Videotec HOV User manual

ENGLISH ITALIANO FRANÇAIS DEUTSCH
РУССКИЙ
EN
English - Instructions manual
IT
Italiano - Manuale di istruzioni
FR
Français - Manuel d’instructions
DE
Deutsch - Bedienungslanleitung
RU
Русский -   
HOV
Side opening aluminium camera housing

EN
English - Instruction manual
ENGLISH
HOV
Side-opening aluminium camera housing

Instruction manual - English - EN
3MNVCHOV32_1702_EN
Contents
ENGLISH 1
1 About this manual ......................................................................................................... 4
1.1 Typographical conventions.................................................................................................................................. 4
2 Notes on copyright and information on trademarks.................................................. 4
3 Safety rules..................................................................................................................... 4
4 Identication.................................................................................................................. 5
4.1 Product description and type designation..................................................................................................... 5
4.2 Product marking ...................................................................................................................................................... 5
5 Preparing the product for use ...................................................................................... 6
5.1 Unpacking.................................................................................................................................................................. 6
5.2 Contents...................................................................................................................................................................... 6
5.3 Safely disposing of packaging material........................................................................................................... 6
5.4 Preparatory work before installation................................................................................................................ 6
5.4.1 Attaching the bracket............................................................................................................................................................ 6
6 Installation ..................................................................................................................... 7
6.1 How to open the housing..................................................................................................................................... 7
6.2 How to install the camera..................................................................................................................................... 7
6.3 Board description .................................................................................................................................................... 8
6.4 Connection of the power supply line............................................................................................................... 8
6.5 Installation of the version with double lter for air renewal.................................................................... 9
6.6 Installation of the version with wiper............................................................................................................... 9
6.7 Desiccant bag............................................................................................................................................................ 9
7 Accessories................................................................................................................... 10
7.1 Heater.........................................................................................................................................................................10
7.1.1 Heater installation.................................................................................................................................................................10
7.2 Camera power supply..........................................................................................................................................10
7.2.1 Camera power supply installation...................................................................................................................................10
7.3 Blower........................................................................................................................................................................11
7.3.1 Blower installation.................................................................................................................................................................11
8 Instructions for normal operation.............................................................................. 12
9 Cleaning ....................................................................................................................... 12
9.1 Cleaning the window and plastic parts.........................................................................................................12
10 Disposal of waste materials...................................................................................... 12
11 Technical data ............................................................................................................ 13
11.1 General....................................................................................................................................................................13
11.2 Mechanical.............................................................................................................................................................13
11.3 Electrical .................................................................................................................................................................13
11.4 Environment..........................................................................................................................................................13
11.5 Certications.........................................................................................................................................................13
12 Technical drawings .................................................................................................... 14

EN - English - Instruction manual
4 MNVCHOV32_1702_EN
1 About this manual
Read all the documentation supplied carefully before
installing and using this unit. Keep the manual in a
convenient place for future reference.
1.1 Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the
power supply before proceeding with any
operation, unless indicated otherwise.
CAUTION!
Medium level hazard.
This operation is very important for the
system to function properly. Please read
the procedure described very carefully and
carry it out as instructed.
INFO
Description of system specications.
We recommend reading this part carefully
in order to understand the subsequent
stages.
2 Notes on copyright and
information on trademarks
The mentioned names of products or companies are
trademarks or registered trademarks.
3 Safety rules
CAUTION! Device installation and
maintaining must be performed by
specialist technical sta only.
CAUTION! The electrical system to which
the unit is connected must be equipped
with an automatic bipolar circuit breaker.
The circuit breaker for main supply
voltage phase units must have a level of
intervention of 20A max. The circuit breaker
for low voltage units must have a level of
intervention of 6A max. This circuit breaker
must be of the Listed type. The minimum
distance between the circuit breaker
contacts must be 3mm (0.1in). The circuit
breaker must be provided with protection
against the fault current towards the
ground (dierential) and the overcurrent
(magnetothermal).
• The manufacturer declines all responsibility
for any damage caused by an improper use
of the appliances mentioned in this manual.
Furthermore, the manufacturer reserves the right
to modify its contents without any prior notice.
The documentation contained in this manual has
been collected and veried with great care. The
manufacturer, however, cannot take any liability
for its use. The same thing can be said for any
person or company involved in the creation and
production of this manual.
• Before starting any operation, make sure the
power supply is disconnected.
• Be careful not to use cables that seem worn or old.
• Never, under any circumstances, make any
changes or connections that are not shown in
this handbook. Improper use of the appliance
can cause serious hazards, risking the safety of
personnel and of the installation.
• Use only original spare parts. Non-original spare
parts could cause re, electrical discharge or other
hazards.
• Before proceeding with installation, check the
supplied material to make sure it corresponds
to the order specication by examining the
identication labels (4.2 Product marking, page 5).

