Viega 8502 User manual

for floor-standing WC, walling in and around, compatible with all
WC flush plates for Prevista
Model Year built:
8502 from 09/2018
en_INT
3H concealed cistern
Instructions for Use

3H concealed cistern 2 from 20

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Standards and regulations 6
2.2 Intended use 6
2.2.1 Areas of use 6
2.3 Product description 7
2.3.1 Overview 7
2.3.2 Technical data 7
3Handling 8
3.1 Assembly information 8
3.1.1 Installation dimensions 8
3.2 Assembly 10
3.2.1 Mounting concealed cisterns 10
3.2.2 Connecting concealed cistern 13
3.2.3 Setting up and bricking in the concealed cistern 16
3.2.4 Setting the flush volume 18
3.3 Cleaning and maintenance 20
3.4 Disposal 20
Table of contents
3H concealed cistern 3 from 20

1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
nDrywall builder
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
About these instructions for use
3H concealed cistern 4 from 20

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e.g. EN) and/or in Germany
(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
3H concealed cistern 5 from 20

2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe and
are provided as a support feature.
Regulations from section: Fields of application
Scope / Notice Regulations applicable in Ger‐
many
Specifications for installations
inside buildings conveying water
for human consumption
EN 806-2
2.2 Intended use
2.2.1 Areas of use
The 3H concealed cistern is suitable for mounting on a floor-standing
WC and for walling in or around. Flush actuation is possible from the
front.
This model is equipped with dual flush technology and is delivered
without flush plates. For complete mounting, a WC flush plate for Pre‐
vista must be purchased additionally.
The cistern is designed to supply cold water. The application limits must
be taken into account for the cold water supply, see Ä „Regulations
from section: Fields of application“ on page 6.
Product information
3H concealed cistern 6 from 20

2.3 Product description
2.3.1 Overview

Fig. 1: Components
1 3H concealed cistern
2 fixing material
3 dowels and screws
4 flushing pipe
5 Protective plug
6 Revision shaft cover for the cistern
7 Corner valve
2.3.2 Technical data
The product has the following technical data:
Pre-assembled
water connection
R½
Small flush volume Factory setting approx. 3 l
setting range approx. 2–4 l
Large flush volume Factory setting approx. 6 l
setting range approx. 3.5–7.5 l
Product information
3H concealed cistern 7 from 20

3 Handling
3.1 Assembly information
3.1.1 Installation dimensions



Fig. 2: Dimensional drawing 1
Handling
3H concealed cistern 8 from 20




Fig. 3: Dimensional drawing 2
Handling
3H concealed cistern 9 from 20

3.2 Assembly
3.2.1 Mounting concealed cisterns
Break the locking clips off the wall mountings.
Push the wall mountings into the mounting brackets.
Insert the locking clips.
Insert the holder into the mounting bracket for the drain elbow.
Handling
3H concealed cistern 10 from 20

Grease the flushing pipe.
Insert the flushing pipe.
Check the seal is located.
Adjust the construction height of the concealed cistern in accord‐
ance with the on-site marking of the upper edge of the finished
floor.
Mark the fixing points.
Drill the holes.
Insert the dowels.
Align the concealed cistern.
Tighten the concealed cistern via the mounting brackets using a fork
spanner.
ðThe concealed cistern is attached to the wall.
9

煼

Handling
3H concealed cistern 11 from 20

Cut out recesses for the drain elbow and the flush plate in the pre-
wall finish.
Align the concealed cistern on the pre-wall finish.
Tighten the concealed cistern via the mounting brackets.
ðThe concealed cistern is fastened.
Mounting in the wooden support profile
Handling
3H concealed cistern 12 from 20

3.2.2 Connecting concealed cistern
Turn the cover plate lock 90° in anti-clockwise direction.
Remove the cover plate.
Place the press connector onto the water supply.
Press the connection.
Seal the threaded connectors of the corner valve.
Screw the corner valve into the thread side of the connector.
Handling
3H concealed cistern 13 from 20

Remove the plug.
Insert the corner valve into the cistern.
INFO! Observe the proper fit of the corner valve.
Use the lock nuts to screw the corner valve and the cistern to each
other.
Remove the protective cap from the water supply hose.
Screw the water supply hose and the corner valve to each other.
Insert the cover plate into the cistern.



Handling
3H concealed cistern 14 from 20

Turn the cover plate lock by 90° in a clockwise direction.
Place the revision shaft on the cover plate.
To remove the revision shaft, press in the fixing clips at the
side.

Handling
3H concealed cistern 15 from 20

3.2.3 Setting up and bricking in the concealed cistern
Fit the protective plug of the flushing pipe.
Brick in the concealed cistern.
NOTICE! Do not load the concealed cistern.
Handling
3H concealed cistern 16 from 20

The wall construction must be at least 10 mm.
Tile the concealed cistern.
NJO
Handling
3H concealed cistern 17 from 20

3.2.4 Setting the flush volume
Requirements:
nThe cistern is freely accessible.
nThe water supply has been shut off.
nThe ceramic has been mounted.
Fold the tabs forward.
Lift the drain valve.
Remove the drain valve through the revision opening.
Handling
3H concealed cistern 18 from 20

Set the large flush volume at the drain valve.
Set the small flush volume at the drain valve.
--
Handling
3H concealed cistern 19 from 20

Requirements:
nThe drain valve has been dismounted.
nThe flushing throttle has been removed.
Unlock the flushing throttle.
Set the flush flow at the throttle.
Lock the flushing throttle.
3.3 Cleaning and maintenance
The concealed cistern is constantly under mechanical, chemical, and
physical stress. For this reason, the components must be cleaned as
required, and the drain and filling valve seals renewed.
In areas or regions with hard water due to high concentration of calcium
or magnesium salts, there is the risk of limescale deposits developing
on the inlet and drain valves. The valves may have to be replaced,
depending on the extent of the deposits.
3.4 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Setting the flush flow
Cleaning and maintenance of the concealed cistern
Handling
3H concealed cistern 20 from 20