1.7 Safety rules .................................................................................................................. 6
2Use................................................................................................................................6
2.1 Carrying the wheelchair .............................................................................................. 7
2.2 Mounting the rear wheels ............................................................................................ 7
2.3 Unfolding the wheelchair ............................................................................................ 7
2.4 Mounting or removing of the footrests ....................................................................... 7
2.5 Operating the brakes.................................................................................................... 8
2.6 Mounting or removing of arm supports ...................................................................... 8
2.7 Transfer in and out the wheelchair .............................................................................. 9
2.8 Correct position in the wheelchair .............................................................................. 9
2.9 Riding the wheelchair.................................................................................................. 9
2.10 Moving on slopes ...................................................................................................... 10
2.11 Negotiating steps or kerbs ......................................................................................... 10
2.12 Fold up the wheelchair .............................................................................................. 11
2.13 Taking off the wheels ................................................................................................ 12
2.14 Transport in the car .................................................................................................... 12
2.15 Use of the wheelchair as seat in a motor vehicle ...................................................... 12
3Installation and adjustment.....................................................................................14
3.1 Tools .......................................................................................................................... 14
3.2 Manner of delivery .................................................................................................... 14
3.3 Anatomical seat (OPTIONAL) ................................................................................. 15
3.4 Anatomical back (OPTIONAL) ................................................................................ 15
3.5 Adjust the brakes ....................................................................................................... 15
3.6 Adjusting of the footrests .......................................................................................... 16
4Maintenance..............................................................................................................16
4.1 Regular Maintenance................................................................................................. 16
4.2 Shipping and storage ................................................................................................. 17
4.3 Care ........................................................................................................................... 17
4.4 Inspection .................................................................................................................. 18
4.5 Disinfection ............................................................................................................... 18
5Guarantee..................................................................................................................20
6Disposal......................................................................................................................20
7Declaration of conformity........................................................................................20
8Maintenance plan......................................................................................................21
9Disinfection book ......................................................................................................21

708D
2011-05
Page 2
Preface
First of all we want to thank you for putting your trust in us by selecting one of our
wheelchairs.
The Vermeiren wheelchairs are the result of many years of research and experience. During
the development, special attention was given to the ease of use and the serviceability of the
wheelchair.
The expected lifetime of your wheelchair is strongly influenced by the care and maintenance
of the wheelchair.
This manual will help you get acquainted with the operation of your wheelchair.
Following the user instructions and the maintenance instructions are an essential part of the
warranty.
This manual reflects the latest product developments. Vermeiren has the right to introduce
changes without the obligation to adapt or replace previously delivered models.
For any further questions, please consult your specialist dealer.

708D
2011-05
Page 3
1 Productdescription
1.1 Intended Use
The wheelchair is intended for people with walking difficulties or no walking abilities.
The wheelchair is designed to transport 1 person.
The wheelchair is suited for indoor and outdoor use.
The user can propel the wheelchair by himself or have the wheelchair pushed by an
attendant.
The different types of fittings and accessories, and the modular construction allow full use by
persons disabled by:
paralysis
loss of limbs (leg amputation)
limb defects or deformations
stiff or damaged joints
heart insuffiencies and poor blood circulation
balance disturbances
cachexia (decrease in muscle)
and also for aged persons.
When providing for individual requirements:
body size and weight (max. 120kg (264.6 lb.))
physical and psychological condition
residential circumstances
environment
should be taken into consideration.
Your wheelchair should only be used on surfaces where all four wheels are touching the
ground and where there is sufficient contact to propel the wheels equally.
You should practice for use on uneven surfaces (cobblestones, etc.), slopes, curves and to
get past obstacles (kerbs, etc.).
The wheelchair should not be used as a ladder, nor is it a transport for heavy or hot objects.
When used on mats, carpeted floors or loose floor coverings, the floor covering can get
damaged.
Use only Vermeiren approved accessories.
The manufacturer is not liable for damage caused by the lack of or improper service or as a
result of not following instructions from this manual.
Compliance with the user and maintenance instructions are an essential part of the
guarantee conditions.

