Vermeiren Alesia User manual

VERMEIREN
Alesia
INSTRUCTION MANUAL
MODE D’EMPLOI
GEBRUIKSAANWIJZING
GEBRAUCHSANWEISUNG
ISTRUZIONI PER L'USO
MANUAL DE INSTRUCCIONES
INSTRUKCJA OBSŁUGI

E
CONTENTS
Section Page
Contents.............................................................................................................................................1
Preface...............................................................................................................................................2
Applicability ........................................................................................................................................2
General notes ....................................................................................................................................2
Alesia components.............................................................................................................................3
Technical details ................................................................................................................................3
Assembly ...........................................................................................................................................4
•Seat .............................................................................................................................................4
•Back.............................................................................................................................................4
•Headrest ......................................................................................................................................5
Seat angle..........................................................................................................................................5
Adjusting the back..............................................................................................................................6
Armrests.............................................................................................................................................7
Footplate ............................................................................................................................................7
Brakes (central locking) .....................................................................................................................8
Directional wheel................................................................................................................................8
Accessories........................................................................................................................................9
•Document holder (B79) ...............................................................................................................9
•Pads (L04) ...................................................................................................................................9
•Serum holder (B52) .....................................................................................................................10
•Multi-purpose holder....................................................................................................................10
•Adjustable legrest ........................................................................................................................11
•Treatment table (B12)..................................................................................................................11
•Urine bag holder ..........................................................................................................................11
Transport............................................................................................................................................12
Using ramps .......................................................................................................................................12
For your safety ...................................................................................................................................12
Making regular checks .......................................................................................................................12
Inspection...........................................................................................................................................13
Care ...................................................................................................................................................13
Disinfection ........................................................................................................................................14
Storage ..............................................................................................................................................15
Disposal .............................................................................................................................................15
Guarantee ..........................................................................................................................................16
Conformity..........................................................................................................................................16
Dealer information:
This instruction manual is part and parcel of the product and it should accompany each product delivered.
Last updated: 06/2009
All rights reserved, including translation.
No part of this manual may be reproduced in any form whatsoever (print, photocopy, microfilm or any other
process) without written permission of the publisher, or processed, duplicated, or distributed by using electronic
systems.
!N.V. Vermeiren N.V., 2009

E
ALESIA
06/2009
2
PREFACE
First of all we wish to thank you for the trust you placed in us by selecting one of our products.
Vermeiren products are the result of reseach and experience over many years. In development,
simplicity of operation and servicing was particularly emphasised.
The product's service life depends very much on the care with which it is used and handled. This user
manual aims to help familiarise you with using your recliner. You will also find advice as to how to
keep your product in good working order and ensure that it will have a long service life.
This user manual relates to the latest version of the product. However, Vermeiren reserves the right to
introduce changes without any obligation to adapt or replace previously delivered models.
Remember that, by following these instructions, you will help keep your recliner in the best possible
condition and fully-functional even after many years' use.
If you have any further questions, kindly consult the dealer.
APPLICABILITY
In the ALESIA mobile chair you have acquired a product that has been developed with an enormous
emphasis on comfort. The ALESIA mobile chair should only be used indoors. It may not be used
outdoors. Persons who are to be moved with the chair must at least have sufficient bodily control and
should have no balance disorders that might affect sideways stability, otherwise precautions should be
taken to secure the patient. It should not be used as a ladder, or as a resting place for hot, cold or
heavy objects or to move items. Read this user manual thoroughly to familiarise yourself with your
product.
The equipment enables use in cases where movement is restricted due to:
!Paralysis/weakness (while retaining control of the torso)
!Joint injuries
!Illnesses such as heart and circulation failure
The indication should take into account factors such as the following:
!Size and weight (max. load 140 kg)
!Physical and mental condition
!Living environment
A guarantee can only be given when the product is used under the circumstances specified
above and for the intended purposes.
GENERAL NOTES
The frame of the ALESIA chair is made of high-quality, powder-coated steel. The use of synthetic
leather covers enables easy care and cleaning. The seating systems were designed based on
ergonomic principles for your comfort.
The angles of the seating system, the back and the legrest can be adjusted using a pneumatic
cylinder.

