Videotec MAXIMUS MVX User manual

EN
English - Instruction manual
IT
Italiano - Manuale di istruzioni
FR
Français - Manuel d’instructions
DE
Deutsch - Bedienungsanleitung
RU
Русский - Руководство по эксплуатации
PT
Português - Manual de instruções
KO
한국어 - 지침 설명서
ITALIANO
MAXIMUS MVX
High-spec ex-proof Day/Night camera in a compact design

EN
English - Instruction manual
ENGLISH
MAXIMUS MVX
High-spec ex-proof Day/Night camera in a compact design

Instruction manual - English - EN
3MNVCMVXCAM_1645_EN
Contents
ENGLISH 1
1 About this manual ......................................................................................................... 5
1.1 Typographical conventions.................................................................................................................................. 5
2 Notes on copyright and information on trademarks.................................................. 5
3 Identification.................................................................................................................. 5
3.1 Product marking ...................................................................................................................................................... 5
4 Installation ..................................................................................................................... 6
4.1 Range of use.............................................................................................................................................................. 6
4.2 Connection of the power supply line............................................................................................................... 6
4.3 Video cable connection......................................................................................................................................... 7
4.4 Connection of the Ethernet cable ..................................................................................................................... 7
4.5 Signal cable connection........................................................................................................................................ 8
4.5.1 Connecting the telemetry line............................................................................................................................................ 8
4.5.2 Alarm and relay connections............................................................................................................................................... 8
4.5.2.1 Connecting an alarm with dry contact ................................................................................................................................................. 8
4.5.2.2 Relays connection......................................................................................................................................................................................... 8
4.6 Washing system connection................................................................................................................................ 9
4.7 Hardware configuration........................................................................................................................................ 9
4.7.1 Two-way RS-485 TX/RX line.................................................................................................................................................. 9
5 Switching on .................................................................................................................. 9
5.1 First start-up............................................................................................................................................................... 9
6 Configuration............................................................................................................... 10
6.1 OSM interface (On Screen Menu).....................................................................................................................10
6.1.1 Using the OSM........................................................................................................................................................................10
6.1.1.1 How to use the joystick.............................................................................................................................................................................10
6.1.1.2 How to move around the menus..........................................................................................................................................................11
6.1.1.3 How to modify the parameters..............................................................................................................................................................11
6.1.1.4 How to change the numeric fields .......................................................................................................................................................12
6.1.1.5 How to change text....................................................................................................................................................................................12
6.1.2 Configuration via OSM.........................................................................................................................................................14
6.1.3 Main Menu...............................................................................................................................................................................14
6.1.4 Language Selection Menu .................................................................................................................................................14
6.1.5 Camera menu..........................................................................................................................................................................14
6.1.5.1 Advanced Setting Menu...........................................................................................................................................................................15
6.1.5.2 Advanced Setting Menu (Zoom)...........................................................................................................................................................15
6.1.5.3 Advanced Setting Menu (Focus)...........................................................................................................................................................15
6.1.5.4 Advanced Setting Menu (Exposure)....................................................................................................................................................16
6.1.5.5 Advanced Setting Menu (Infrared).......................................................................................................................................................17
6.1.5.6 Advanced Setting Menu (White Balance)..........................................................................................................................................18
6.1.5.7 Advanced Setting Menu (Other)...........................................................................................................................................................18
6.1.6 Display Menu ..........................................................................................................................................................................19
6.1.7 Options Menu.........................................................................................................................................................................19
6.1.7.1 Alarms Menu ................................................................................................................................................................................................20
6.1.7.2 Washer Menu................................................................................................................................................................................................20
6.1.7.3 Test function menu ....................................................................................................................................................................................21
6.1.7.3.1 I/O status menu..................................................................................................................................................................................21

