Vestil WL-100 User manual

Rev.12/9/2013WL‐WK,Manual
Copyright2013VestilManufacturingCo. Page1of2

WL‐100WheelKit(WL‐WK):
Unitsequippedwithawheelkitinclude4casters(2swivel‐typeand2rigid)andadetachable
handle.
Atotalof8“bulldog”couplersareweldedtoelementsoftheframe.Thesecouplersprovidethe
meansforattachingthecasterstothetable.
Fourbulldogs(seeitems1‐4inthediagrambelow)areattachedtotheframeinlocationswherethe
casterscannotcontacttheground.Thecastersmustbesecuredtothesebulldogswheneverthe
tableisinuse.
DONOTapplyaloadtothetabletopunlessthecastersareinthestoragebulldogs.
Theotherbulldogs(items5‐8)areattachedtotheframeinlocationswherethecasterswillcontact
thegroundwhenthetableislowered(seeFIG.3onp.2).
Castersarepinnedtothebulldogswith3/8in.x45/8in.clevispinsandhairpinclips.Tosecureacaster
inaparticularbulldog,removethehairpinclipfromtheendoftheclevispinandthenremovethe
clevispinfromthebulldog.Placethemountingbracketofthecasterwithinthebulldog;then
reinserttheclevispinandsecureitinplacebyinsertingahairpinclipthroughtheholeintheendof
theclevis.




































 
Swivelcaster(GFN‐4/2.5)

Rigidcaster(GFN‐4/2‐R)

3/8in.x45/8in.clevispin

Hairpinclip

3
4
5
2
1
678

Swivelcasters:
Storeinbulldogs3&4;
Attachtobulldogs7&
8tomovetable.

Rigidcasters:
Storeinbulldogs1&2;
Attachtobulldogs5&6
tomovetable.
FIG.1:Locationsofbulldogs
Detachable
handle



Rev.12/9/2013WL‐WK,Manual
Copyright2013VestilManufacturingCo. Page2of2
















FIG.2:Castersstoredinbulldogs1‐4.Attachhandletoreceivers




EachreceiverhasaspringpinasshowninFIG.2B.Aloopof
cableconnectsthepins.Onesideofthelooppassesthrougha
smallring.Toretractthespringpins,pulltheringawayfrom
thetable.
Toinstallthehandle,pulltheringtoretractthespringpins;
inserttheendsofthehandleintothereceivers;thenrelease
thepins.Alignthepinholesintheendsofthehandlewiththe
springpinstolockthehandleintoplace.
FIG.3:Castersinbulldogs5‐8.
 

NOTE:DONOTmovecastersbetweenbulldogsunlessthemaintenancepropsaredeployed.Thetabletop
mustbesecurelysupportedbytheprops.
Swivelcastersin
storagebulldogs
(3&4)Rigidcastersinstorage
bulldogs(1&2)
Rigidcastersinbulldogs5&6
Swivelcastersin
bulldogs7&8

Spring
pin
Receiver
FIG.2B:Receiverandspringpin

Pinholein
endofhandle