708D
2011-05
Page 4
1.2 Technical specifications
Technical terms below are valid for the wheelchair in standard settings.
If other footrest / arm support or other accessories are used, the tabulated values will change.
Make
Vermeiren
Address
Vermeirenplein 1/15, B-2920 Kalmthout
Type
Manual wheelchair
Model
708D
Maximum occupant mass
120 kg (264.6 lb.)
Description
Dimensions
Effective seat width
390 mm
(15.35 in.)
420 mm
(16.54 in.)
440 mm
(17.32 in.)
460 mm
(18.11 in.)
480 mm
(18.90 in.)
500 mm
(19.69 in.)
Overall width (depends on the seat width)
560 mm
(22.04 in.)
590 mm
(23.23 in.)
610 mm
(24.02 in.)
630 mm
(24.80 in.)
650 mm
(25.59 in.)
670 mm
(26.38 in.)
Description
Dimensions Min.
Dimensions Max.
Overall length with legrest
1060 mm (40.94 in.)
Folded length without legrest
810 mm (31.89 in.)
Folded width
280 mm (11.02 in.)
Folded height
920 mm (36.22 in.)
Total mass
± 18 kg (39.68 lb.)
Mass of heaviest part
10,10 kg (22.05 lb.)
Masses of parts that can be dismantled or
removed
Foot supports: 1,90 kg (4.19 lb.); Arm supports: 1,85 kg (2.20 lb.);
Rear wheels: 4,15 kg (8.82 lb.)
Static stability downhill
15°
Static stability uphill
15°
Static stability sideways
15°
Obstacle climbing
60 mm (2.36 in.)
Seat plane angle
5°
Effective seat depth
430 mm (16.93 in.)
Seat surface height at front edge
500 mm (19.69 in.)
Backrest angle
5°
Backrest height
420 mm (16.54 in.)
Distance between footrest and seat
420 mm (16.54 in.)
500 mm (19.69 in.)
Angle between seat and footrest
9°
Distance between armrest and seat
220 mm (8.66 in.)
Front location of armrest structure
300 mm (11.81 in.)
Handrim diameter
535 mm (21.06 in.)
Horizontal location of axle (deflection)
-7 mm (-0.28 in.)
Minimum turning radius
1619 mm (63.74 in.)
Diameter Krypton PU Rear wheels
24"
Tyre pressure, rear (driving) wheels
Max. 3.5 bar
Diameter Krypton PU steering wheels
200 mm (8 in.)
Tyre pressure, steering wheels
Max. 2.5 bar
Storage and use temperature
+ 5 °C (+41 °F)
+ 41 °C (+106 °F)
Storage and use humidity
30%
70%
We reserve the right to introduce technical changes. Measurement tolerance ± 15 mm / 1,5 kg / ° (0.59 in. / 3,3 lb. / 1,5°)
Table 1: Technical specifications 708D

708D
2011-05
Page 5
The wheelchair complies to the requirements set up in:
ISO 7176-8: Requirements and test methods for static, impact and fatigue strengths.
EN 1021-1: Assessment of the ignitability of upholstered furniture - Ignition source
smouldering cigarette
EN 1021-2: Assessment of the ignitability of upholstered furniture - Ignition source match
flame equivalent
ISO 7176-19: Wheeled mobility devices for use as seats in motor vehicles.
1.3 Components
1.4 Accessories
The following accessories are available for the 708D:
Armrests (B02, B03, B05, B66)
Leg supports (B06, B07, B08, BZ7, BZ8, BZ9, BZ10, BK7, BL7, BA6, BK6)
Table (B12)
Crutch holder (B31)
Back (L14, L24, L44)
Anterior pelvic belt (B58) for mounting over the backrest tube
Anti-tipping device (B78) for mounting on the bottom back frame
Drum brakes for the attendant (B74) for mounting on the push handles
Transit wheelchair (T30)
Moving the axle back (AMP)
Quick release (B80)
Lowering seat height to 470 mm (S)
1.5 Location identification plate
1 = Taxi hooks
2 = Identification plate
3 = Name 708D
1 = Cross
2 = Handles
3 = Back
4 = Arm pads
5 = Arm supports
6 = Driving wheels (rear wheels)
7 = Hand rims
8 = Brakes
9 = Tip cap
10 = Steering wheels (Front wheels)
11 = Seat
12 = Footrests