E
ALESIA
06/2009
3
ALESIA COMPONENTS
TECHNICAL DETAILS
(Given for the fully-assembled, standard version). Please note that adding accessories will alter the technical details
accordingly.
ALESIA
Total length in seated position
80 cm
Total length in lying position
133 cm
Total width
70 cm
Seat width
54 cm
Height of backrest
80 cm
Total height with headrest (optional)
133 cm
Height of seat
53 cm
Seat depth
48 cm
Height of armrests
0 cm - 27 cm
Total weight *
From 33 kg
Max. load
140 kg
Angle of back (150N pneumatic spring)
Approx. 30°
Angle of seat (400N pneumatic spring)
Approx. 12°
Legrest length
33 cm
Legrest adjustment (optional)
Approx. 85° (stop notch)
Front steering castors
125 x 32
Rear steering castors (central locking)
125 x 32 (with brake)
We reserve the right to introduce technical changes. Differences of +/- 1.5 cm/kg, 1.5° are possible.
* Excluding headrest and accessories.
2
5
1
3
6
7
4
8
9
ALESIA
1 = Back
2 = Adjust angle of back
3 = Headrest (optional)
4 = Armrest
5 = Lever to adjust armrest
6 = Seat/legrest
7 = Footrest
8 = Foot lever brake (central lock),
foot lever for direction wheel
9 = Torso pad (optional)
10 = Foot lever for angle of seat (not shown)
2

E
ALESIA
06/2009
4
ASSEMBLY
•SEAT
The seat is clipped to the basic frame with clamps.
Lay the seat (1) at a slight angle to the curved clamp (2) in such a way that the clamp catches
beneath the rear cross tube on the basic frame (3).
Press the front of the seat (1) downwards so that the U-clamp (4) engageds on the front cross
tube of the basic frame (5).
The Velcro fastener (6) is used to attach the lower leg padding to the braces on the frame of
the legrest (7).
If you wish to remove the seat, follow the reverse procedure.
LEnsure that no objects or body parts get caught between the seat and the frame!
•BACK
When assembling the back, the pneumatic spring is connected to the rear frame with a safety pin (1).
Align the rear frame so that the retainer on the lower part of the back (2) and the mounting lug
of the pneumatic spring (3) are above one another.
B
A
A
2
3
1
1
4
A
B
2
1 = Seat
2 = Curved clamp
3 = Rear cross tube
4 = U-clamp
5 = Front cross tube
6 = Velcro fastener
7 = Legrest frame
3
5
1
A
2
4
B
6
7
C
B

E
ALESIA
06/2009
5
Guide the safety pin (1) through the rear retainer and the pneumatic spring. Then tighten the
safety pin (1) by guiding the tension spring (4) over the pin until the pin juts out above the end
of the locking pin.
•HEADREST (OPTIONAL)
The headrest is inserted into the retainer of the back section (A) and the pillow height can be adjusted.
The pillow can be removed or attached using the pushbutton on the lower end of the sliding plate on
the pillow.
SEAT ANGLE
An attendant can use the pneumatic spring to angle the seat unit, gradually, up to 12°, into the most
comfortable position, and to angle it forwards up to 3° to assist the patient to get in and out of the
chair.
With your foot, gently press downwards the release lever (highlighted in blue) on the right rear wheel
for the seat angle and adjust the seat unit to the position you want, by clutching the handle and
pushing the seat down or pulling it up. To fix it in the position you want, take your foot off the release
lever.
LEnsure that the rear wheel is not underneath the blue release lever, blocking it.
LTake care, when adjusting the seat angle, that the wheelchair does not start moving if the
brake is not holding it in place.
If you wish to move a patient, you should always select a gentle seat angle or the footplate (if
in use) will drag along the ground while doing so.
B
A