Instruction manual - English - EN
5MNVCHOV32_1702_EN
• This device was designed to be permanently
secured and connected on a building or on a
suitable structure. The device must be permanently
secured and connected before any operation.
• Comply with all the national standards during the
device installation.
• Installation category (also called Overvoltage
Category) species the level of mains voltage
surges that the equipment will be subjected to.
The category depends upon the location of the
equipment, and on any surge voltage protection
provided. Equipment in an industrial environment,
directly connected to major feeders/short branch
circuits, is subjected to Installation Category
III. If this is the case, a reduction to Installation
Category II is required. This can be achieved by
use of an insulating transformer with an earthed
screen between primary and secondary windings,
or by tting UL listed Surge Protective Devices
(SPDs) from live to neutral and from neutral to
earth. Listed SPDs shall be designed for repeated
limiting of transient voltage surges and the
following rated operation conditions: Type 2 (SPDs
permanently connected to the power network and
intended for installation on the load side of the
service equipment); Nominal Discharge Current
(In) 20kA min. For example: FERRAZ SHAWMUT,
STT2240SPG-CN, STT2BL240SPG-CN rated
120Vac/240Vac, (In=20kA). Maximum distance
between installation and reduction is 5m.
• Any device which could be installed inside the
product must comply with the current safety
standards.
• For all connections, use cables that are able to
withstand temperatures of at least 75°C (167°F).
• A power disconnect device must be included
in the electrical installation, and it must be very
quickly recognizable and operated if needed.
4 Identication
4.1 Product description and type
designation
Robust aluminium housing designed to simplify
the installation and service, and guarantee total
protection against all environmental conditions.
Its size makes it ideal for housing various
combinations of standard cameras with xed or
compact zoom lenses.
Very easy to install thanks to the side-opening system
that allows the full access to the camera, lenses and
all internal connections.
The numerous available accessories, like heater,
camera power supply, blower and air lter, wiper and
washer can satisfy any installation application.
4.2 Product marking
See the label attached to the product.

EN - English - Instruction manual
6 MNVCHOV32_1702_EN
5 Preparing the product for
use
Any change that is not expressly approved
by the manufacturer will invalidate the
guarantee.
5.1 Unpacking
When the product is delivered, make sure that the
package is intact and that there are no signs that it
has been dropped or scratched.
If there are obvious signs of damage, contact the
supplier immediately.
When returning a faulty product we recommend
using the original packaging for shipping.
Keep the packaging in case you need to send the
product for repairs.
5.2 Contents
Check the contents to make sure they correspond
with the list of materials as below:
• Housing
• Housing equipment:
• Allen wrench
• Spacers
• Cable glands gaskets
• Cable glands (x3)
• Bolts and screws
• Instruction manual
• Desiccant bag
5.3 Safely disposing of packaging
material
The packaging material can all be recycled. The
installer technician will be responsible for separating
the material for disposal, and in any case for
compliance with the legislation in force where the
device is to be used.
5.4 Preparatory work before
installation
5.4.1 Attaching the bracket
The product must be fastened with suitable
equipment. The fastening means must
guarantee the mechanical seal when a force
equal to at least 4 times the weight of the
device is applied.

Instruction manual - English - EN
7MNVCHOV32_1702_EN
6 Installation
6.1 How to open the housing
Loosen the 2 screws on the side, turn the cover and
the upper half of the body about the opening hinge
axis.
Fig. 1
After installation and wiring, close the
product again.
6.2 How to install the camera
Power supply can be provided by the board
supplied with the product. Make sure the
voltage values are appropriate.
Open the housing as described in the relative chapter
(6.1 How to open the housing, page7).
Partially loosening the fastening screws (01).
Remove the internal slide (02) by sliding it until the
holes coincide with the slide fastening screws.
Fasten the camera with the 1/4" screw (03). To
position the camera and lens correctly, if necessary,
use the supplied spacers. (04).
01
03 02
03
Fig. 2
Reposition the internal slide and tighten the screws
that had been loosened previously.
Remove the conductors protective sheathing and
connect them to terminal (J5, 6.3 Board description,
page8).
The camera’s power supply cable conductors must be
tied up with a cable tie next to the terminal. Keep the
signalling and power supply cables separated from
each other.