708D
2011-05
Page 6
1.6 Explanation of symbols
Maximum mass
Indoor and outdoor use
Down slope
Up slope
CE conformity
1.7 Safety rules
L To prevent injury and/or damage to your wheelchair, make sure that no objects
and/or body parts are caught in the spokes of the driving wheels.
L The parking brakes should be applied before getting into and out of the wheelchair.
L When getting into and out of the wheelchair, do not stand on the footplates. These
should be folded up beforehand, or the leg supports should be swung completely
outwards out of the way.
L Investigate the effects of shifting the centre of gravity on the behavior of the wheelchair,
for example on up or down gradients, on laterally sloping ground, or when overcoming
obstacles. Obtain support from an attendant.
L If you want to pick up something (lying in front of, on the side, or to the rear of the
wheelchair), you should not lean too far out to avoid tipping over.
L When moving through doors, arches, etc. ensure that there is enough room at the sides
so that you do not get your hands or arms caught or crushed and that there is no
damage to the wheelchair.
L Only use your wheelchair according to regulations. For example, avoid uncontrolled
rolling against obstacles (steps, kerbs, doorframes, etc) or dropping down from ledges.
The manufacturer cannot assume liability for damage caused by overloading, collision
or other improper use.
L Stairs may only be negotiated when aided by another person. If furnishings like drive-on,
ramps or lifts are available, use them.
L When moving on the public highway, you are subject to the rules of the road.
L When driving your wheelchair, you should not be under the influence of alcohol or
medicine as in the case of driving other vehicles. This also applies to indoor driving.
L When travelling outdoors, adapt your driving to weather and traffic conditions.
L When transporting the wheelchair, never pick it up by grasping movable parts (armrests,
leg supports, etc.)
L To be better visible when driving in the dark, wear the brightest possible clothing or
clothes with reflectors, and check that the reflectors mounted on the sides and rear of
the wheelchair are clearly visible.
L Be careful when using possible causes of fire such as cigarettes since they may set the
seat and back covers alight.
L Never exceed the maximum load of 120 kg (264.6 lb.).
2 Use
This chapter describes the everyday use. These instructions are for the user and the
specialist dealer.
The wheelchair is delivered fully assembled by your specialist dealer. The instructions
intended for the specialist dealer on how to set up the wheelchair are given in § 3.

708D
2011-05
Page 7
2.1 Carrying the wheelchair
The best way to carry the wheelchair is to make use of the wheels and roll the wheelchair.
If this is not possible (e.g. when the rear wheels are taken off for transportation in a car),
firmly grasp the frame on the front and the grips. Do not use the foot or arm rests or the
wheels to grasp the wheelchair.
2.2 Mounting the rear wheels
1. Take the rear wheel and push on button .
2. Keep the button pushed in and mount the rear
wheels axle till it stops.
3. Release the button.
4. Check that the wheel is secured.
2.3 Unfolding the wheelchair
LCAUTION: Risk of clamping – Keep fingers away from moving parts of the
wheelchair.
1. Position yourself behind the wheelchair.
2. Use the hand-grips to open the wheelchair as much as possible.
3. Position yourself at the front of the wheelchair.
4. Push both seating tubes down till they are fixed in their position.
2.4 Mounting or removing of the footrests
LWARNING: Risk of injury – Check that the leg supports are securely locked in
place before use.
LCAUTION: Risk of clamping – Keep objects and people away from the leg
supports swing range.
The mounting of the footrests is done as follows:
1. Hold the footrest sideways at the outside of the
wheelchairs frame.
2. Mount the holes  of the footrest on the pins 
located on the frame.
3. Turn the footrest inwards till it clicks in position. If this
lock is a little stiff, press the handle gently back.
4. Turn the foot plate downwards.
5. Replace the calf strap in the hooks .
To take off the footrests:
1. Remove the calf strap by unhooking it on both sides.
2. Pull back the lever  near the footrest
attachment.
3. Turn the footrest to the outside of the wheelchair.
4. Lift the holes  of the footrest out of the pins
located on the frame .

708D
2011-05
Page 8
2.5 Operating the brakes
LWARNING: The brakes are not used to slow down the wheelchair during
movements – Use the brake only to prevent the wheelchair from unintended
movements.
LWARNING: Good operation of the brakes is influenced by wear and
contamination of the tires (water, oil, mud, …) – Check the condition of the tires
before each use.
LWARNING: The brakes are adjustable and can wear – Check the operation of the
brakes before each use.
To apply the brakes:
1. Push the brake handles  forward till you feel a
distinctive click.
LCAUTION: Risk of unintended movement –
Make sure the wheelchair is on a flat
horizontal surface before releasing the
brakes. Never release both brakes
simultaneously.
To release the brakes:
1. Release one brake by pulling the handle 
backwards.
2. Hold the hand-rim of the release wheel with
your hand.
3. Release the second brake by pulling the handle
backwards.
2.6 Mounting or removing of arm supports
LCAUTION: Risk of clamping – Keep fingers, buckles and clothes away from the
bottom side of the arm support.
The arm supports of the wheelchair can be mounted by following instructions.
1. Mount the rear tube of the arm rest in tube hood . (Fig A)
2. Make sure the arm support is mounted very well.
3. Fold the arm rest forward.
4. Pull the lever on tube hood upwards. (Fig B)
5. Click the front tube of the arm rest  in tube hood . (Fig B)
A
B