EN - English - Instruction manual
4 MNVCMVXCAM_1645_EN
6.1.7.4 Communication menu..............................................................................................................................................................................22
6.1.8 Default Menu ..........................................................................................................................................................................22
6.1.9 Info Menu .................................................................................................................................................................................22
6.2 Software interface.................................................................................................................................................23
6.2.1 Minimum system requirements.......................................................................................................................................23
6.2.2 Configuration procedure through software................................................................................................................23
6.2.3 Installing the software.........................................................................................................................................................23
6.3 Web interface ..........................................................................................................................................................25
6.3.1 Home Page...............................................................................................................................................................................25
6.3.2 User Controls page................................................................................................................................................................26
6.3.3 Device Parameters Page......................................................................................................................................................27
6.3.4 Device Statistics page..........................................................................................................................................................27
6.3.5 Network Configuration page ............................................................................................................................................27
6.3.6 User Configuration page.....................................................................................................................................................28
6.3.7 Digital I/O Page.......................................................................................................................................................................28
6.3.8 Wiper..........................................................................................................................................................................................28
6.3.9 Washer page............................................................................................................................................................................28
6.3.10 Encoder Parameters page................................................................................................................................................29
6.3.11 Tools Page ..............................................................................................................................................................................29
7 Accessories................................................................................................................... 29
8 Instructions for normal operation.............................................................................. 29
8.1 Enabling the wiper (Wiper)................................................................................................................................29
8.2 Enabling the washer (Washer)..........................................................................................................................29
8.3 Special controls ......................................................................................................................................................30
9 Maintenance ................................................................................................................ 31
9.1 Firmware updating................................................................................................................................................31
9.1.1 Factory Default .......................................................................................................................................................................31
10 Disposal of waste materials...................................................................................... 31
11 Troubleshooting ........................................................................................................ 32
12 Technical data ............................................................................................................ 33
12.1 Camera....................................................................................................................................................................33

Instruction manual - English - EN
5MNVCMVXCAM_1645_EN
1 About this manual
Read all the documentation supplied carefully before
installing and using this unit. Keep the manual in a
convenient place for future reference.
1.1 Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the
power supply before proceeding with any
operation, unless indicated otherwise.
DANGER!
Hot surface.
Avoid contact. Surfaces are hot and may
cause personal injury if touched.
DANGER!
Emission of visible light or infrared.
Can be harmful for eyes. Pay attention to
the provided indications.
CAUTION!
Medium level hazard.
This operation is very important for the
system to function properly. Please read
the procedure described very carefully and
carry it out as instructed.
INFO
Description of system specifications.
We recommend reading this part carefully
in order to understand the subsequent
stages.
2 Notes on copyright and
information on trademarks
The mentioned names of products or companies are
trademarks or registered trademarks.
3 Identification
3.1 Product marking
See the label attached to the product.

EN - English - Instruction manual
6 MNVCMVXCAM_1645_EN
4 Installation
CAUTION! Device installation and
maintaining must be performed by
specialist technical staff only.
The external multi-polar cable shield
(armature) must be earthed.
All disconnected wires must be electrically
isolated.
Two variations of the product are available,
analogue or IP version. Pay attention to the
distinction between the different versions
in the chapters below.
The product comes with a multi-polar cable
or a cable tail for coupling purposes. When
installing the device with the multi-polar
cable, keep at least 250mm free space from
the bottom of the housing to allow for the
minimum curvature radius of the multi-
polar cable.
4.1 Range of use
The installation temperature range is -60°C to +65°C
(-76°F/149°F).
The device operates within a temperature range of
from -40°C and +65°C (-40°F/149°F).
4.2 Connection of the power
supply line
Electrical connections must be performed
with the power supply disconnected and
the circuit-breaker open.
When commencing installation make sure
that the specifications for the power supply
for the installation correspond with those
required by the device.
Check that the power supply is adequately
dimensioned.
The device can be provided with different power
supply voltages. The power supply voltage is
indicated on the product identification label. (3.1
Product marking, page 5).
The multicore cable has the power and earth cables
inside.
Perform the connections following the instructions
reported in the table .
CONNECTION OF THE POWER SUPPLY LINE
Colour Terminals
Power supply 24Vac/from 12Vdc up to 24Vdc
Black 1 (+) L (Phase)
Black 2 (-) N (Neutral)
Yellow/Green
Tab. 1