EN - English - Instruction manual
8 MNVCHOV32_1702_EN
6.3 Board description
The board may appear dierent to that
illustrated.
Depending on the product version, the
board may not be equipped with all
functions.
BOARD DESCRIPTION
Connector Function
J1 Power supply for the board (VIN)
J2 Auxiliary output (VOUT)
J3 Heater power supply (VOUT)
J4 Tamper switch contacts
J5 Camera power supply (VOUT)
J7 Power supply connector/jumper
J8 Fan power supply (VOUT)
SW1 Tamper switch
Tab. 11From 100Vac a 240Vac, 24Vac o12Vdc.
2Same voltage applied to power supply terminal of the
board (J1).
3Optional.
4Dierent alternatives are available depending on the
version. VOUT = 12Vdc o VOUT = 24Vac, in relation to the
type of power supply installed (7.2.1 Camera power
supply installation, page10). VOUT = VIN, only for hou-
sings powered in 12Vdc or 24Vac, with jumper inserted
(J7).
5To install a power supply in 12Vdc or 24Vac refer to the
relative chapter (7.2.1 Camera power supply installa-
tion, page10).
J1 J4J2J8
J7SW1 J3 J5
Fig. 3
Nominal section of the cables used: from
0.2mm² up to 2.5mm².
6.4 Connection of the power
supply line
CAUTION! The type of cable used must be
compatible with the planned use. Comply
with the national regulations in force on
electrical installation.
Connect the safety earth to the relative
terminal of the J1 connector.
Earth cable should be about 10mm longer
than the other two, so that it will not be
disconnected accidentally if pulled.
Insert the cables inside the housing using the cable
glands. The cable glands are suitable for conductors
with diameters of between 5mm and 10mm. The
section of the cable inside the housing must be
suciently long to allow connection. Suitably lock
the cable glands.
Remove the conductors protective sheathing and
connect them to terminal (J1, 6.3 Board description,
page8).

Instruction manual - English - EN
9MNVCHOV32_1702_EN
6.5 Installation of the version
with double lter for air renewal
During installation pay attention to the
orientation of the air inlet lter ns.
Fig. 4
Depending on the angle of inclination of the housing,
the orientation of the lter ns must prevent water
penetrating in case of rain:
To guarantee weatherproof protection, install the
housing on the support following the inclination
limits as shown in the picture.
0˚
45°
45°
Fig. 5Maximum tilt of the transversal axis: 0°.
Maximum tilt of the longitudinal axis: ±45°.
6.6 Installation of the version
with wiper
Open the housing as described in the relative chapter
(6.1 How to open the housing, page7).
Identify the terminal of the wiper board.
P
S
C
Fig. 6
Connect the wiper board to the power supply mains
as shown in the gure.
PSC
L
N~
Fig. 7
Nominal section of the cables used: from
0.2mm² up to 2.5mm².
Pressing the button activates the wiper. When the
button is released the wiper blade will return to the
rest position.
If you have a receiver with the Wiper control function,
connect the SW, PER and COM terminals respectively
to terminals S, P and C of the board.
6.7 Desiccant bag
Take the dessicant salt bag out of its pack and insert it
into the product.

EN - English - Instruction manual
10 MNVCHOV32_1702_EN
7 Accessories
For further details on conguration and
use, refer to the relative manual.
7.1 Heater
7.1.1 Heater installation
Open the housing as described in the relative chapter
(6.1 How to open the housing, page7).
Fix the heater kit to the prearranged points on the
body of the housing.
The pre-wired heating element (01) should be
positioned between the 2 dissipators (02) before
attachment to ensure contact and hence guarantee
correct heat transmission.
Pass the heating wiring under the slide to x the
camera.
02
01 02
Fig. 8
At the end of istallation, connect the wiring to
the terminal (power supply connector, 6.3 Board
description, page8).
Reposition the internal slide and tighten the screws
that had been loosened previously.
7.2 Camera power supply
7.2.1 Camera power supply installation
Not usable in housings with wiper device
installed.
Pay attention to the voltage used to power
the circuit. Depending on requirements use
the correct power supply kit.
Usable power supplies:
• IN from 100Vac up to 240Vac, 50/60Hz - OUT
12Vdc, 1.25A
• IN 230Vac, 50Hz - OUT 24Vac, 50Hz, 400mA
Fig. 9Camera power supply.

Instruction manual - English - EN
11MNVCHOV32_1702_EN
Open the housing as described in the relative chapter
(6.1 How to open the housing, page7).
Fix the support bracket (02) using the screw (01).
Place the power supply (03) on the support bracket.
Secure it all with the screws (04) and the corner xing
bracket (5).
04
02
03
05
01
Fig. 10
Plug the multipolar female connector into the
corresponding male connector (J7, 6.3 Board
description, page8).
Fig. 11
7.3 Blower
7.3.1 Blower installation
Not usable in versions with double lter for
air renewal and wiper.
Pay attention to the voltage used to power
the circuit. Depending on requirements use
the correct power supply kit.
The blower kit should be assembled
according to the instructions to ensure a
correct air circulation inside the housing.
Open the housing as described in the relative chapter
(6.1 How to open the housing, page7).
Fix the blower using the corner bracket and screws.
01
02
Fig. 12
Plug the multipolar female connector into the
corresponding male connector (J8, 6.3 Board
description, page8).