708D
2011-05
Page 9
To open and remove the arm rest:
1. Pull lever  and pull the front of the arm rest  upwards. (Fig C)
2. Fold the arm rest backwards.
3. To remove the arm rest, pull the rear of the arm support from tube hood . (Fig D)
2.7 Transfer in and out the wheelchair
LCAUTION: In case you can not perform the transfer in a safe manner, ask
someone to assist you.
LCAUTION: Risk of tipping over of the wheelchair – Do not stand on the foot
plates.
1. Position the wheelchair as close as possible to
the chair, couch or bed to/from you wish to
transfer.
2. Check both brakes from the wheelchair are in
the on position.
3. Fold the foot plates upwards to prevent
standing on them.
4. If the transfer is on the side of the wheelchair,
fold the arm support on that side upwards.
(see § 2.6)
5. Transfer to/from the wheelchair.
2.8 Correct position in the wheelchair
Some recommendations for a comfortable use of the wheelchair:
Position your backside as close as possible to the back rest.
Make sure your upper legs are horizontal – If needed adjust the length of the foot
rests. (see § 3.6.1)
2.9 Riding the wheelchair
LWARNING: Risk of clamping – Prevent your fingers from being caught by the
wheels spokes.
LWARNING: Risk of clamping – Be careful passing through restricted passages
(e.g. doors).
LWARNING: Risk of burns – Be careful when driving in hot or cold environments
(sunshine, extreme cold, saunas, etc.) for a sufficient amount of time and when
touching - Surfaces can assume the environment temperatures.
C
D

708D
2011-05
Page 10
1. Release the brakes.
2. Take both hand rims at their highest position.
3. Lean forward and push the hand rims forward until straight arms.
4. Swing your arms loosely back to the hand rims topside and repeat the movement.
2.10 Moving on slopes
LWARNING: Control your speed – Moving on slopes as slow as possible.
LWARNING: Consider the capacities of your attendant – If your attendant does not
have enough force to control the wheelchair, put on the brakes.
LWARNING: Risk of tipping over – Lean forward to move your centre of gravity
forward. To improve a better stability.
1. If available on the wheelchair, wear the safety belt.
2. Do not attempt moving on too high slopes. The maximum
slope angles (upwards and downwards) are mentioned in
table 1.
3. Ask an attendant to help you moving on the slope.
4. Lean forward to move your centre of gravity forward.
2.11 Negotiating steps or kerbs
2.11.1 Getting down steps or kerbs
Riding down low kerbs can be done moving forwards. Make sure that the foot rests do not
touch the ground.
A practiced user can negotiate small steps or kerbs by himself:
L WARNING: Risk of tipping over – If you do not have
enough experience with your wheelchair, ask
assistance of an attendant.
1. Bring balance on the rear wheels to reduce the pressure on
the front wheels.
2. Negotiate the kerbs.
Higher kerbs can be taken forward with an attendant:
1. Ask the attendant to tip the wheelchair slightly backwards.
2. Get past the kerbs while moving on the rear wheels.
3. Put the wheelchair back on the four wheels.
An experienced user can negotiate higher kerbs by himself. This is
best done backwards.
1. Turn the wheelchair to have the rear wheels facing the
kerb.
2. Lean forward to move your centre of gravity forward.
3. Move the wheelchair close to the kerbs.
4. Use the hand rim to roll-off wheelchair from the kerb in a
controlled manner.