Instruction manual - English - EN
7MNVCMVXCAM_1645_EN
4.3 Video cable connection
CDS installation type (Cable Distribution
System). The installation is type TNV-1, do
not connect it to SELV circuits.
The operations described in this chapter
can only be performed in the analogue
versions of the product.
The RS-485 cable must always be connected
when configuring the device settings and
performing firmware updates.
A black video cable is included in the multi-polar
cable.
Depending on the version, the video cable requires
the following type of connector:
• Multi-polar cable version: RG 179/U
• Cable tail version: RG 59B/U
4.4 Connection of the Ethernet
cable
The Ethernet cable shield must always be
earthed via the connector. Always use a
shielded RJ45 connector.
The operations described in this chapter
can only be performed in the IP versions of
the product.
An Ethernet cable is included in the multi-polar cable
with the following characteristics: STP (shielded),
Category 5E.
Carry out the connections as described in the table
(according to the standard specifications: TIA/EIA-
568-B).
CONNECTION OF THE ETHERNET CABLE
Pin number Cable color
1 Orange-White
2 Orange
3 Green-White
4 Blue
5 Blue-White
6 Green
7 Brown-White
8 Brown
Tab. 2
The example below shows a typical installation.
Switch
Personal
Computer
Fig. 1

EN - English - Instruction manual
8 MNVCMVXCAM_1645_EN
4.5 Signal cable connection
CAUTION! TNV-1 installation type. The
installation is type TNV-1, do not connect it
to SELV circuits.
SIGNAL CABLE CONNECTION
Colour Function
White RS-485 A (+)
Yellow RS-485 B (-)
Pink Relay 1, Terminal A
Violet (blue, cable
tail version)
Relay 1, Terminal B
Red (brown, cable
tail version)
Alarm/Digital input
Green GND/Common alarm
Grey Reset
Tab. 3
4.5.1 Connecting the telemetry line
Do not connect the serial communication
line in the IP version of the product.
The cables provide access to 1 x RS-485 serial
communication line.
Telemetry lines connect the device to control and
programming units (keyboard or PC).
The product is able to automatically
recognise the type of protocol used
(PANASONIC 850, PELCO D, VIDEOTEC
MACRO).
4.5.2 Alarm and relay connections
The external relay and alarm cable shield
must be earthed.
4.5.2.1 Connecting an alarm with dry contact
In case of free contact alarm make the connection as
shown in the figure.
AL1 COM
Dry contact
Fig. 2AL1: Alarm 1. COM: Common alarms.
The dry contact alarm can be NO (normally open) or
NC (normally closed).
For further information refer to the relative chapter (
6.1.7.1 Alarms Menu, page 20).
4.5.2.2 Relays connection
The relays are usable with the specifications
described below. Working voltage: up
to 30Vac or 60Vdc. Current: 1A max. Use
suitable cable sections with the following
characteristics: from 0.25mm² (23AWG) up
to 1.5mm² (16AWG).
Due to the absence of polarity, both terminals of
the same relay can be used equally with either
alternating or continuous current.
For further information refer to the relative chapter (
6.1.7.1 Alarms Menu, page 20).

Instruction manual - English - EN
9MNVCMVXCAM_1645_EN
4.6 Washing system connection
For further details on configuration and
use, refer to the relative manual.
4.7 Hardware configuration
It is not necessary to configure the device
communication protocol.
4.7.1 Two-way RS-485 TX/RX line
With this setting it is possible to obtain a bi-
directional, half/duplex, communication on the
RS-485-1 line.
Default value: 38400Bd.
If necessary, change the default value of the RS-485
line, which can be done using the PTZ Manager
software available to download for free on the
website support.videotec.com.
TX/RX
RS-485-1
Fig. 3
5 Switching on
The automatic pre-heating (De-Ice) process
could be started whenever the device is
switched on and the air temperature is
below 0°C. This process is used to ensure
that the device works properly even at
low temperatures. The duration ranges
depending on environmental conditions
(from 30 minutes up to 90 minutes).
Complete functionality of the product is guaranteed
up to the following ambient temperature: -40°C.
The product is equipped with a firmware protection
that deactivates the video camera in temperatures of
below -40°C.
The unit is switched on by connecting the power
supply.
To switch off the unit disconnect the power.
5.1 First start-up
Make sure that the unit and other
components of the installation are closed
so that it is impossible to come into contact
with live parts.
Make sure that all parts are fastened down
firmly and safely.