E
ALESIA
06/2009
6
ADJUSTING THE BACK
The patient or attendant can incline the back section backwards by up to 30°.
USE BY AN ATTENDANT
Pull the release clip beneath the handle towards the handle. While keeping the release lever
held, the back can be moved to the position you want by gripping the handle. To fix the back in
the position you want, let go of the release clamp beneath the handle.
LTake care, when adjusting the back, that the wheelchair does not start moving if the brake is
not holding it in place.
LThe pneumatic spring is designed to take the patient's weight. Without a weight and if the
release lever is not pressed, the back will always shoot back to the furthest forward position.
USE BY THE PATIENT
Pull the release lever, on the left or right next to the armrest retainer, gently upwards. While
keeping the release lever held, the back can be moved to the position you want by - while you
are seated - gently pressing your weight backwards against the back section or by slightly
bending your back forwards you will move the back of the chair forwards. To fix the back in the
position you want, let go of the release lever beneath the handle.
LTake care, when adjusting the back, that the wheelchair does not start moving if the brake is
not holding it in place.
LThe pneumatic spring is designed to take the patient's weight. Without a weight and if the
release lever is not pressed, the back will always shoot back to the furthest forward position.
A
B
A
B
B
A

E
ALESIA
06/2009
7
ARMRESTS
You can adjust the height of the armrests and lower them to the height of the seat in order to move the
patient sideways.
•Pull the armrest's release lever (1) upwards (towards the arm pad) and keep it held.
•Move the armrest to the height you want (2) and let go of the release lever (1) so that the armrest
can engage.
•To move the patient sideways, pull the release lever (1) and push the armrests down to the height
of the seat(3).
LThe armrest is not locked at seat height.
LWhen moving adjustable parts, ensure that no body parts or objects come within the range of
the adjustment and get caught!
FOOTPLATE
The footplate can be pulled out from beneath the chair to be used or pushed back beneath the chair
when not being used. When the footplate is pulled out, a weight should be kept on it.
Grip the front end of the footplate and
pull it out till it locks or, similarly, push
it back beneath the chair.
An attendant can push the footplate
forwards using the rear handle, or pull
it by the handle back beneath the
chair.
LThe footplate does not fold up - when
not in use it should be pushed/pulled
beneath the chair.
When the patient is getting in or out of the chair, the footplate must be pulled out and they should step
on it. The suspension mechanism allows the footplate to drop down so that it is entirely flat on the
ground.
LThe brake should always be applied before a patient gets in and out.
3
1
2
A
B
A
B

E
ALESIA
06/2009
8
LWhen the footplate is used to move a patient, the seat should be angled backwards, as only
then will the suspension mechanism raise the footplate slightly.
BRAKES (CENTRAL LOCKING)
To stabilise the chair, the two rear castors are fitted with a centrally locking brake.
Engaging the parking brake
Push downwards with your foot on the release lever on either
the right or left rear castor (labelled red) until the brake audibly
engages. The rear castors are now locked and will not roll or
turn.
Releasing the parking brake
Push upwards with the toes of your foot against the release
lever on either the right or left rear castor (labelled red) and
the rear castor brake will disengage.
DIRECTIONAL WHEEL
To stabilise the chair's movement characteristics while it is being pushed, the rear wheels can be
locked in such a way that the two rear castors move in a parallel track. This means that only the front
castors can be used to steer, which enables the chair to be pushed more easily.
Applying the directional wheel
With the toes of your foot, press downwards on the release
lever on either the left or right rear castor (labelled green).
Now move the chair till both castors are in parallel with the
frame and audibly lock.
Applying the directional wheel
To release the directional wheel function, with the toes of your
foot, press downwards on the release lever on either the left
or right rear castor (labelled red).
B
A
A
B