708D
2011-05
Page 11
2.11.2 Moving up steps or kerbs
Moving up steps or kerbs with attendant as follows:
1. Prevent the foot rests from touching the kerb.
2. Ask the attendant to tip the wheelchair backwards, just
enough to move the front wheels over the kerb.
3. Lean backwards to move your centre of gravity above the rear
wheel.
4. Place the front wheels on the kerb.
5. Roll rear wheels of the wheelchair over the kerb.
Higher kerbs are negotiated backwards:
1. Turn the wheelchair to have the rear wheels facing the kerb.
2. Lean backwards and move your centre of gravity above the rear wheels.
3. Ask the attendant to pull the wheelchair on the kerb.
4. Take back the normal position in the wheelchair.
An experienced user can negotiate kerbs by himself:
LWARNING: Risk of tipping over – If you have not enough experience to control
the wheelchair, get help from an attendant.
1. Drive until the kerbs.
2. Ensure that the footrest do not touch the kerbs.
3. Lean backwards so you are balancing on the rear wheels.
4. Role the frontwheels balancing over the kerbs.
5. Bend forward for more stability.
6. Role the rear wheels over the kerbs.
2.11.3 Taking of stairs
Taking of stairs while you staying in the wheelchair shall be according following rules:
LWARNING: Risk of tipping over – Taking of stairs shall always with 2 attendants.
1. Remove the footrests.
2. One attendant tip the wheelchair slightly backwards.
3. The second attendant take the front of the frame.
4. Stay calm, avoid sudden movements and keep your arms inside the wheelchair.
5. Take the steps on the rear wheels of the wheelchair.
6. Mounting the footrests back after taking the stair.
2.12 Fold up the wheelchair
L CAUTION: Chance of pinching – Do not place fingers between the components
of the wheelchair.
1. Fold or remove the footplates (see § 2.4).
2. Take the seat on the front side and backside and pull it up.

708D
2011-05
Page 12
2.13 Taking off the wheels
To facilitate the transport off the wheelchair the rear wheels can be taken off:
1. Make sure the brakes standing in the off
position.
2. Take the wheelchair to the side frame where
you want to remove the wheel.
3. Press the button  in the center of the wheel
hub.
4. Pull the wheel away from the frame.
2.14 Transport in the car
LWARNING: Risk of injury – See that the wheelchair is attached properly. So you
can avoid injury from the passengers during collision or sudden braking.
LWARNING: Risk of injury – Use for attaching the wheelchair and passenger
NEVER the same seatbelt.
1. Remove footrests and accessories.
2. Store footrests and accessories safely.
3. If possible, fold the wheelchair and remove the wheels.
4. Place the wheelchair in the luggage place.
5. If the wheelchair and the passenger compartment is NOT separated, attach the
frame of the wheelchair securely to the vehicle. You can use the available safety
belts in the vehicle.
2.15 Use of the wheelchair as seat in a motor vehicle
LWARNING: The wheelchair has passed the crash of ISO 7176-19: 2008 and, as
such, has been designed and tested for use only as forward-facing seat in a
motor vehicle.
LWARNING: The wheelchair's pelvic belt alone is not suited as an occupant
restraint belt.
The wheelchair is tested using the four-point strap-tie system and a 3-point occupant-
restraint system.
Whenever feasable, use the seat of the vehicle and store the wheelchair in the cargo area.
Steps to secure the wheelchair in a motor vehicle:
1. Check that the vehicle is equipped with a suitable wheelchair tie down and occupant-
restraint system, conform ISO 10542.
2. Check that the components of the wheelchair tie down and occupant restraint system
are not frayed, contaminated, damaged or broken.
3. If equipped with an adjustable seat and/or back tilt, make sure that the wheelchair
user is sitting as upright as possible. If the user's condition prevents this, a risk
assessment should be done to evaluate the user's safety during transit.
4. Remove all mounted accessories such as trays and respiratory equipment, and
secure them in a safe place.
5. Position the wheelchair facing forward in the travelling direction, centrally between
the tie-down rails mounted in the floor of the vehicle.
6. Make sure that the indicated zones around the wheelchair user are clear from rigid
vehicle parts.

708D
2011-05
Page 13
7. Mount the front securement straps according to the instructions of the strap-system
manufacturer at the indicated place. (figure 3)
This place is marked on the wheelchair with a symbol. (figure 4)
8. Roll back the wheelchair until the front straps are tight.
9. Apply the wheelchair brake.
10. Mount the back securement straps according to the instructions of the strap-system
manufacturer at the indicated place. (figure 3)
11. This place is marked on the wheelchair with a symbol. (figure 4)
figure 3
Steps to secure the wheelchair user:
1. Remove both arm rests.
2. If present, attach the wheelchair's pelvic belt.
3. Attach the occupant restraint belts according to the instructions of the strap-system
manufacturer.
4. Wear the pelvic belt low across the front of the pelvis, so that the angle of the pelvic
belt is within the preferred zone of 30° to 75° to the horizontal, similar to that shown
below.