EN - English - Instruction manual
10 MNVCMVXCAM_1645_EN
6 Configuration
The product can be configured using one of the
following tools:
Analogue versions of the product
• OSM interface (On Screen Menu): Configuration via
the text on the analogue video signal.
IP versions of the product.
• Software interface: Configuration via the
application installed on PC.
• Web interface: Configuration via the browser.
6.1 OSM interface (On Screen
Menu)
It is possible to enable the OSM by
connecting the grey and green signal cable
wires for 5 seconds (Tab. 3, page 8).
6.1.1 Using the OSM
During normal operation of the unit, you can activate
the OSM to select and configure advanced functions.
For further information, refer to the manual of the
keyboard used and to the relative chapter. (8.3
Special controls, page 30).
Exit the OSM with Wide Zoom (Zoom-).
6.1.1.1 How to use the joystick
All operations in the menus are carried out using the
joystick.
Left
Up
Right
Down
Fig. 4Browsing the menu.
Exit Confirm
Fig. 5Wide Zoom and Tele Zoom.
If you use control keyboards with 2-axes
joystick, use the Wide Zoom and Tele Zoom
buttons to Exit and Confirm.

Instruction manual - English - EN
11MNVCMVXCAM_1645_EN
6.1.1.2 How to move around the menus
Each page of the OSM shows a list of parameters
or sub-menus that can be selected by the operator.
Move the cursor with the joystick (up and down) to
scroll the various parameters .
ADVANCED
------------------------
1>ZOOM >
2 FOCUS >
3 EXPOSURE >
4 INFRARED >
5 WHITE BALANCE >
6 OTHER >
Fig. 6
The symbol > at the end of a line indicates the
presence of a specific submenu. To enter the
submenu just confirm the menu item. To exit the
submenu use the Exit function (Zoom Wide).
ADVANCED
------------------------
1>ZOOM >
2 FOCUS >
3 EXPOSURE >
4 INFRARED >
5 WHITE BALANCE >
6 OTHER >
Fig. 7
6.1.1.3 How to modify the parameters
Move the cursor to the parameter to be changed and
confirm. The field will start flashing, indicating that it
is in change mode. Use the joystick (up and down) to
show the possible options.
FOCUS
------------------------
1>FOCUS SPEED : 2
2 AUTOFOCUS : N
3 AUTOFOCUS TYPE:TRIGGER
4 SENSITIVITY : NORMAL
Fig. 8
Confirm after having identified the option required.
FOCUS
------------------------
1>FOCUS SPEED : 2
2 AUTOFOCUS : N
3 AUTOFOCUS TYPE:TRIGGER
4 SENSITIVITY : NORMAL
Fig. 9
The field will stop flashing to confirm the selection
made.

EN - English - Instruction manual
12 MNVCMVXCAM_1645_EN
6.1.1.4 How to change the numeric fields
Move the cursor to the parameter to be changed and
confirm.
FOCUS
------------------------
1>FOCUS SPEED : 2
2 AUTOFOCUS : N
3 AUTOFOCUS TYPE:TRIGGER
4 SENSITIVITY : NORMAL
Fig. 10
The first digit in the numeric field to be changed will
flash and the last line of the display will show the
accepted limits for the field. Move in the field (left
and right) and change the sign or the numeric value
(up and down).
FOCUS
------------------------
1>FOCUS SPEED : 2
2 AUTOFOCUS : N
3 AUTOFOCUS TYPE:TRIGGER
4 SENSITIVITY : NORMAL
min:0 max:7
Fig. 11
After making the change, confirm. The cursor returns
to the left and the modified digit will stop flashing.
The field will be forced to the minimum or maximum
value permitted if an unexpected value is entered.
6.1.1.5 How to change text
Move the cursor to the parameter to be changed and
confirm.
ALARM 1
------------------------
STATUS: OPEN
1 TYPE : N.O.
2 ACTION: OFF
3>TEXT : ALARM 1
Fig. 12
The text editing display will open. The arrow symbol
is placed under the character that can be modified,
whilst cursor > is positioned on the left of the
selected character.
EDIT TEXT: AREA
------------------------
Text: TEXT AREA1
↑
>A B C D E F G ERASE
H I J K L M N SAVE
O P Q R S T U EXIT
V W X Y Z 0 1 abc
2 3 4 5 6 7 8
9 : ; . , ? !
‘ + - * / = “
< > SPACE ← →
Fig. 13