E
ALESIA
06/2009
9
ACCESSORIES
•DOCUMENT HOLDER (B79)
A holder can be clipped to the back of the chair to store
documents while the patient is being moved. There are two
screwholders in the rear frame to attach this. Mount the rail
using the two screws supplied so that the open rail ends are
outwards. The holder is hung onto the rail ends.
LThe document holder is only designed to hold a
maximum of 4 kg.
•PADS (L04)
The side pads can be folded away, and you can adjust their height, width and length. The pad
retainers can be mounted behind the back section. There are two screw joints in the rear frame to
attach the retainer bar.
MOUNTING
Insert the pad into the pad retainer behind the
back section in such a way that the head of the
adjustable screw (A) fits into the slot in the pad
retainer.
FOLDING AWAY
Raise the pad until the head of the adjustable
screw (A) comes out of the slot in the pad
retainer. Turn the pad outwards or inwards. In so
doing, the head of the adjustable screw (A) can
be guided to the edge of the pad retainer.
lAvoid twisting the tube.
ADJUSTING THE HEIGHT
The sideways height of the pads is fixed by
changing the position of the adjusting screw (A)
on the vertical tube of the side pad.
ADJUSTING THE WIDTH
You set the width by loosening the screw (B). The
sprocket so released can be put into the position
you want.
ADJUSTING THE LENGTH
The length of the side pads is set by loosening the
screw (C) on the side pad's horizontal tube (3
positions). The screw is then re-tightened.
The pad automatically adjusts to your position on
the body side via axle (D).
LEnsure that, after the adjustment, only padded parts are in contact with the body, or pressure
points can be created.
B
A
C
D
A

E
ALESIA
06/2009
10
LBefore use, please check that all the screws are tight.
lOnly have assembly and adjustments done by authorised persons.
LThe manufacturer accepts no liability for damage caused by improper pad adjustments.
•SERUM HOLDER (B52)
A serum holder can be attached for drips. On the rear
strut on the left-hand side, the bracket can be screwed
into the pre-drilled holds (A). The adjusting screw (B)
can be used to alter the length and angle of the strut.
lEnsure that all the screws are tight before
use.
lBefore using the serum holder, ensure that it
will not affect giving the drip properly.
lIf using the serum holder while moving the
patient, ensure that all the connecting tubes
have no kinks and are safely positioned.
lTake care as the serum holder may project
beyond the chair and bang into things!
lWhen moving a patient, go more slowly,
especially around bends, in order to avoid the
serum holder swinging.
•MULTI-PURPOSE HOLDER
The multi-purpose holder on the lower part of the frame can be used to hold e.g. a bottle holder B83
(e.g. for an oxygen cylinder) or the headrest when not in use.
lIf using the bottle holder while moving the patient, ensure that all the connecting tubes have
no kinks and are safely positioned.
lWhen moving a patient, go more slowly, especially around bends.
B
B
A
or
Oxygen cylinder holder B83

E
ALESIA
06/2009
11
•ADJUSTABLE LEGREST
There is an option of selecting a legrest that enables the leg position to be raised and set to different
angles.
Grip the left- or right-hand handle on the side
of the legrest (A) and pull it to the position you
want. To lower the legrest back again, pull the
legrest to its highest position (horizontal) and
the stop notch will release the legrest. It can
now be fully lowered once more.
•TREATMENT TABLE (B12)
A bracket (beneath the armpad) enables a wooden therapy table to be attached which can be
adjusted in terms of depth, removed and folded to the side.
•URINE BAG HOLDER
A bracket can be attached to the screw joints
on the front of the seat frame (A) on the left
and/or right of the side frame which will
enable a urine bag to be hung on two hooks.
lIf using the urine bag while moving
the patient, ensure that there are no
kinks or catches in any of the
connecting tubes and the bag.
lWhen moving a patient, go more
slowly, especially around bends, in
order to avoid the urine bag/s
swinging.
A
A