EN - English - Instruction manual
12 MNVCHOV32_1702_EN
8 Instructions for normal
operation
Do not use the wiper if the outside
temperature is below 0°C or in case of ice.
9 Cleaning
9.1 Cleaning the window and
plastic parts
Avoid ethyl alcohol, solvents, hydrogenated
hydrocarbide, strong acid and alkali. Such
products may irreparably damage the
surface.
We recommend using a soft cloth with neutral soap
diluted with water or specic products to clean the
glasses lenses.
10 Disposal of waste
materials
This symbol mark and recycle system
are applied only to EU countries and not
applied to other countries of the world.
Your product is designed and manufactured with
high quality materials and components which can be
recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed of
separately from your household waste.
Please dispose of this equipment at your local
Community waste collection or Recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.

Instruction manual - English - EN
13MNVCHOV32_1702_EN
11 Technical data
11.1 General
Constructed from aluminium
Sunshield in ABS
Epoxypolyester powder painting, RAL9002 colour
Stainless steel external screws
11.2 Mechanical
Internal usable area (WxH): 100x70mm (3.9x2.7in)
Internal usable length (with or without accessories):
250mm (9.8in)
Cable glands: 3xM16
Housing window
• Material: Extra clear glass
• Dimensions (WxH): 118x75mm (4.6x2.7in)
Unit weight: 3kg (6.6lb)
11.3 Electrical
Supply voltage/Current consumption (empty
version):
• From 12Vdc up to 24Vdc, 1A max
• From 12Vac up to 24Vac, 1A max, 50/60Hz
• From 120Vac up to 230Vac, 400mA max, 50/60Hz
Supply voltage/Current consumption (version with
heater, Ton 15°C±3°C (59°F ±5°F), To 22°C±3°C
(72°F±5°F)):
• From 12Vdc up to 24Vdc, 3A max
• From 12Vac up to 24Vac, 3A max, 50/60Hz
• From 120Vac up to 230Vac, 400mA max, 50/60Hz
Supply voltage/Current consumption (version with
heater fan assistant, continuous duty):
• 12Vdc, 400mA max
• 24Vac, 200mA max, 50/60Hz
• From 100Vac up to 240Vac, 40mA max,
50/60Hz (with wide-range power supply)
Supply voltage/Current consumption (version with
blower and thermostat for models with double
lter for air renewal, Ton 35°C±3°C (95°F±5°F), To
20°C±3°C (71°F±5°F)):
• 12Vdc, 400mA max
• 24Vac, 200mA max, 50/60Hz
Supply voltage/Current consumption (version with
integrated wiper):
• 24Vac, 1.85A max, 50/60Hz
• 230Vac, 40mA max, 50/60Hz
Camera power supply:
• IN from 100Vac up to 240Vac, 50/60Hz - OUT
12Vdc, 1.25A
• IN 230Vac, 50Hz - OUT 24Vac, 50Hz, 400mA
11.4 Environment
For installation indoors and outdoors
Operating temperature (with heater): from -20°C
(-4°F) up to +65°C (149°F)
11.5 Certications
Electrical safety (CE): EN60950-1, IEC60950-1
Electromagnetic compatibility (CE): EN50130-4,
EN61000-6-3, EN55022 Classe B
Outdoor installation (CE): EN60950-22, IEC 60950-22
IP protection degree: EN60529
• IP66/IP67 (with cable glands)
• IP66/IP67 (with bracket with internal cable
channel, with sealing rings)
• IP55 (with bracket with internal cable channel)
• IP44 (with double lter for air renewal)
IK protection degree (for models HOV32K1A084,
HOV32K2A084): EN62262
• IK10
Salty fog resistance: to 1000 hours (ISO9227)
UL certication: cULus Listed, TYPE 4X (except for
versions with double lter for the air exchange,
HOV32K1A018, HOV32K2A016, HOV32K2A017,
HOV32K2A147, and the version with wiper 230Vac,
HOV32K1A100)
EAC certication

EN - English - Instruction manual
14 MNVCHOV32_1702_EN
12 Technical drawings
The dimensions of the drawings are in millimetres.
76
9827
131
160
213
70 40
188
113
60
8888
400
225
13
3939 62
140
= =
53
514 176
100
70
250
70
A
A
B
B
A - A
B - B
90˚
R100
400
430
412
USABLE
AREA
USABLE AREA
Fig. 13 HOV.

MNVCHOV32_1702_EN
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. [phone] - Fax [phone]
Email: [email protected]
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. [phone] - Fax [phone]
Email: [e-mail]
Asia Pacic Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. [phone] - Fax [phone]
Email: [e-mail]
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. [phone] - Fax [phone]
Email: [e-mail]
www.videotec.com

IT
Italiano - Manuale di istruzioni
ITALIANO
HOV
Custodia per telecamera in alluminio ad apertura laterale