Instruction manual - English - EN
13MNVCMVXCAM_1645_EN
You can move inside the menu using the joystick.
EDIT TEXT: AREA
------------------------
Text: TEXT AREA1
↑
A B C D E F G ERASE
H I J K L M N SAVE
O P Q R S T U EXIT
V W X Y Z 0 1 abc
2 3 4 5 6 7 8
9 : ; . , ? !
‘ + - * / = “
< > SPACE ← →
Fig. 14
The Confirm command (Zoom Tele) inserts the
desired character.
EDIT TEXT: AREA
------------------------
Text: TEXT AREA1
↑
A B C D E F G ERASE
H I J K L M N SAVE
O P Q R S T U EXIT
V W X Y Z 0 1 abc
2 3 4 5 6 7 8
9 : ; . , ? !
‘ + - * / = “
< > SPACE ← →
Fig. 15
Use:
• ERASE: Delete the whole text string.
• SAVE: Save the new text before exiting the menu.
• EXIT: Exit the menu.
• abc: Displays lower-case characters.
EDIT TEXT: AREA
------------------------
Text: TEXT AREA1
↑
A B C D E F G ERASE
H I J K L M N SAVE
O P Q R S T U EXIT
V W X Y Z 0 1 abc
2 3 4 5 6 7 8
9 : ; . , ? !
‘ + - * / = “
< > SPACE ← →
Fig. 16
To exit the menu you can also use the Zoom Wide
key.

EN - English - Instruction manual
14 MNVCMVXCAM_1645_EN
6.1.2 Configuration via OSM
It is possible to configure a number of
cameras. Check for compatibility between
the camera and the desired functionality
(12 Technical data, page 33).
The screens for the product setup are illustrated
below.
6.1.3 Main Menu
From the main menu it is possible to enter menus for
configuring the device.
MAIN MENU
------------------------
1>LANGUAGE >
2 CAMERA >
3 DISPLAY SETUP >
4 OPTIONS >
5 DEFAULT >
6 INFO >
Fig. 17
6.1.4 Language Selection Menu
The menu allows you to select the language.
LANGUAGE MENU
------------------------
1>ITALIANO
2 ENGLISH
3 FRANCAIS
4 DEUTSCH
Fig. 18
6.1.5 Camera menu
1. Configuration: Select one of the default
configurations for the camera:
• Standard: Sets the standard operating mode
for the camera.
• Low Light: Sets the operating mode for dimly
lit environments.
• Far Mode: Sets the operating mode for large
areas. It enables the proportional zoom and
the digital zoom.
• Contrast: Set the operating mode to improve
the contrast of the objects visible on the
scene.
• Custom: It indicates that the user has
manually selected the parameters of the
camera.
2. Advanced: This provides access to the submenu
to configure the camera advanced settings.
CAMERA
------------------------
1>CONFIG.: STANDARD
2 ADVANCED >
Fig. 19