E
ALESIA
06/2009
12
TRANSPORTING
In order to carry the chair, the snap-bolt on the pneumatic spring attachment on the lower end of the
back section can be removed and the back can be folded forwards. If necessary, remove the headrest
(if there is one), push the footrest beneath the seat, and lower the legrest (if there is one) as far as it
will go. Remove any accessory that is attached if it affects the chair's overall dimensions.
LAt least two persons should always be involved in carrying it up or down staircases or steps. It
should not be carried with the patient in it.
lOnly lift the chair by fixed parts at the side of the frame. Do not lift it by the armrests or the
seat!
LWhen being carried, no persons or objects should be below the chair, to prevent personal
injury or damage to the product.
lIf being carried in a motor vehicle, the recliner should not be used as a seat.
lIn a motor vehicle, the chair should be made secure using appropriate safety belts attached to
the side of the frame.
USING RAMPS
If you are considering ramps for overcoming obstacles, kindly note the following:
This is a product which is essentially designed for use indoors on level routes and surfaces. It should
only be used on ramps if they are smooth and no ridges are involved in getting on and off them.
lThey should not be taken over ramps when somebody is sitting in the chair.
FOR YOUR SAFETY
Please note, depending on the chair's configuration, the following safety hints:
lOnly use the wheelchair on level surfaces and in indoor areas.
lIt should not be used on staircases or steps or to pass other obstacles.
lMake regular checks to ensure the parking brakes are working properly.
lEnsure that there are no objects, obstructions or persons come within the range of adjustment
of the back section or the legrest.
LBe careful when using sources of fire such as cigarettes, since they can set the seat and back
covers alight.
LMake sure that the maximum load (140 kg)) is not exceeded.
lNever open a pneumatic spring as it is under high pressure and you could get hurt!
lIf the pneumatic springs (if present on the chair) get damaged, stop using the chair. Contact
your dealer straight away to get it repaired.
lWhen accessories and attachments are used, the chair's characteristics change.
lOnly use original accessories, and only use original spare parts for repairs.
MAKING REGULAR CHECKS
Your wheelchair requires regular checks, like any other technical product. The steps to be taken to
fully enjoy the advantages of your wheelchair even after protracted use, are described below.
•BEFORE USE
Check the castors for visible damage and/or soiling.
Remove the dirt, since it could impair the functioning of the parking brakes.
If a castor is damaged, please use an authorised workshop to repair it.
•APPROX. EVERY 8 WEEKS
Depending on the frequency of use, kindly check the following:
- Moving parts on the legrest (if there is one)

E
ALESIA
06/2009
13
- Moving parts on the tipping mechanism (if there is one)
- The condition of the covers
- That the armrest adjustment, seat angling and back adjustment are working properly
•APPROX. EVERY 6 MONTHS
Depending on the frequency of use check the following:
- Cleanness
- General condition
- That the screws are tight
- That the steering castors / brakes are working properly
If the rotation resistance is too great, clean the bearings of the steering wheels. If this
is insufficient, kindly consult your dealer.
INSPECTION
Depending on the amount of use, in principle we recommend inspections every two years, but at least
before usage is resumed. The following checks, at least, must be performed and documented by
authorised persons:
•Check the frame parts for plastic deformation and reduced functioning.
•Visual inspection of damage to the paintwork (danger of corrosion)
•Visually check the covers for damage
•Check the castors work properly (run freely, run straight, parking brakes)
•Check that all screws and bolts are tight and well-seated
•The greasing condition of metal joints of movable parts
•Visually check all plastic parts for tears and brittle spots
•Check the legrest works properly (locking, load, deformation, wear and tear caused by weight,
adjustment lever)
•Check, including visually, that the pneumatic springs work (incl. the adjusting lever)
•Completeness of the delivery condition
•Instruction manual available?
The service must only be confirmed in the service plan when at least the above-mentioned aspects
have been checked. If your specialist dealer does not perform the required services, then contact the
manufacturer. We shall gladly refer you to authorised specialist dealers in your area.
The manufacturer is not liable for damage caused by lack of inspections or poor inspections.
CARE
Your wheelchair requires regular care to keep it in a pleasant condition. To do this, note the following:
lNever use steam or pressure jets.
•COVERS
Clean the covers with a cloth moistened by hot water. You can remove stubborn dirt by washing with a
mild commercial detergent. Stains can be removed by using a sponge or a soft brush. Do not use
sharp brushes or any other pointed objects for cleaning.
LDo not use strong cleaning liquids like solvents, nor use hard brushes.
lWe do not accept liability for damage caused by the use of improper cleaning liquids.
lDo not allow the covers to get too wet.
•PLASTIC PARTS
Clean all plastic parts with commercial plastic cleaners. Take note of any specific product information.
•SURFACE LAYERS
The high quality of the surface layer guarantees optimal protection against corrosion. If the outer layer
has been damaged by scratches or otherwise, you can protect the area by applying varnish obtainable
from your specialist dealer. Occasional greasing of the movable parts will ensure that you enjoy your
wheelchair for a long time.