708D
2011-05
Page 14
5. A steeper (greater) angle within the preferred zone is desirable.
6. Adjust the belt tightly according to the instructions of the strap-system manufacturer,
consistent with the user's comfort.
7. Ensure that the restraint belt connects in a straight line to the anchor point in the
vehicle and that no bends in the belt are visible, for instance at the axle of the rear
wheel.
8. Install the arm rests, if desired. make sure that belts are not twisted or held away
from the body by wheelchair components such as arm rests or wheels.
3 Installation and adjustment
The instructions in this chapter are for the specialist dealer.
The Vermeiren wheelchairs 708D has been designed entirely for your comfort.
To find a service facility or specialist dealer near you, contact the nearest Vermeiren facility.
A list of Vermeiren facilities can be found on the last page.
LWARNING: Risk of unsafe settings - Use only the settings described in this
manual.
LWARNING: Variation of allowed adjustments can still change the stability of your
wheelchair (tilt back or sideways).
3.1 Tools
To set up the wheelchair the following tools are needed.
Wrench set n° 10 to n° 19
Allen key set n° 4 to n° 5
Screwdriver Phillips head
3.2 Manner of delivery
The Vermeiren 708D shall be delivered with:
1 frame with arm supports, rear and front wheels (seat height of 500 mm - 19.69 in.,
seat angle of 5°)
1 pair footrests
Back and seat cushions
Tools
Manual
Accessories (optional)
Pump (with pneumatic tyres only)

708D
2011-05
Page 15
Before use check if everything is included and that no products are damaged (example by
transport, ...).
3.3 Anatomical seat (OPTIONAL)
LWARNING: Risk of injury – Check that the seat is secure before use.
LWARNING: Risk of injury – Avoid getting your fingers caught during the
assembly process.
If you have opted for an anatomical padded seat, place it on
the tubular cross-hinge so that the seat's supports engage
equally with the cross-hinge. In the wooden base you will find
slots that are placed in the hinge's cross-pieces. To fold up the
wheelchair, remove the seat by pulling it upwards.
3.4 Anatomical back (OPTIONAL)
LWARNING: Risk of injury – Check that the backrest is secure before use.
LWARNING: Risk of injury – Avoid getting your fingers caught during the
assembly process.
To use the anatomical backrest, proceed as follows:
1. Unscrew the flexible backrest.
2. Loosely screw on the brackets for the backrest.
3. Insert the backrest into the brackets from above.
4. Tighten the screws holding the brackets for the
backrest.
5. Insert and tighten the safety screws for the
backrest.
6. Add the armrests.
3.5 Adjust the brakes
LWARNING: Risk of injury – Brakes may only be adjusted by your specialist
dealer.
Adjust the brakes according following rules:
1. Install the wheels according § 2.2.
2. Disconnect the brakes by pulling lever 
backwards.

708D
2011-05
Page 16
3. Loosen the selflocking nut  so the brake
mechanism can slide over the frame tube .
4. Pull the brake mechanism over the tube  to the desired
position. (the adjustments range shall be possible
between the groove on the brake montage plate)
5. Retighten the selflocking nut .
6. Check working of the brakes.
7. If necessary repeat the above steps until the brakes are
adjusted well.
3.6 Adjusting of the footrests
3.6.1 Length of the footrests
L CAUTION: Risk of damage – Avoid that the footrests make any contact with the
ground. Keep a minimum distance from 60 mm (2.36 in.) above the ground.
Adjust the length of the footrests as follow:
1. Remove the Allen screw  on the lower end
of the upper part of the leg support.
2. Adjust the length of the footrest to a
comfortable length by moving the
hexagonal inner tube out or in.
3. Tighten the Allen screw properly.
The minimum length is when the
footrest tube changes from
hexagonal in round.
The maximum length is until the
mark in the tube. (These mark is a
straight line)
4 Maintenance
Lifetime of the wheelchair is influenced by its use, storage, regular maintenance, servicing
and cleaning.
4.1 Regular Maintenance
The maintenance activities to ensure a good condition for your Vermeiren wheelchair are
described below:
Before every ride
 Check the tyres and make them clean. If necessary change the tire.
 Check screw fastenings are secured.
 Check the brakes and adjusted if necessary.
 Check the wheelchair (cleanliness, cracks, damage on structural parts ... .)
and make it clean. If necessary change the coating.