Instruction manual - English - EN
15MNVCMVXCAM_1645_EN
6.1.5.1 Advanced Setting Menu
From this menu it is possible to configure the camera
settings in more detail.
1. Zoom: Allows access to the Zoom submenu.
2. Focus: Allows access to the Focus submenu.
3. Exposure: Allows access to the Exposure.
4. Infrared: Allows access to the Infrared
submenu.
5. White Balance: Allows access to the White
Balance submenu.
6. Other: Allows access to the Other submenu.
ADVANCED
------------------------
1>ZOOM >
2 FOCUS >
3 EXPOSURE >
4 INFRARED >
5 WHITE BALANCE >
6 OTHER >
Fig. 20
6.1.5.2 Advanced Setting Menu (Zoom)
1. Zoom Speed: Sets the speed of the zoom. The
speed ranges between 0 (minimum speed) and
7 (maximum speed).
2. Digital Zoom: Enables the digital zoom.
ZOOM
------------------------
1>ZOOM SPEED : 7
2 DIGITAL ZOOM : N
Fig. 21
6.1.5.3 Advanced Setting Menu (Focus)
It allows you to configure the following parameters:
1. Focus Speed: Sets the speed of the Focus. The
speed ranges between 0 (minimum speed) and
7 (maximum speed).
2. Autofocus: Enables or disables the autofocus.
When on, it is to automatically load Autofocus
at any positioning or movement of the zoom,
depending on the selected operating mode.
3. Autofocus Type: Sets the type of Autofocus. The
possible values are:
• Normal: Autofocus is always enabled.
• Interval: The autofocus function is activated
at regular intervals. The Interval is set every 5
seconds.
• Trigger: Autofocus recall on each position
or movement of the zoom. This is the
recommended solution.
4. Sensitivity: Sets the level of sensitivity. The
possible values are:
• Normal: Focusing at the highest possible
speed. This is the recommended solution.
• Low: Slowed-down focusing. It is useful in
case of dim lighting as it makes the image
more stable.
FOCUS
------------------------
1>FOCUS SPEED : 2
2 AUTOFOCUS : N
3 AUTOFOCUS TYPE:TRIGGER
4 SENSITIVITY : NORMAL
Fig. 22

EN - English - Instruction manual
16 MNVCMVXCAM_1645_EN
6.1.5.4 Advanced Setting Menu (Exposure)
It allows you to configure the following parameters:
1. Mode: Sets the type of exposure control
Automatic, Manual, Shutter, Iris and Bright.
2. Shutter Value: Shutter Priority mode enables
manual setting of the shutter operating
time (Shutter Value), enables brightness
compensation (Compensation) and sets a
brightness compensation value (Compensation
value).
3. Iris Value: Iris Priority mode enables
manual setting of diaphragm opening (Iris
Value), enables brightness compensation
(Compensation) and sets a brightness
compensation value (Compensation value).
4. Bright Value: Bright Priority mode enables
manual setting of the desired brightness (Bright
Value).
5. Gain Value: Manual mode enables manual
setting of the shutter operating time (Shutter
Value), diaphragm opening (Iris Value) and the
gain value (Gain Value).
6. Auto Slowshutter: If enabled, this function
automatically increases the exposure time to
improve night vision.
7-8. Compensation, Compensation Value: Sets the
exposure compensation.
9. Gain Limit: Set the maximum gain value the
camera can reach (the greater the gain the
greater the noise level).
EXPOSURE
------------------------
1>MODE : AUTOMATIC
6 AUTO SLOW SHUTTER : Y
7 COMPENSATION : N
8 COMPENSATION VALUE: 7
9 GAIN LIMIT : 4
Fig. 23
The menu dynamically auto-configures based on the
camera installed and the choice made, showing the
parameters on which you can act.
The recommended setting is Automatic.
Automatic mode enables automatic slowing of the
shutter (Auto Slowshutter) based on brightness,
enables brightness compensation (Compensation)
and setting a brightness compensation value
(Compensation Value).
The table below provides the consistency between
the entered values and the effect on the camera lens.
CONSISTENCY BETWEEN THE ENTERED VALUES AND THE EFFECT
ON THE CAMERA LENS
Value Shutter Iris Gain Exposure compen- sation
NTSC PAL
0 1/1 1/1 Closed -3dB -10,5dB
1 1/2 1/2 F28 0dB -9dB
2 1/4 1/3 F22 2dB -7,5dB
3 1/8 1/6 F19 4dB -6dB
4 1/15 1/12 F16 6dB -4,5dB
5 1/30 1/25 F14 8dB -3dB
6 1/60 1/50 F11 10dB -1,5dB
7 1/90 1/75 F9.6 12dB 0dB
8 1/100 1/100 F5 14dB 1,5dB
9 1/125 1/120 F6.8 16dB 3dB
10 1/180 1/150 F5.6 18dB 4.5dB
11 1/250 1/215 F4.8 20dB 6dB
12 1/350 1/300 F4 22dB 7,5dB
13 1/500 1/425 F3.4 24dB 9dB
14 1/725 1/600 F2.8 26dB 10,5dB
15 1/1000 1/1000 F2.4 28dB –
16 1/1500 1/1250 F2 – –
17 1/2000 1/1750 F1.8 – –
18 1/3000 1/2500 – – –
19 1/4000 1/3500 – – –
20 1/6000 1/6000 – – –
21 1/10000 1/10000 – – –
Tab. 4