E
ALESIA
06/2009
14
To guarantee the long-term preservation of your wheelchair, we recommend that you take it to your
specialist dealer for inspection every two years. These inspections can be confirmed in the "Service
plan" section.
lThe manufacturer does not accept liability for any damage/injury caused by inadequate
servicing and care.
DISINFECTION
Disinfection should only be carried out by a trained hygienist or by someone they appoint. All of the
parts can be disinfected by scrubbing. In principle all surfaces of a system or a product must be
disinfected before handing it over to a new user or when infections are detected in the user. Then the
measures of the Federal Epidemic Law must be applied.
LWear suitable protective clothing because the disinfectants can irritate the skin on contact. For
this purpose you should also take note of the product information for the solutions concerned.
LYou employ unauthorised persons at your own risk.
LNo liability is accepted by the manufacturer of the wheelchair for damage and injury caused by
the improper handling of disinfectants.
All steps taken for disinfection and its components or other accessory parts are recorded in a
disinfection report which contains at least the following information with product documentation
appended:
Table 2 – Example of a disinfection book
Date of the
disinfection
Reason
Specification
Substance and concentration
Signature
Abbreviations used in column 2 (reason):
V = suspected infection IF = infection case W = repetition I = inspection
We recommend the following disinfectants for scrubbing (based on the list of the Robert Koch Institute, RKI):
Surface
disinfection
(scrub-
washing
Disinfecting excretions
1 part sputum or stool + 2 parts
diluted solution or 1 part urine + 1
part diluted solution
Washing-
disinfection
disinfectio
n)
Sputum
Stools
Urine
Diluted solution
Time to take effect
Diluted solution
Time to take effect
Diluted solution
Time to take effect
Diluted solution
Time to take effect
Diluted solution
Time to take effect
Active substance
Name
%
Hrs.
%
Hrs.
%
Hrs.
%
Hrs.
%
Hrs.
Effectiv
e range
Manufacturer
or
Supplier
Amocid
1
12
5
6
5
4
5
6
5
2
A
Lysoform
Gevisol
0,5
12
5
4
5
4
5
6
5
2
A
Schülke & Mayr
Helipur
6
4
6
4
6
6
6
2
A
B.Braun
m-cresol soap
solution DAB 6
1
12
5
4
A
Phenol or
phenol derivatives
Mucocit-F 2000
1
12
A
Merz
Chloramine-T DAB
9
1,5
12
2,5
2
5
4
A1 B
Clorina
1,5
12
2,5
2
5
4
A1 B
Lysoform
Chlorine, organic or
inorganic substances
with active chlorine
Trichlorol
2
12
3
2
6
4
A1 B
Lysoform
Apesin AP1002
4
4
AB
Tana Professional
Pure Dismozon2
4
1
AB
Bode Chemie
Perform2
3
4
AB
Schülke & Mayr
Percompounds
Wofesteril2
2
4
AB
Kesla Pharma
Aldasan 2000
4
4
AB
Lysoform