708D
2011-05
Page 17
Every 8 weeks: inspected and lubricating or adjusting from
 Arm supports
 Footrests
 Brake lever
 Wheel axles
Every 6 months or for every new user
 General review
 Disinfection
 Frontwheels, possibly clean bearings
For your convenience, on the back of this manual is a maintenance plan.
Repairing and assembling of spare parts for your wheelchair may only be performed by the
specialist dealer.
Only authorized Vermeiren spare parts may be installed.
4.2 Shipping and storage
The shipping and storage of the wheelchair shall be according following instructions:
Store in a dry place (between +5 °C and +41 °C).
The relative humidity of the air should be between 30% and 70%.
Provide sufficient covering or packaging to protect the wheelchair from rust and
foreign bodies. (e.g. salt water, sea air, sand, dust).
Store all removed parts together in one place (or mark them if necessary) to avoid
mixing up with other products when re-assembling.
Components must be stored without being subjected to strains (Do not put too heavy
parts on the wheelchair, not clamping between something, ...).
4.3 Care
4.3.1 Seat and back cushion
The cleaning of the seat and back cushion shall be according:
 Clean seat and back with a cloth moistened with hot water. Be aware that you do not
soak the seat and back cushion.
 Use a mild commercial detergent for removing stubborn dirt.
 Stains can be removed by using a sponge or a soft brush.
 Do not use strong cleaning liquids like solvents, nor use hard brushes.
 Never clean with steam and/or pressure washers.
4.3.2 Plastic parts
Clean plastic parts of your wheelchair with commercial plastic cleaners. Only use a soft
brush or soft sponge. Examples of plastic parts are the armrests, handles, tyres and ... .
4.3.3 Coating
The high quality of the surface layer guarantees optimal protection against corrosion. If the
outer coat is damaged by scratching or in some other way, get your specialist dealer to
repair the affected surface.
When cleaning, only use warm water and normal household detergents and soft brushes
and cloths. Ensure that no wetness gets into the tubes.
Initially the zinc parts only require rubbing with a dry cloth. Stubborn dirt can best be
removed by using a suitable commercial zinc polish.

708D
2011-05
Page 18
4.4 Inspection
In principle we recommend one inspection every year, and a minimum of one before usage
is resumed. All of the following checks must be performed and documented by authorized
persons:
Check the frame parts and the hinged tubes for plastic deformation, cracks and
impaired functioning.
Visually check for damage to the paintwork (danger of corrosion)
Check the operation of the wheels (free running, level rolling, axle play, tyres, profile,
condition of the rims, air pressure in the case of air tyres, floating axles, etc.)
Check the solidity and seating of all screws.
Verify the amount of grease on the metal joints of movable parts
The condition and security of the guides and axles of the steering wheels
Visually check all plastic parts for cracks and brittle spots
Check the functioning of the armrests and leg supports (locking, load, deformation,
wear caused by loads).
Check the operation of other detachable parts (example: anti-tipping device, personal
safety belt, fitting back/seat, etc.)
Completeness of the delivery condition, instruction manual available?
The service must only be signed off in the maintenance plan if a minimum of all the above-
mentioned aspects have been checked.
4.5 Disinfection
LWARNING: Dangerous Products - The use of disinfectants is restricted to
authorized personnel.
LWARNING: Dangerous Products, change on irritate your skin - You should wear
suitable protective clothing because the disinfectants could irritate your skin. For
this purpose you should also take note of the product information of the solutions
concerned.
All parts of the wheelchair can be treated by scrubbing with a disinfectant.
All steps taken to disinfect rehabilitation equipment, their components or other accessory
parts are to be recorded in a disinfection report containing a minimum of the following
information (with product documentation appended):
Date of the
disinfection
Reason
Specification
Substance and
concentration
Signature
Table 2: Example of a disinfection book
Abbreviations used in column 2 (reason):
V = Suspected infection IF = Infection case W = Repetition I = Inspection
For a blank sheet of a disinfection book see § 9.
The recommended disinfectants for scrubbing (based on the list provided by the Robert
Koch Institute, RKI) are standing in the table below. The current state of the disinfectants
included in the RKI list can be obtained from the Robert Koch Institute (RKI) (homepage:
www.rki.de).