Instruction manual - English - EN
17MNVCMVXCAM_1645_EN
6.1.5.5 Advanced Setting Menu (Infrared)
It allows you to configure the following parameters:
1. IR Mode: If set to OFF it forces the day mode in
a continuous manner. If set to ON it forces the
night mode in a continuous manner. If set to
Auto, it activates the automatic switching of the
camera.
2. Night Level: Sets the detection threshold of the
light conditions for the night mode switching.
Lower values correspond to lower lighting
levels.
3. Night Delay: Sets the detection time of the
darkness conditions, expressed in seconds,
before switching to night mode.
4. Day Level: Sets the detection threshold of the
light conditions for the day mode switching.
Lower values correspond to lower lighting
levels.
5. Day Delay: Sets the detection time of the
light conditions, expressed in seconds, before
switching to night mode.
6. Cut Off Filter: If it is set on S, the product works
regularly. If it is set on N, the camera does not
switch between night and day mode, but it
works only in day mode.
To avoid false switching, we recommend
choosing the higher day switching
threshold and delay values.
INFRARED
------------------------
1>IR MODE : AUTO
2 NIGHT LEVEL : 5
3 NIGHT DELAY : 5
4 DAY LEVEL : 20
5 DAY DELAY : 30
6 CUT OFF FILTER: Y
Fig. 24
The menu dynamically auto-configures based on the
camera installed and the choice made, showing the
parameters on which you can act.

EN - English - Instruction manual
18 MNVCMVXCAM_1645_EN
6.1.5.6 Advanced Setting Menu (White
Balance)
It allows you to configure the following parameters:
1. Mode: Sets the type of control on White
Balance. The possible values are:
• Automatic: Sets automatic white balance.
This is the recommended solution.
• Manual: Enables manual setting of red and
blue gains.
• Outdoor: Sets fixed red and blue gains for
outdoor applications.
• Outdoor Auto: Sets the values to capture
the scene with a natural white balance for
morning and evening.
• Indoor: Sets fixed red and blue gains for
indoor applications.
• ATW: Enables Auto Tracing White Balance.
• Sodium Vapour Lamp: Sets the specific fixed
values when sodium vapour lamps are used
on the scene.
• Auto Sodium Vapour Lamp: Sets the specific
automatic white balance when sodium
vapour lamps are used on the scene.
2. Red Value: Sets the value of the red gain.
3. Blue Value: Sets the value of the blue gain.
WHITE BALANCE
------------------------
1>MODE : MANUAL
2 RED VALUE : 0
3 BLUE VALUE: 0
Fig. 25
The menu dynamically auto-configures based on the
camera installed and the choice made, showing the
parameters on which you can act.
6.1.5.7 Advanced Setting Menu (Other)
It allows you to configure the following parameters:
1. Sharpness: Sets the sharpness value of the
image.
2. High Resolution: Enables the High Resolution
function. The output video signal has a higher
resolution.
3. Wide Dynamic: Enables the Wide Dynamic
function. It improves vision when some zones
within the frame are much brighter than others.
4. Stabilizer: Enables the electronic image
stabilization function.
5. Progressive Scan: Enables the Progressive Scan
function. Gives a more stable image when the
Pan & Tilt is connected to a video server.
6. Noise Reduction: Sets the noise reduction
level. Vary the parameter according to the
environmental conditions to obtain a higher
contrast image.
7. Backlight Compensation: Enables the
Backlight Compensation function. It improves
vision of any dark zone in the image.
OTHER
------------------------
1 SHARPNESS : 6
2 HIGH RESOLUTION : N
3 WIDE DYNAMIC : AUTO
4 STABILIZER : N
5 PROGRESSIVE SCAN: N
6 NOISE REDUCTION : 2
7 BACKLIGHT COMP. : N
Fig. 26
The menu dynamically auto-configures based on the
camera installed and the choice made, showing the
parameters on which you can act.