E
ALESIA
06/2009
15
Antifect FD 10
3
4
AB
Schülke & Mayr
Antiseptica
Surface
Disinfection 7
3
6
AB
Antiseptica
Apesin AP30
5
4
A
Tana Professional
Bacillocid Spezial
6
4
AB
Bode Chemie
Buraton 10F
3
4
AB
Schülke & Mayr
Desomed A 2000
3
6
AB
Desomed
Hospital dis-
infection cleaner
8
6
AB
Dreiturm
Desomed Perfekt
7
4
A
Desomed
Formaldehyde
solution DAB 10
(formalin)
1,5
12
3
4
AB
Incidin perfekt
1
12
3
4
AB
Ecolab
Incidin Plus
8
6
A
Ecolab
Kohrsolin
2
12
3
4
AB
Bode Chemie
Lysoform
4
12
5
6
AB
Lysoform
Lysoformin
3
12
5
6
AB
Lysoform
Lysoformin 2000
4
6
AB
Lysoform
Melsept
2
12
4
6
AB
B.Braun
Melsitt
4
12
10
4
AB
B.Braun
Minutil
2
12
6
4
AB
Ecolab
Multidor
3
6
AB
Ecolab
Nüscosept
5
4
AB
Dr.Nüsken Chemie
Optisept
7
4
A
Dr.Schumacher
Pursept-FD
7
4
AB*
Merz
Formaldehyde
and/or other
aldehydes or
derivatives
Ultrasol F
3
12
5
4
AB
Fresenius
Amphotensid
Tensodur 103
2
12
A
MFH Marienfelde
Alkaline solution
Lime-wash3
20
6
A3 B
1Insufficiently effective against myco-bacteria when disinfecting surfaces, especially in the presence of blood. 2Not suitable for disinfecting blood-contaminated or porous
surfaces (e.g. raw wood). 3Useless for tuberculosis; preparation of lime-wash: 1 part dissolved lime (calcium hydroxide) + 3 parts water. *Virus effectiveness tested in compliance
with the RKI test method [German Federal Health Circular 38 (1995) 242] .
A:suitable for killing vegetative bacterial germs including myco-bacteria as well as fungi, including fungal spores.
B:suitable for deactivating viruses.
The current state of the disinfectants included in the RKI list can be ascertained at the Robert Koch
Institute (Home page: www.rki.de).
Kindly consult your specialist dealer if you have further queries about disinfection; he will
gladly assist you.
STORAGE
•Store in a dry place (between + 5 °C and + 45 °C).
•The relative humidity of the air should be between 30% and 70%.
•Air pressure between 700 hPa and 1060 hPa.
•Ensure there is protection against corrosion (e.g. salt water, sea air, sand, dust) by providing
sufficient covering or packaging.
•Store all removed parts together in one place (or mark them if necessary) to avoid mixing up
with other products when re-assembling.
•No component must be stored with a heavy weight on it.
DISPOSAL
To dispose of the wheelchair, contact a local waste disposal company or return the product to your
dealer who, after some hygiene measures, will be able to return it to the manufacturer, who will take
dispose of it and recycle it properly, separated into material groups.
Packaging materials can be taken to suitable tips or recycling centres, or to your dealer.
Your dealer will also be able to advise you should you have any queries.

E
ALESIA
06/2009
16
GUARANTEE
Excerpt from the "General business conditions":
(…)
5. The guarantee period for warranty claims is 24 months.
(…)
Claims are invalid when:
- the agreed condition is only minimally deviated from
- usability is only minimally impaired
- wear and tear is normal
- faults are due to improper assembly or neglected maintenance
- faults are due to improper use
- errors are due to improper handling by customers or their contractual partners or service centres
- damage that arises after the transfer of risk as a result of faulty or negligent handling, excessive
demands, unsuitable equipment, faulty assembly or that are due to particular external factors that are
not assumed under the contract.
(…)
CONFORMITY
The ALESIA wheelchair complies with the requirements of the European directive:
- 93/42/EEC (Medical Products Directive)
and the product norms:
- (DIN) EN 12182: 1999 (where applicable)
- (DIN) EN 12183: 1999 (where applicable)

F
TABLE DES MATIÈRES
Chapitre Page
Table des matières ............................................................................................................................1
Avant-propos......................................................................................................................................2
Domaine d'utilisation ..........................................................................................................................2
Généralités.........................................................................................................................................2
Pièces Alesia .....................................................................................................................................3
Caractéristiques techniques...............................................................................................................3
Assemblage .......................................................................................................................................4
•Siège ...........................................................................................................................................4
•Dossier ........................................................................................................................................4
•Appui-tête ....................................................................................................................................5
Inclinaison du siège ...........................................................................................................................5
Réglage du dossier ...........................................................................................................................6
Accoudoirs .........................................................................................................................................7
Repose-pieds.....................................................................................................................................7
Frein de stationnement central ..........................................................................................................8
Roue directionnelle ............................................................................................................................8
Accessoires........................................................................................................................................9
•Porte documents (B79)................................................................................................................9
•Coussins (L04) ............................................................................................................................9
•Support pour poche de perfusion (B52) ......................................................................................10
•Support à usages multiples .........................................................................................................10
•Repose-jambes réglable..............................................................................................................10
•Table thérapeutique (B12)...........................................................................................................11
•Support de poche à urine ............................................................................................................11
Transport............................................................................................................................................11
Transport via des rampes ..................................................................................................................12
Pour votre sécurité.............................................................................................................................12
Contrôles réguliers.............................................................................................................................13
Inspection...........................................................................................................................................13
Entretien.............................................................................................................................................13
Désinfection .......................................................................................................................................14
Stockage ............................................................................................................................................16
Recyclage ..........................................................................................................................................16
Garantie .............................................................................................................................................16
Conformité .........................................................................................................................................16
Avertissement pour les revendeurs :
Ce mode d’emploi fait partie intégrante du produit et doit être remis avec le produit.
Édition : 06/2009
Tous droits, également ceux de la traduction, réservés.
Aucune partie de ce mode d’emploi ne peut être reproduite sous quelque forme que ce soit (impression,
photocopie, microfilm ou autre procédé) sans l’autorisation écrite de l’éditeur ou traitée, reproduite ou diffusée à
l’aide de systèmes électroniques.
!N.V. Vermeiren N.V., 2009

F
ALESIA
06/2009
2
AVANT-PROPOS
Nous tenons tout d’abord à vous remercier pour la confiance que vous nous accordez en optant pour
l’un de nos produits.
Les produits Vermeiren sont le résultat de longues années d'expérience et de recherches. Pendant la
phase de développement, nous avons attaché une importance particulière à la simplicité d’emploi et
d’entretien.
La durée de vie du produit dépend dans une large mesure du maintien en bon état de celui-ci pendant
son utilisation. Ce mode d’emploi doit vous aider à vous familiariser avec l’utilisation de votre fauteuil
de repos. Vous trouverez en outre des conseils vous indiquant la manière de maintenir votre produit
en bon état et de lui assurer une longue durée de vie.
Ce mode d'emploi correspond au dernier stade de développement du produit. La société Vermeiren
se réserve toutefois le droit d’apporter des modifications sans obligation d’adapter ou de remplacer les
modèles livrés précédemment.
Gardez toujours à l’esprit qu'en respectant nos instructions, vous maintiendrez votre fauteuil de repos
dans le meilleur état de fonctionnement possible, et ce même après une longue utilisation.
Si vous avez d’autres questions, veuillez vous adresser à votre revendeur.
DOMAINE D’UTILISATION
En ayant porté votre choix sur le fauteuil de transport ALESIA, vous avez acheté ce qui se fait de
mieux en termes de concept et de confort. Le fauteuil de transport ALESIA est exclusivement destiné
à une utilisation en intérieur. L’utilisation de ce produit à l’extérieur est tout à fait déconseillée. Les
personnes qui doivent être transportées sur le fauteuil doivent au minimum présenter un contrôle
suffisant de leur corps et ne pas souffrir de trouble de l'équilibre, au niveau de la stabilité latérale, sans
que des mesures ne soient prises pour les maintenir. Le fauteuil de repos ne doit pas être utilisé
comme échelle, ni pour reposer des charges chaudes, froides ou lourdes, ni même pour le transport
d'objets. Lisez attentivement ce mode d’emploi pour vous familiariser avec votre produit.
Les équipements permettent une utilisation en cas de mobilité réduite due à :
!paralysies/faiblesses (en cas de conservation du contrôle du corps)
!lésions des articulations
!maladies, comme par exemple l’insuffisance cardiaque et circulatoire
Quant aux contre-indications, il y a lieu de tenir compte des facteurs suivants :
!taille et poids (charge max. limitée à 140 kg)
!état physique et mental
!environnement
Aucune garantie ne peut être donnée si le produit n’est pas utilisé dans les conditions
précitées et pour l’objet auquel il est destiné.
GÉNÉRALITÉS
Le cadre du fauteuil ALESIA est en acier de grande qualité, recouvert d'un revêtement par
pulvérisation. L'utilisation de revêtements en similicuir permet un nettoyage et un entretien faciles. Les
systèmes de sièges ont été formés pour votre confort d'après des conditions d'ergonomie.
L’assiette du système de siège, du dossier et du repose-jambes est réglable à l’aide d’un cylindre
pneumatique.